===================== Product Identification =====================
MSDS NAME:EUTECROD 1900
NIIN:00N080097
MSDS Number: CFRZL
=== Responsible Party ===
Company:EUTECTIC CORP
Address:40-40 172ND ST
City:FLUSHING
State:NY
ZIP:11358-2799
Country:US
Info Phone Num:718-358-4000
Emergency Phone Num:718-358-4000
CAGE:72271
=== Contractor Identification ===
Company:EUTECTIC CORP
Address:9625-J SOUTHERN PINE BLVD
Box:City:CHARLOTTE
State:NC
ZIP:28273
Country:US
Phone:704-527-9800/ 800-221-1433
CAGE:72271
============= Composition/Information on Ingredients =============
Name:MAGNESIUM
CAS:7439-95-4
RTECS #:OM2100000
OSHA PEL:10 MG/M3 (MFR)
ACGIH TLV:15 MG/M3 (MFR)
Name:ALUMINUM (SARA 313)
CAS:7429-90-5
RTECS #:BD0330000
Fraction by Wt: 1-5%
OSHA PEL:15 MG/M3 DUST
ACGIH TLV:10 MG/M3 DUST
Name:ZINC (SARA 313) (CERCLA) (MFR INVALID CAS # 7440-66-5)
CAS:7440-66-6
RTECS #:ZG8600000
Fraction by Wt: 5-10%
OSHA PEL:N/K
ACGIH TLV:N/K
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
Name:SUP DAT: INGS SECTION, PLUS THOSE OF BASE METAL & COATING,
ETC, AS NOTED ABOVE. REASONABLY EXPECTED CONSTITUENTS (ING 5)
RTECS #:9999999ZZ
Name:ING 4: OF FUME MAY INCL: COMPLEX OXIDES OF METALS LISTED IN
INGS SECTION; FLUX COATINGS MAY PRDCE FLUORIDE CMPDS,(ING 6)
RTECS #:9999999ZZ
Name:ING 5: METAL OXIDES, CARBON & SILICA. GASEOUS RXN PRODS MAY
INCL OZONE, CARBON MONOXIDE, CARBON DIOXIDE, NITROGEN(ING 7)
RTECS #:9999999ZZ
Name:ING 6: OXIDES, & CERTAIN INERT GASES USED AS SHIELDING
GASES. ONE REC WAY TO DETERMINE COMPOSITION & QTY OF FUMES(ING 8)
RTECS #:9999999ZZ
Name:ING 7: & GASES TO WHICH WORKERS ARE EXPOSED IS TO TAKE AIR
SAMPLE INSIDE WORKER'S HELMET IF WORN/IN WELDER'S (ING 9)
RTECS #:9999999ZZ
Name:ING 8: BRTHG ZONE. SEE ANSI/AWS 11.1 AVAIL FROM AMERICAN
WELDING SOCIEATY, P.O. BOX 351040, MIAMI, FL 33135. (ING 10)
RTECS #:9999999ZZ
Name:ING 9: ALSO FROM AWS F1.3 "EVALUATING CONTAMINANTS IN THE
WELDING ENVIRONMENT - A SAMPLING STRATEGY GUIDE", (ING 11)
RTECS #:9999999ZZ
Name:ING 10: WHICH GIVES ADDITIONAL ADVICE ON SAMPLING. FOR MORE
SPECIFIC INFORMATION CONTACT NEHC .
RTECS #:9999999ZZ
Name:EFTS OF OVEREXP: LUNG FIBROSIS, PNEUMOCONIOSIS/SIDEROSIS
(IRON DEPOSITS IN LUNG). METAL FUME FEVER: CAN BE (ING 13)
RTECS #:9999999ZZ
Name:ING 12: CAUSED BY INHAL OF CERTAIN METALLIC CMPDS DURING
WELDING, HEATING, BRAZING, SODERING/CUTTING OPERATIONS.(ING 14)
RTECS #:9999999ZZ
Name:ING 13: SYMPS ARE SIMILAR TO INFLUENZA TYPE SICKNESS INCL
CHILLS, FEVER, HEAD & MUSCLE ACHE, TIGHTNESS OF CHEST,(ING 15)
RTECS #:9999999ZZ
Name:ING 14: DRYNESS OF NOSE & MOUTH, MUSC PAIN, NAUS & VOMIT.
SYMPS USUALLY OCCUR W/IN SEVERAL HRS AFTER OVEREXP & (ING 16)
RTECS #:9999999ZZ
Name:ING 15: MAY LAST 3-24 HRS. CONSULT MD IMMED IF ANY OF THESE
SYMPS DEVELOP AFTER WELDING OPERATION. GEN NUISANCE (ING 17)
RTECS #:9999999ZZ
Name:ING 16: DUSTS: SKIN: POSS DRYING & MECH IRRIT. EYE CONT CAN
PRDCE PARTICULATE IRRIT. EXCESS INHAL CAN PRDCE (ING 18)
RTECS #:9999999ZZ
Name:ING 17: MILD PULMONARY IRRITATION & POSSIBLE NON-DISABLING
SLIGHT FIBROSIS OF THE LUNGS.
RTECS #:9999999ZZ
===================== Hazards Identification =====================
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: LITTLE/NO HAZS EXIST FOR ARC
WELDING ELECTRODES & BRAZING RODS BEFORE THEY ARE USED IN WELDING
PROCESS. INHAL: FUMES ASSOC W/HEATING, WELDING, BRAZING,
SOLDERING/CUTTING METALS CAN BE DANGEROUS TO YOUR HLTH & OVEREXP
CAN CAUSE LUNG DMG &/OTHER ORGAN DMG. EYES/SKIN: ARC RAYS &
ULTRAVIOLET LIGHT (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ: CAN INJURE EYES & BURN SKIN. LIQS
USED IN FLUXES & CHEM AIDS MAY CAUSE IRRIT/POSS CHEM BURNS. ELEC
SHOCK CAN KILL. INGEST: DANGER! MAY BE HARMFUL/FATAL IF SWALLOWED.
GEN WELDING FUMES: SHORT TERM OVEREXP MAY RSLT IN DIZZ,
NAUS/DRYNESS/IRRIT OF NOSE, THROAT/EYES. EXCESS OVEREXP MAY CAUSE
BRONCH ASTHMA,(ING 12)
Medical Cond Aggravated by Exposure:AGGRAVATION OF PREEXISTING
RESPIRATORY OR ALLERGIC CONDITIONS MAY OCCUR IN SOME WORKERS.
======================= First Aid Measures =======================
First Aid:INHAL: MOVE TO FRESH AIR SOURCE. CONT MD & ADVISE ON
INGREDIENTS. SKIN: THORO WASH HANDS/AFFECTED AREAS W/SOAP & WATER
TO REMOVE ALL RESIDUE. IF RASH/BURN DEVELOPS, CONSULT MD. EYES:
THORO FLUSH W/WAT ER FOR AT LEAST 15 MIN TO REMOVE ALL RESIDUE.
OBTAIN PROMPT MED ADVICE FOR FLUXES & CHEM AIDS. ADVISE MD OF
INGREDIENTS. INGEST: CALL MD &/OR LOCAL POISON CONTROL CENTER.
ADVISE OF INGREDIENTS.
===================== Fire Fighting Measures =====================
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:WEAR NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . TOXIC FUMES MAY BE PRODUCED.
Unusual Fire/Explosion Hazard:REFER TO ANSI Z49.1 FOR FIRE PREVENTION
DURING USE OF WELDING & ALLIED PROCESSES. ELECTRODE/BRAZE/SOLDERS:
NON-FLAMM. WELDING ARC, SPKS & FLAMES CAN (SUP DAT)
================== Accidental Release Measures ==================
Spill Release Procedures:USE APPROPRIATE MEASURES TO KEEP AIRBORNE DUST
LEVELS CONTAINED IN ACCORDANCE WITH EXPOSURE LEVELS OF INGREDIENTS
SECTION.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
====================== Handling and Storage ======================
Handling and Storage Precautions:TRAIN WELDER TO KEEP HIS/HER FACE AWAY
FROM THE FUME/DUST PLUME.
Other Precautions:PLEASE READ & UNDERSTAND PROD LABEL INFO FOR PROPER
PROC & USE. SEE ANSI Z49.1, "SFTY IN WELDING & CUTTING" & CHAPTER
11 OF "THERMAL SPRAYING", PUBLISHED BY AMERICAN WELDING SOCIETY &
OSHA PUBLICATION 2206 (29 CFR 1910) FOR MORE DETAILS.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:IF THE WORK STATION IS NOT PROPERLY VENTILATED
TO EXHAUST ALL FUMES, VAPORS AND DUSTS BELOW THE RECOMMENDED
EXPOSURE LIMITS, USE A NIOSH APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GEN VENT & LOC EXHST AT WORK SITE TO KEEP ALL
FUMES & DUST OUT OF WORKER'S BRTHG ZONE & GEN AREA.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:EMERGENCY EYEWASH AND DELUGE SHOWER MEETING
ANSI DESIGN CRITERIA .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZ: IGNITE COMBUSTS & FLAMMS. SOME FLUXES & CHEM ACIDS MAY GIVE
OFF HYDROGEN CHLORIDE, PHOSGENE & CHLORINE GASES. CANS, UNDER
PRESS, & FLAMMS MAY EXPLODE. HAZ DECOMP PROD: & FORM FROM INGS LIST
ED. DECOMP PRODS OF NORM OPERATION INCLTHOSE ORIGINATING FROM
VOLATILIZATION, RXN/OXIDATION OF MATLS SHOWN IN (ING 4)
================== Physical/Chemical Properties ==================
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:DURING WELDING, THERMAL SPRAYING &
ALLIED PROCESSES, FUME & GAS DECOMP PRODS GENERATED ARE DIFFERENT
IN PERCENT(SUP DAT)
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSE OF WASTE MATERIAL, POWDERS, GRINDING, OR
FILTER RESIDUES IN AN ENVIRONMENTALLY SENSITIVE MANNER IN
ACCORDANCE WITH FEDERAL, STATE AND LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|