=====================  Product Identification  =====================

MSDS NAME:SILICONE ALKYD COPOLYMER ENAMEL #16187 GRAY
NIIN:01-356-2940
Status Code:A
MSDS Number: CLPRF
=== Responsible Party ===
Company:FARWEST PAINT MANUFACTURING CO
Address:4522 SOUTH 133RD ST
City:TUKWILA
State:WA
ZIP:98168
Country:US
Info Phone Num:206-244-8844
Emergency Phone Num:800-424-9300
Preparer's Name:ERNEST CARTER
Chemtrec Ind/Phone:(800)424-9300
CAGE:6F266
=== Contractor Identification ===
Company:FARWEST PAINT MANUFACTURING CO
Address:4522 SOUTH 133RD ST
Box:City:TUKWILA
State:WA
ZIP:98168
Country:US
Phone:206-244-8844
CAGE:6F266

=============  Composition/Information on Ingredients  =============

Name:MINERAL SPIRITS
CAS:8032-32-4
Code:F
RTECS #:OI6180000
= Wt:31.75
ACGIH TLV:1370 MG/M3;300 PPM

=====================  Hazards Identification  =====================

Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Effects of Overexposure:SKIN: THIS MATERIAL MAY CAUSE IRRITATION.
    SENSITIZATION, OR DEFATTING OF SKIN UPON PROLONGED OR REPEAETD
    CONTACT. INHALATION: EXCESSIVE EXPOSURE TO VAPORS OR SPRAY MIST CAN
    RESULT IN HEADACHE, DIZZINE SS, NAUSEA AND LOSS OF CONSCIOUSNESS.
    EYES: THIS MATERIAL MAY BE AN EYE IRRITANT.

=======================  First Aid Measures  =======================

First Aid:SKIN: WASH WITH SOAP AND WATER. REMOVE AND WASH ANY
    CONTAMINATED CLOTHING BEFORE REUSE. EYES: FLUSH WITH LARGE
    QUANTITIES OF WATER FOR 15 MINUTES AND SEEK MEDICAL ATTENTION.
    SWALLOWING: IF INGESTED DO	NOT INDUCE VOMITING; KEEP PERSON WARM
    AND QUIET AND GET MEDICAL ATTENTION.  INHALATION: REMOVE VICTIM TO
    FRESH AIR IMMEDIATELY. IF RESPIRATORY SYMPTOMS DEVELOP, SEEK
    MEDICAL ATTENTION AT ONCE.

=====================  Fire Fighting Measures  =====================

Flash Point Method:TCC
Flash Point:=41.7C, 107.F
Lower Limits:0.7%
Upper Limits:6.0%
Extinguishing Media:FOAM, CO2, DRY CHEMICAL, OR WATER FOG.
Fire Fighting Procedures:FIREFIGHTERS AND OTHERS EXPOSED TO VAPORS OR
    PRODUCTS OF COMBUSTION SHOULD WEAR SELF CONTAINED BREATHING
    APPARATUS. EVACUATE AREA OF UNPROTECTED PERSONNEL. WEAR PROTECTIVE
    CLOTHING.
Unusual Fire/Explosion Hazard:VAPORS MAY FORM AN EXPLOSIVE MIXTURE IN
    AIR AND  MAY BE IGNITED BY SPARKS, PILOT LIGHTS, ETC.   CLOSED
    CONTAINERSMAY RUPTURE WHEN EXPOSED TO EXTREME HEAT.

==================  Accidental Release Measures  ==================

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION. VENTILATE
    AREA. ABSORB SPILL WITH AN ABSORBENT MATERIAL SUCH AS SAWDUST,
    VERMICULITE OR SAND PLACE MATERIAL INTO A CLOSED CONTAINER. IF
    LARGE SPILL, DIKE  AREA TO PREVE NT THIS MATERIAL FROM ENTERING
    WATER SYSTEMS OR SEWERS. WEAR PROTECTIVE EQUIPMENT DURING CLEANUP.

======================	Handling and Storage  ======================

Handling and Storage Precautions:AVOID PROLONGED OR REPEAETD INHALATION
    OF HEATED VAPORS OR SPRAY MIST. KEEP AWAY FROM HEAT OR OPEN FLAME.
    THIS MATERIAL MAY CAUSE SENSITIZATION, DO NOT GET IN EYES, ON SKIN
    OR CLOTHING. DO NOT ALLOW C ONTAMINATED CLOTHING TO CONTACT SKIN.
    DO NOT WELD ON F   KEEP CONTAINERS CLOSED WHEN NOT IN USE.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:A CANISTER TYPE RESPIRATOR MUST BE WORN TO
    PREVENT THE INHALATION OF VAPORS OR SPRAY MIST WHEN THE TLV OR PEL
    IS EXCEEDED.
Ventilation:GENERAL VENTILATION IS REQUIRED.
Protective Gloves:CHEMICAL RESISTANT NITRILE, NEOPRENE OR RUBBER GLOVES
    REQUIRED.
Eye Protection:WEAR FACE SHIELD OR CHEMICAL GOGGLES.
Other Protective Equipment:WEAR PROTECTIVE CLOTHING TO PREVENT SKIN
    CONTACT.
Work Hygienic Practices:WASH HANDS BEFORE EATING OR SMOKING.
Supplemental Safety and Health

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:307-387 F
Vapor Pres:2.6 MMHG @20 C
Vapor Density:HEAVIER
VOC Pounds/Gallon:340
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NIL
Appearance and Odor:GRAY LIQUID, MILD ODOR
Percent Volatiles by Volume:45%

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDANTS, ACIDS, BASES AND EPOXY HARDENERS
    UNDER UNCONTROLLED CONDITIONS.
Stability Condition to Avoid:HEAT, SPARKS AND OPEN FLAME.
Hazardous Decomposition Products:COMBUSTION CAN YIELD CARBON MONOXIDE
    AND TOXIC VAPORS.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE	IN ACCORDANCE  WITH LOCAL, STATE AND
    FEDERAL AGENCIES.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***