===================== Product Identification =====================
MSDS NAME:COMPONENT FR-A
NIIN:00N006133
MSDS Number: BCLZZ
=== Responsible Party ===
Company:SEALED AIR CORPORATION, INSTAPAK DIVISION
Emergency Phone Num:203-792-2360
CAGE:OC634
=== Contractor Identification ===
Company:SEALED AIR CORP INSTAPAK DIVISION
Address:OLD SHERMAN TPKE
Box:City:DANBURY
State:CT
ZIP:06810
Country:US
Phone:203-791-3500/800-424-9300(CHEMTREC)
CAGE:51614
Company:SEALED AIR CORPORATION
Address:OLD SHERMAN TNPK
City:DANBURY
State:CT
ZIP:06810
Phone:203-792-2360,800-424-9300 CHEMTREC
CAGE:OC634
============= Composition/Information on Ingredients =============
Name:METHYLENE BISPHENYL ISOCYANATE (MDI) (SARA III)
CAS:101-68-8
RTECS #:NQ9350000
Fraction by Wt: 40%
OSHA PEL:C, 0.02 PPM
ACGIH TLV:0.005 PPM; 9192
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB
Name:HIGHER POLYMERS OF SIMILAR STRUCTURE; % IS APPROX.
Fraction by Wt: 40%
Name:TRICHLOROFLUOROMETHANE (CFC-11) (SARA III)
CAS:75-69-4
RTECS #:PB6125000
Fraction by Wt: 5%
OSHA PEL:1000 PPM
ACGIH TLV:C, 1000 PPM; 9293
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS
Ozone Depleting Chemical:1
===================== Hazards Identification =====================
Effects of Overexposure:IRRIT:MUCOUS MEMBRANES,RESP
TRACT.COUGH,HDCH,SHORT BRTH,TIGHT CHEST.RPTD OVEREXPOS:ALLERGENIC
SENSIT
======================= First Aid Measures =======================
First Aid:SKIN:WASH W/SOAP & WATER AT LEAST 5 MINS.EYES:WASH W/LRG
AMOUNT OF WATER AT LEAST 15 MINS, SEE MD. INGEST:INDUCE VOMIT, CALL
MD. INHAL:MOVE TO UNCONTAMINATED AREA, ADMINISTER O*2 IF NEC, CALL
MD.
===================== Fire Fighting Measures =====================
Flash Point:385F,196C COC
Extinguishing Media:CO*2, DRY CHEMICAL, CHEMICAL FOAM
Fire Fighting Procedures:WEAR PROTECTIVE CLTHNG & SCBA TO PROTECT FROM
PRODUCT VAPORS
Unusual Fire/Explosion Hazard:PRESSURE WILL DEVELOP W/HEAT IN CLSD
CNTNRS.
================== Accidental Release Measures ==================
Spill Release Procedures:ABSORB IN SAWDUST OR SWEEPING CMPD;REMOVE FROM
AREA IN OPEN DRUMS & WET W/WATER CONTAINING ABOUT 1% AMMONIA BEFORE
DISPOSAL. NOTE THAT EPA REGULATIONS CLASSIFY THE FLUOROCARBON
COMPONENT AS A "HAZARDO US WASTE".
====================== Handling and Storage ======================
Handling and Storage Precautions:PROTECT FROM HUMID AIR. STORE BETWEEN
10-120F. USE BETWEEN 60-90F. OPEN CONTAINERS CAREFULLY:IF OVER 100F
CONTENTS WILL BE UNDER PRESSURE.
Other Precautions:NO SMOKING IN AREA OF USE.DO NOT USE IN GENERAL
VICINITY OF ARC WELDING,OPEN FLAMES,HOT SURFACES.HEAT &/OR UV
RADIATION MAY CAUSE THE FORMATION OF CHLORIDES,FLUORIDES OR
PHOSGENE.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:NIOSH/MSHA APPROVD CANISTER TYPE GAS MASK FOR
ORG VAP,MASK W/EXTERNA
Ventilation:LOCAL EXHAUST TO MAINTAIN VAPOR CONCENTRATION BELOW TLV.
Protective Gloves:CHEMICAL RESIST
Eye Protection:SAFETY GOGGLES
Other Protective Equipment:SAFETY SHOWER/EYE WASH.RESP:AIR SOURCE OR
SCBA,MFR.(SUPP DAT
Supplemental Safety and Health
BP IS APPROX. VP MEASURED AT 77F,25C. PART A OF A 2 PART PRODUCT. PART
B IS FOUND UNDER NSN 8135-00-130-9753.RECM RESP PROTECT POSS NOT
SUIT FOR ALL CASES. CONSULT IND HYGIENIST/SAF OFF IF NEC
================== Physical/Chemical Properties ==================
Boiling Pt:B.P. Text:150F,66C
Vapor Pres:100
Vapor Density:4.8
Spec Gravity:1.26
Solubility in Water:INSOLUBLE
Appearance and Odor:BROWN LIQUID, SLIGHTLY AROMATIC ODOR.
Percent Volatiles by Volume:5.0
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
H*2O,ALCOHOLS,STRONG BASES,METAL CMPDS,SURFACE ACTIVE AGENTS
Stability Condition to Avoid:TEMPS <10F(CAUSES CRYSTAL;>120F(SLOW
INCREASE IN VISCOSITY)
Hazardous Decomposition Products:CHLORIDES, FLUORIDES & PHOSGENE
Conditions to Avoid Polymerization:MOISTURE,OTHER MATERIALS THAT REACT
W/ISOCYANATE.
==================== Disposal Considerations ====================
Waste Disposal Methods:THE SOLIDIFIED ISOCYANATE PORTION(AFTER WETTING)
CAN BE DISPOSED OF IN SOLID TRASH. ANY RESIDUAL FLUOROCARBON MUST
BE DISPOSED OF IN ACCORDANCE W/EPA & LOCAL HAZARDOUS WASTE DISPOSAL
REGS. ALL METHODS MUST BE IAW LOCAL, STATE & FEDERAL REGS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
WHITE AIR DRY COAT AE146 5294
| 111-76-2
71-36-3
108-10-1
1330-20-7 |
|
THINNER SV2607
| 111-76-2
71-36-3
1330-20-7
67-64-1 |
|
PISTOL PETE 602
| 109-99-9
108-94-1
78-93-3 |
|
TURCOAT DETERGENT
| |
|
TRUSTAN 7
| 7664-38-2
107-21-1
67-63-0 |
|
TRA-BOND F230 RESIN
| |
|
TRA-BOND F230 HARDENER
| |
|
STRIPPER 28B,FORMULA 22-18
| |
|
STRIPPER 28A,FORMULA 22-17
| 107-15-3 |
|
CN-3
| 1310-73-2
143-33-9 |
|
LAMINAR GT DRY FILM PHOTOPOLYMER
| |
|
DYNACHEM,DEVELO-AID
| |
|
BRIGHT CADMIUM PLATING SOLUTION
| 1306-19-0
143-33-9 |
|
BRIGHT ACID TIN
| 7664-93-9
7488-55-3 |
|
KEM SIGN FINISHING CLEAR, V20V3
| 8030-30-6
108-88-3 |
|
POLYSHELL T-556
| 8030-30-6
138-86-3
7732-18-5 |
|
POLYSHELL T-557
| 8030-30-6 |
|
POLYSHELL T-558
| 8030-30-6
7732-18-5 |
|
POLYSHELL T-559
| 8030-30-6
7732-18-5 |
|
TWIN-KOOL
| |
|
INTERTUF SILVER, EXEMPT, JAA021E
| 8030-30-6
1330-20-7
7439-92-1 |
|
INTERCLENE EXTRA RED OFFSHORE ANTIFOULING
| 1317-39-1
1330-20-7
8030-30-6
64-17-5 |
|
BOTTOMKOTE ANTIFOULING RED, 49
| 8030-30-6
1330-20-7
64-17-5
1317-39-1 |
|
BOSTIK 1127,ADHESIVE,PART A
| 108-88-3
141-78-6
67-64-1 |
|
ROYAL M6280
| 67-64-1
108-88-3
1330-20-7 |
|
COMPONENT FR-A
| 101-68-8
75-69-4 |
|
INSTAPAK PORT CLEANER
| 96-48-0 |
|
PC-504 ULTRASEAL, PT A
| |
|
VAZO CATALYST, 50%, PT B
| 7732-18-5 |
|
PEN
| 8002-05-9 |
|
401 SOLVENT DEGREASER
| 71-55-6 |
|
VARSOL 3
| |
|
OSPHO RUST DISSOLVER
| 7732-18-5
7664-38-2
10588-01-9 |
|
268 AQUA-QUAT
| 85-00-7 |
|
B62 N 71,TILE CLAD I,HI BILD PRIMER,PART A
| 71-36-3
1330-20-7 |
|
B69 Y 22,TANK CLAD II,HI BILD ENAMEL PRIMER
| 75-56-9
541-85-5
108-10-1
1330-20-7 |
|
GALVANIZED IRON PRIMER, B50 A 1
| 64742-47-8
7439-92-1
14807-96-6
7440-43-9
7440-66-6 |
|
A33 A 37,FLOOR ENAMEL MEDIUM GRAY
| 8030-30-6 |
|
F65 E 1,KEM LUSTRAL ENAMEL,ORANGE
| 7758-97-6
7439-92-1
1330-20-7
8030-30-6 |
|
B62 W 101,TILE CLAD II ENAMEL PURE WHITE,A
| 110-80-5
1330-20-7
8030-30-6 |
|
F65 G 40,KEM LUSTRAL ENAMEL MEDIUM GREEN
| 107-41-5
1330-20-7
8030-30-6
111-15-9 |
|
B69 W 70,TILE CLAD II,DOVER WHITE,PART 2
| 594-44-5
1330-20-7
8030-30-6 |
|
B69 W 17, C & M HI-BILD ENAMEL,WHITE
| 1330-20-7
8030-30-6 |
|
B69 G 19,C & M RESIST ENAMEL,SAFETY GREEN
| 1330-20-7
8030-30-6 |
|
B69 R 19,C & M ENAMEL OSHA RED
| 18540-29-9
7439-92-1
75-56-9
1330-20-7
8030-30-6 |
|
B69 N 11,C & M RESIST HI BILD PRIMER
| 7439-92-1
75-56-9
1330-20-7
108-88-3
8030-30-6 |
|
A40 W 5,CLASSIC 99 ENAMEL-PURE WHITE
| 8030-30-6
107-41-5
8030-30-6
96-29-7 |
|
B34 W 101,PRO-MAR ALKYD,PASTE BASE ENAMEL
| 8030-30-6
107-41-5
8030-30-6 |
|
EPON RESIN 871
| |
|
LIQUIGEST I OR M
| |
|
|