===================== Product Identification =====================
MSDS NAME:SCOTCH-WELD 3501-A GRAY EPOXY ADHESIVE
NIIN:01-107-3981
MSDS Number: BGMDX
=== Responsible Party ===
Company:MINNESOTA MINING ADHESIVE/SEALERS DIV
Address:3M CENTER
City:ST PAUL
State:MN
ZIP:55144-1000
Country:US
Info Phone Num:612-733-1110
Emergency Phone Num:612-733-1110
CAGE:76381
=== Contractor Identification ===
Company:3M MINNESOTA MINING AND MFG CO ADHESIVES SEALERS DIV
Address:3M CTR
Box:City:SAINT PAUL
State:MN
ZIP:55144-1000
Country:US
Phone:800-364-3577/651-737-6501(24 HOURS)
CAGE:04963
Company:MINNESOTA MINING AND MFG CO, DBA 3M
Address:3M CENTER BLDG 224-5S-04
Box:City:SAINT PAUL
State:MN
ZIP:55144-1000
Country:US
Phone:866-556 5712 / 612-733-1110
CAGE:76381
============= Composition/Information on Ingredients =============
Name:MERCAPTN POLYMER
Fraction by Wt: 50-60%
Name:TALC (POWDER), (ASBESTOS FREE), TALCUM; HYDROUS MAGNESIUM
SILICATE
CAS:14807-96-6
RTECS #:WW2710000
Fraction by Wt: 30-40%
OSHA PEL:20 MPPCF
ACGIH TLV:2 MG/CUM (RESP DUST)
Name:POLYAMIDE OF C18 FATTY ACID PRIMERS & TETA; POLYAMIDE RESIN
*92-2*
CAS:68410-23-1
Fraction by Wt: 10-20%
Name:2,4,6-TRI(DIMETHYLAMINOMETHYL)PHENOL, DMP-30
CAS:90-72-2
RTECS #:SN3500000
Fraction by Wt: 1-10%
ACGIH TLV:5 PPM
Name:SILICON DIOXIDE
CAS:7631-86-9
RTECS #:VV3100000
Fraction by Wt: 1-10%
OSHA PEL:80 MG/CUM
ACGIH TLV:0.2 MG/CUM
===================== Hazards Identification =====================
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: IRRITATION, PERMANENT DAMAGE,
REDNESS, SMARTING, & TEARING. SKIN: IRRITATION, ABSORPTION, &
ALLERGIC REACTION. INHALATION: NOSE & THROAT IRRITATION,
DROWSINESS, SLURRED SPEECH, HEADACHE, NAUSEA, DIZZINESS, &
RESPIRATORY SYSTEM IRRITATION. INGESTION: DIGESTIVE SYSTEM
IRRITATION.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:EYES: IRRITATION, PERMANENT DAMAGE, REDNESS,
SMARTING, & TEARING. SKIN: IRRITATION, ABSORPTION, & ALLERGIC
REACTION. INHALATION: NOSE, & THROAT IRRITATION, DROWSINESS,
SLURRED SPEECH, HEADACHE, NAUSEA , DIZZINESS, & RESPIRATORY SYSTEM
IRRITATION. INGESTION: DIGESTIVE SYSTEM IRRITATION.
======================= First Aid Measures =======================
Eyes: FLUSH W/PLENTY OF WATER FOR AT LEAST 10 MINS. SKIN:
WASH W/SOAP & WATER. INHALATION: REMOVE TO FRESH AIR. INGESTION:
DRINK TWO GLASSES OF MILK OR WATER. OBTAIN MEDICAL ATTENTION IN ALL
CASES.
===================== Fire Fighting Measures =====================
Flash Point:>200F
Extinguishing Media:CO2, FOAM, DRY CHEMICAL, OR WATER
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS.
================== Accidental Release Measures ==================
Spill Release Procedures:VENTILATE AREA. COLLECT SPILLED MATERIAL.
PLACE IN DOT APPROVED MEATL CONTAINER & SEAL.
====================== Handling and Storage ======================
Handling and Storage Precautions:FOR INDUSTRIAL/PROFESSIONAL USE ONLY.
USE ONLY IN WELL VENTILATED AREAS. AVOID BREATHING VAPOR. DON'T
RECIRCULATE EMISSIONS INTO WORKROOM AIR.
Other Precautions:KEEP CONTAINER CLOSED WHEN NOT IN USE. KEEP OUT OF
REACH OF CHILDREN. AVOID EYE CONTACT W/OR BREATHING DUST FROM
GRINDING, SANDING, OR CUTTING OPERATIONS ON THE CURED PRODUCT.
DON'T CURE UP A MASS LAR GER THAN 50 GRAMS TO PREVENT EXOTHERM.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:DUST MASK
Ventilation:RECOMMENDED
Protective Gloves:IMPERVIOUS
Eye Protection:CHEMICAL GOGGLES, SAFETY GLASSES
Work Hygienic Practices:REMOVE/WASH CONTAMINATED CLOTHING BEFORE REUSE.
Supplemental Safety and Health
WHEN TWO COMPONENTS (PART B & PART A) ARE COMBINED, AVOID HEAT
CONDITIONS WHICH CAUSE PREMATURE REACTION (EXOTHERM) W/PRODUCTION
OF INTENSE HEAT & SMOKE. HEAT IS GENERATED DURING CURE.
================== Physical/Chemical Properties ==================
HCC:N1
Spec Gravity:1.4
Solubility in Water:INSOLUBLE
Appearance and Odor:BLACK PASTE W/EPOXY ODOR
Percent Volatiles by Volume:0%/WT
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
Stability Condition to Avoid:EXCESSIVE HEAT, FLAME
Hazardous Decomposition Products:CO, CO2, NITROGEN, SMOKE PARTICLES,
SULFUR DIOXIDE
Conditions to Avoid Polymerization:HEAT, DON'T CURE MASS >50 GRAMS.
==================== Disposal Considerations ====================
Waste Disposal Methods:MIX PART A & B. COMPLETELY CURE & DISPOSE OF
FULLY CURED WASTE PRODUCT IN SANITARY LANDFILL. INCINERATE UNCURED
BULK PRODUCT AFTER MIXING W/FLAMMABLE MATERIAL IN
INDUSTRIAL/COMMERCIAL FACILITY. DISPOS E OF IN ACCORDANCE
W/FEDERAL/STATE/LOCAL LAWS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|