DOW CHEMICAL CO -- POLYETHYLENE 10462N HIGH DENSITY, 47055
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CJYXJ
MSDS NAME: POLYETHYLENE 10462N HIGH DENSITY, 47055
Responsible Party
Name: DOW CHEMICAL CO
Address: 100 LARKIN CENTER
City: MIDLAND MI 48674
Info Phone: 800-258-2436
Emergency Phone Number: 517-636-4400
Resp. Party Other MSDS No.: 002101
Review Ind: Y
Published: Y
=======================================================
Contractor Summary
=======================================================
Name: DOW CHEMICAL CO
Address: 100 LARKIN CENTER
City: MIDLAND MI 48674
Phone: 800-258-2436
=======================================================
Item Description Information
=======================================================
=======================================================
Ingredients
=======================================================
Cas: 26221-73-8
Name: COPOLYMER OF ETHYLENE AND OCTENE-1
Percent by Wt: 100.
=======================================================
Health Hazards Data
=======================================================
LD50 LC50 Mixture: SEE TOXICOLOGICAL INFORMATION.
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: YES
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Effects of Exposure: EYE: SOLID OR DUST MAY CAUSE IRRITATION OR CORNEAL INJURY
DUE TO MECHANICAL ACTION. SKIN: ESSENTIALLY NONIRRITATING. MECHANICAL INJURY
ONLY. A SINGLE PROLONGED SKIN EXPOSURE IS NOT LIKELY TO RESULT IN MATERIAL
BEING ABSORBED THROUGH SKIN IN HARMFUL AMOUNTS. INGESTION: SINGLE DOSE ORAL
TOXICITY IS BELIEVED TO BE VERY LOW. NO HAZARDS ANTICIPATED FROM INGESTION
INCIDENTAL TO INDUSTRIAL EXPOSURE. INHA LATION: DUST MAY CAUSE IRRITATION TO
UPPER RESPIRATORY TRACT. SYSTEMIC (OTHER TARGET ORGANS) EFFECTS: NO RELEVANT
INFORMATION FOUND.
Signs And Symptions Of Overexposure: SEE HEALTH HAZARDS.
First Aid: EYES: FLUSH WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES; MECHANICAL
IRRITATION ONLY. SKIN: WASH OFF IN FLOWING WATER OR SHOWER. INGESTION: CALL
MD IMMEDIATELY (FP N). NO ADVERSE EFFECTS ANTICIPATED B Y THIS ROUTE OF
EXPOSURE INCIDENTAL TO PROPER INDUSTRIAL HANDLING. INHALATION: REMOVE TO
FRESH AIR IF EFFECTS OCCUR. CONSULT MD.
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: SWEEP UP.
Waste Disposal Methods: DO NOT DUMP INTO ANY SEWERS, ON GROUND/INTO ANY BODY OF
WATER. ALL DISP METHS MUST BE IN COMPLIANCE W/ALL FED, STATE/PROVINCIAL &
LOC LAWS & REGS. REGS MAY VARY IN DIFF LOCATIONS. WASTE CHARACTS &
COM PLIANCE W/APPLIC LAWS ARE RESPONSIBILITY SOLELY OF WASTE GENERATOR. DOW
CHEM CO HAS NO CONTROL OVER MANAGEMENT PRACTICES/MFG PROCESSES OF (OTHER
INFO)
Handling And Storage Precautions: GOOD HOUSEKEEPING AND CONTROLLING OF DUSTS
ARE NECESSARY FOR SAFE HANDLING OF PRODUCT. ELECTRICALLY GROUND ALL
EQUIPMENT. THE POLYMER PELLETS AND FINISHED ARTICLE SHOULD BE STORED IN A
MANNER THAT THE Y ARE NOT EXPOSED TO ULTRA-VIOLET LIGHT.
Other Precautions: EMERGENCY OVERVIEW: COLOR: WHITE. APPEARANCE: GRANULES,
PELLETS OR POWDER. ODOR: NONE. TOXIC FUMES RELEASED IN FIRE SITUATIONS.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Extinguishing Media: WATER, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures: USE NIOSH APPRVD SCBA & FULL PROT EQUIP (FP N).
IF PROT EQUIP IS NOT AVAIL/NOT USED, FIGHT FIRE FROM PROTECTED LOCATION/SAFE
DIST. KEEP PEOPLE AWAY. ISOLATE FIRE AREA & DENY UNNEC ENTRY. COOL
SURROUND S W/WATER TO LOCALIZE FIRE ZONE. HAND HELD CARBON DIOXIDE/DRY CHEM
EXTINGS MAY BE USED FOR SM FIRES. SOAK THORO(SUPDAT)
Unusual Fire/Explosion Hazard: DENSE SMOKE IS EMITTED WHEN BURNED W/OUT
SUFFICIENT OXYG. MECH HNDLG CAN CAUSE FORM OF DUSTS. TO REDUCE POTNTL FOR
DUST EXPLO, DO NOT PERMIT DUST TO ACCUM. HAZ COMBUST PRODS:UNDER FIRE CNDTNS
POLYMERS DECOMPOSE. SMOKE MAY CONTAIN POLYMER FRAGMENTS OF VARYING
COMPOSITIONS IN ADDN TO UNIDENTIFIED TOX &/OR IRRIT (SUPDAT)
=======================================================
Control Measures
=======================================================
Respiratory Protection: FOR MOST CONDITIONS, NO RESPIRATORY PROTECTION SHOULD
NEEDED; HOWEVER, IF HANDLING AT ELEVATED TEMPERATURES WITHOUT SUFFICIENT
VENTILATION, USE A NIOSH APPROVED AIR-PURIFYING RESPIRATOR. IN DUSTY ATMO
SPHERES, USE A NIOSH APPROVED DUST RESPIRATOR.
Ventilation: GOOD GENERAL VENTILATION SHOULD BE SUFFICIENT FOR MOST CONDITIONS.
LOCAL EXHAUST VENTILATION MAY BE NECESSARY FOR SOME OPERATIONS.
Protective Gloves: IMPERVIOUS GLOVES (FP N).
Eye Protection: ANSI APPROVED CHEMICAL WORKERS GOGGLES (FP N).
Other Protective Equipment: EYE WASH AND DELUGE SHOWER MEETING ANSI DESIGN
CRITERIA (FP N). NO PRECAUTIONS OTHER THAN CLEAN BODY-COVERING CLOTHING
SHOULD BE NEEDED.
Supplemental Safety and Health: FIRE FIGHT PROC: WITH WATER TO COOL &
PREVENT REIGNITION. -- EXPLO HAZ: COMPOUNDS. HAZARDOUS COMBUSTION PRODUCTS
MAY INCLUDE & ARE NOT LIMITED TO CARBON MONOXIDE & CARBON DIOXIDE.
NFPA RATINGS: HEALTH - 0; FLAMMABILITY - 1; REACTIVITY - 0.
=======================================================
Physical/Chemical Properties
=======================================================
Spec Gravity: 0.84 - 0.97 (OR DENSITY)
Solubility in Water: NIL (OR MISCIBILITY)
Appearance and Odor: TRANSLUCENT WHITE, SOLID PELLETS, GRANULES, OR POWDER; NO
ODOR.
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: PRODUCT CAN DECOMPOSE AT ELEVATED TEMPERATURES.
Materials To Avoid: NONE KNOWN.
Hazardous Decomposition Products: PROCESSING MAY RELS FUMES WHICH MAY INCL
POLYMER FRAGMENTS & OTHER DECOMP PRODS. FUMES CAN BE IRRIT. AT TEMPS
EXCEEDING MELT TEMPS, POLYMER FRAGMENTS CAN OCCUR. HAZ DECOMP PRODS DEPEND
(OTHER INFO)
Hazardous Polymerization Indicator: NO
Conditions To Avoid Polymerization: WILL NOT OCCUR.
=======================================================
Toxicological Information
=======================================================
Toxicological Information: FOR DETAILED TOXICOLOGICAL DATA, WRITE OR CALL
ADDRESS OR NON-EMERGENCY NUMBER SHOWN IN SECTION 1. INGESTION: SINGLE DOSE
ORAL LD50 HAS NOT BEEN DETERMINED.
=======================================================
Ecological Information
=======================================================
Ecological: FOR DETAILED ECOLOGICAL DATA, WRITE/CALL ADDRESS/NON-EMERGENCY
NUMBER SHOWN IN SECTION 1. ENVIRON FATE: MOVEMENT & PARTITIONING: NO
BIOCONCENTRATION IS EXPECTED BECAUSE OF HIGH MOLECULAR WT (MW > 1000 ). IN
TERRESTRIAL ENVIRON, MATL IS EXPECTED TO REMAIN IN SOIL. IN AQUATIC ENVIRON,
MATL IS EXPECTED TO FLOAT. DEGRADATION & PERSISTENCE: THIS WATER
INSOLUBLE POLYMERIC SOLID IS EXPECTED TO BE INERT IN ENVIRON. SURFACE
PHOTODEGRADATION IS EXPECTED W/EXPOS TO SUNLIGHT. NO APPRECIABLE
BIODEGRADATION IS EXPECTED. ECOTOXICITY: NOT EXPECTED TO BE ACUTELY TOXIC.
=======================================================
MSDS Transport Information
=======================================================
Transport Information: DEPARTMENT OF TRANSPORTATION (D.O.T.): THIS PRODUCT IS
NOT REGULATED BY D.O.T. WHEN SHIPPED DOMESTICALLY BY LAND. CANADIAN TDG
INFORMATION: THIS PRODUCT IS NOT REGULATED BY TDG WHEN SHIPPED DOMESTICAL LY
BY LAND.
=======================================================
Regulatory Information
=======================================================
Sara Title III Information: SARA 313 INFO: TO THE BEST OF MFR'S KNOWLEDGE, THIS
PRODUCT CONTAINS NO CHEMICAL SUBJECT TO SARA TITLE III SECTION 313 SUPPLIER
NOTIFICATION REQUIREMENTS. SARA HAZARD CATEGORY: THIS PRODUCT HAS BEEN R
EVIEWED ACCORDING TO EPA "HAZARD CATEGORIES" PROMULGATED UNDER SECTIONS 311
& 312 OF THE SUPERFUND AMENDMENT AND REAUTHORIZATION ACT OF 1986 (SARA
TITLE III) & IS CONSIDERED, UNDER APPLICABLE DEFINITI ONS, TO MEET THE
FOLLOWING CATEGORIES: NOT TO HAVE MET ANY HAZARD CATEGORY.
Federal Regulatory Information: TOXIC SUBSTANCES CONTROL ACT (TSCA): ALL
INGREDIENTS ARE ON THE TSCA INVENTORY OR ARE NOT REQUIRED TO BE LISTED ON THE
TSCA INVENTORY. OSHA HAZARD COMMUNICATION STD: THIS PRODUCT IS NOT A
"HAZARDOUS C HEMICAL" AS DEFINED BY OSHA HAZARD COMMUNICATION STD, 29 CFR
1910.1200. CANADIAN REGS: W INFO: THE CANADIAN WORKPLACE HAZARDOUS MATERIALS
INFO SYSTEM (W) CLASSIFICATION FOR THIS PRODUCT IS: TH E PRODUCT IS NOT A
"CONTROLLED PRODUCT" UNDER W.
State Regulatory Information: STATE RIGHT-TO-KNOW: THIS PRODUCT IS NOT KNOWN TO
CONTAIN ANY SUBSTANCES SUBJECT TO THE DISCLOSURE REQUIREMENTS OF: NEW JERSEY
&/OR PENNSYLVANIA. -- OTHER INFO: REACTIVITY INFO SECTION IN THIS MSDS. A
S A SERVICE TO ITS CUSTOMERS, DOW CAN PROVIDE LISTS OF COMPANIES WHICH
RECYCLE, REPROCESS OR MANAGE CHEMICALS OR PLASTICS & COMPANIES THAT
MANAGE USED DRUMS. TELEPHONE DOW'S CUSTOMER INFO CENTER AT 80 0-258-2436 OR
517-832-1556 FOR FURTHER DETAILS.
=======================================================
Other Information
=======================================================
Other Information: NOTE: REGULATORY INFO (NOT MEANT TO BE ALL-INCLUSIVE --
SELECTED REGS REPRESENTED). -- HAZ DECOMP PROD: UPON TEMP, AIR SUPPLY &
PRESENCE OF OTHER MATLS. HAZ DECOMP PRODS MAY INCL TRACE AMTS OF ALDEHYD ES,
ALCOHOLS, HYDROCARBONS, ORGANIC ACIDS. -- WASTE DISP METH: PARTIES
HNDLG/USING THIS MATL. INFO PRESENTED HERE PERTAINS ONLY TO PROD AS SHIPPED
IN ITS INTENDED CNDTN AS DESCRIBED IN MSDS (COMPOSITI ON/INFO ON INGS
SECTION). FOR UNUSED & UNCONTAM PROD, PREF OPTIONS INCL SENDING TO
LICENSED, PERMITTED: RECYCLER, RECLAIMER, INCIN/OTHER THERMAL DESTRUCTION
DEVICE & LANDFILL. FOR ADDNL INFO, REFER TO STABILITY & (STATE
REGULATORY INFO)
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: POLYETHYLENE 10462N HIGH DENSITY, 47055
Company: DOW CHEMICAL CO
Street: 100 LARKIN CENTER
City: MIDLAND MI
Zipcode: 48674
Health Emergency Phone: 517-636-4400
Label Required IND: Y
Date Of Label Review: 01/18/2000
Status Code: A
Origination Code: F
Eye Protection IND: YES
Skin Protection IND: YES
Signal Word: CAUTION
Respiratory Protection IND: YES
Health Hazard: Slight
Contact Hazard: Slight
Fire Hazard: None
Reactivity Hazard: None
Hazard And Precautions: ACUTE: EYE: SOLID OR DUST MAY CAUSE IRRITATION OR
CORNEAL INJURY DUE TO MECHANICAL ACTION. SKIN: ESSENTIALLY NONIRRITATING.
MECHANICAL INJURY ONLY. A SINGLE PROLONGED SKIN EXPOSURE IS NOT LIKELY TO RE
SULT IN MATERIAL BEING ABSORBED THROUGHSKIN INHARMFUL AMOUNTS. INGESTION:
SINGLE DOSE ORAL TOXICITY IS BELIEVED TO BE VERY LOW. NO HAZARDS ANTICIPATED
FROM INGESTION INCIDENTAL TO INDUSTRIAL EXPOSURE. INHALATION: DUST MAY CAUSE
IRRITATION TO UPPER RESPIRATORY TRACT. SYSTEMIC (OTHER TARGET ORGANS)
EFFECTS: NO RELEVANT INFORMATION FOUND. CHRONIC: NONE SPECIFIED BY
MANUFACTURER (FP N).
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
INPRO-CLEAN 2500, 4407
| |
|
HBI-101 MIL
| 64742-94-5
67-64-1
1330-20-7 |
|
BIO-DUR 561 CURING AGENT WHITE, BD561-17880B
| |
|
AOS HEAT SINK COMPOUND, 52022
| |
|
0638, METAL MEDIC
| |
|
850 SERIES WATER BORNE ACRYLIC EPOXY TOPCOAT
| |
|
DOUBLE BUBBLE GREEN, 04004 PART B
| |
|
LESLIE'S FILTER CLEANER
| |
|
LESLIE'S SPRAY & RINSE
| |
|
CUT-MAX 570-ND, 415707
| 64742-52-5
64742-46-7
68410-99-1 |
|
PR-421, 04211 PART B
| |
|
SPRAY STENCIL INK, ALL COLORS, 27004
| |
|
LESLIE'S DE FILTER CLEANER
| |
|
IRM 903
| 64742-52-5 |
|
SILASTIC 738 RTV NON-CORROSIVE ADHESIVE/SEALANT WHITE
| 7631-86-9
1185-55-3
546-68-9
67-63-0
67-56-1
70131-67-8
80801-30-5 |
|
0810002,ANDEROL 401 D SYNTHETIC INSTRUMENT OIL
| |
|
CRISP GUM REMOVER, F4260
| |
|
TONER CARTRIDGE, FO-45ND
| |
|
ZYMIT
| 9003-11-6
57-55-6
9014-01-1
56-81-5 |
|
INTERSHIELD PRORECO 609 CLEAR BASE, PRA610
| 110-43-0
108-10-1
108-65-6
123-86-4 |
|
INTERSHIELD PRORECO 609 CLEAR CONVERTER, PRA611
| 3779-63-3
123-86-4 |
|
TRIFREE BRAKE CLEANER, 03620
| 142-82-5
67-64-1
108-87-2
124-38-9
110-82-7
108-88-3
628-63-7 |
|
SCOTCHBOND MULTIPURPOSE ADHESIV, 70-2010-0402-8
| 1565-94-2
868-77-9
10373-78-1
10287-53-3
58109-40-3 |
|
PRESOLVE (AEROSOL), 01420
| 64742-88-7
5989-27-5
124-38-9 |
|
AKROFAX A SOFT (CAKE), 67378
| |
|
FLOR-DECORATIVE FLAKES
| 108-05-4
7727-43-7
14807-96-6
13845-36-8
13463-67-7
1333-86-4
7440-50-8 |
|
SHIPPING-MATE BOX RENU COATING, 62-4973-4830-0
| 67-64-1
78-93-3
68512-98-1
74-98-6
8030-30-6
108-88-3
1330-20-7
64-17-5
13463-67-7 |
|
PLY#2 PROTECTIVE SKIN CREAM
| |
|
EVERLUBE 9002 (10-955)
| |
|
D.E.H. 26 EPOXY CURING AGENT
| 112-57-2
112-24-3
68131-73-7 |
|
VCI-238 ELECTRICORR
| |
|
STADIS 450 CONDUCTIVITY IMPROVER (DINNSA STABILIZER)
| |
|
CONSERVE SC TURF & ORNAMENTAL INSECT CONTROL
| |
|
SAG 10
| |
|
INTERSHIELD PRORECO 508 NAVY BLUE PART A, PRA559
| 110-43-0
13463-67-7
1333-86-4 |
|
PLY#2 PROTECTIVE SKIN CREAM
| |
|
INTERSHIELD PRORECO 508, PRA556, DARK GRAY PART A
| 110-43-0
13463-67-7
1333-86-4
7631-86-9 |
|
ART UTILITY SPRAY GLUE
| 75-09-2
26523-64-8
124-38-9 |
|
F. P. ETHYL METHACRYLATE MONOMER
| |
|
MAXI-LUBE, 4098
| |
|
LUBE SHIELD PLUS, 4220
| |
|
CALCIUM OXIDE
| |
|
BARIUM NITRATE
| |
|
DRI-SLIDE MULTI-PURPOSE LUBRICANT
| 64742-88-7
1317-33-5
7782-42-5
64742-52-5
85595-45-5
26566-95-0 |
|
DRI-SLIDE MULTI-PURPOSE LUBRICANT AEROSOL
| 64742-88-7
1317-33-5
7782-42-5
64742-52-5
85595-45-5
26566-95-0
68476-86-8 |
|
VESTENAMER 8012, 1252000
| |
|
CAROLINA BLU DNA STAIN
| |
|
SUPER ALL FLEET 30
| 63649-42-3
68649-42-3 |
|
POLYETHYLENE 10462N HIGH DENSITY, 47055
| 26221-73-8 |
|
POLYETHYLENE 955I LOW DENSITY, 23821
| 9002-88-4 |
|
|