===================== Product Identification =====================
MSDS NAME:CONTACT ADHESIVES LW 270,400
NIIN:00B230006
MSDS Number: BBBZC
=== Responsible Party ===
Company:RALPH WILSON PLASTICS CO.
Address:600 GENERAL BRUCE DRIVE
City:TEMPLE
State:TX
ZIP:76501-5199
Country:US
Info Phone Num:817778-2711
Emergency Phone Num:180424-9300
CAGE:20706
=== Contractor Identification ===
Company:RALPH WILSON PLASTICS CO
Box:City:TEMPLE
State:TX
ZIP:76503-6110
Country:US
Phone:817-778-2711
CAGE:20706
============= Composition/Information on Ingredients =============
Name:NEOPRENE
CAS:9010-98-4
RTECS #:EI9660000
Name:PHENOLIC RESINS
Name:KETONENS(MEK,ACETONE)
CAS:78-98-3
OSHA PEL:200/1000 PPM
ACGIH TLV:200/750 PPM
Name:TOLUENE (SARA III)
CAS:108-88-3
RTECS #:XS5250000
OSHA PEL:200 PPM/150 STEL
ACGIH TLV:50 PPM; 9293
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
Name:HEXANE (N-HEXANE)
CAS:110-54-3
RTECS #:MN9275000
OSHA PEL:500 PPM
ACGIH TLV:50 PPM; 9293
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB
Name:MAGNESIUM OXIDE
CAS:1309-48-4
RTECS #:OM3850000
OSHA PEL:15 MG/M3 PARTICULATE
ACGIH TLV:10 MG/M3;TDUST; 9293
===================== Hazards Identification =====================
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:IRRITATION TO EYES,MUCOUS
MEMBRANES,SKIN.AT HIGHER CONCENTRATIONS,NARCOSIS MAY RESULT.
Effects of Overexposure:PROLONGED INHALATION MAY CAUSE
HEADACHES,NAUSEA,SHORTNESS OF BREATH,DROWSINESS.
======================= First Aid Measures =======================
First Aid:INHALATION:REMOVE VICTIM TO FRESH AIR.USE APPROPRIATE
RESPIRATOR IF NECESSARY.INTERNAL:CALL PHYSICIAN IMMEDIATELY.DO NOT
INDUCE VOMITING.
===================== Fire Fighting Measures =====================
Flash Point Method:TOC
Flash Point:15F
Lower Limits:2%
Upper Limits:13%
Extinguishing Media:CO2,FOAM,SAND
Fire Fighting Procedures:ALL SOLVENTS ARE FLAMMABLE.
Unusual Fire/Explosion Hazard:NEOPRENE GIVES OFF HC1 WHEN BURNED.
================== Accidental Release Measures ==================
Spill Release Procedures:APPLY SAWDUST OR SIMILAR MATERIAL TO SPILL
AREA TO CONTAIN.SCOOP UP SPILL AND PUT INTO SUITABLE CONTAINER.IF
NECESSARY,USE SOLVENT TO REMOVE REMAINDER OF ADHESIVE.
====================== Handling and Storage ======================
Handling and Storage Precautions:AVOID CONTACT WITH EYES OR SKIN.AVOID
BREATHING OF VAPORS.
Other Precautions:STORE AND USE ONLY IN WELL-VENTILATED AREAS:ALL
ELECTRICAL EQUIPMENT IN AREA SHOULD BE EXPLOSION-PROOF.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:ORGANIC VAPOR,FULL-FACE RESPIRATOR-ONLY IF NOT
O2 DEFICIENT.
Ventilation:MECHANICAL PREFERRED.
Protective Gloves:NEOPRENE SUGGESTED.
Eye Protection:TO BE USED WHEN SPRAYING.
Other Protective Equipment:NONE
Work Hygienic Practices:APPLY GOOD HOUSEKEEPING PROCEDURES.
Supplemental Safety and Health
================== Physical/Chemical Properties ==================
Boiling Pt:B.P. Text:132-143
Vapor Pres:185
Spec Gravity:0.822
Evaporation Rate & Reference:7.7
Appearance and Odor:VISCOUS LIQUID,STRONG KETONE ODOR.
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
Stability Condition to Avoid:SPARKS AND OPEN FLAMES
Hazardous Decomposition Products:NONE
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSE OF AS SOLID WASTE.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|