=====================  Product Identification  =====================

MSDS NAME:CONCRESIVER 1170,PART B
NIIN:00N009901
MSDS Number: BHFXN
=== Responsible Party ===
Company:ADHESIVE ENGINEERING COMPANY
Address:1411 INDUSTRIAL ROAD
City:SAN CARLOS
State:CA
ZIP:94070
Info Phone Num:415-592-7900
Emergency Phone Num:415-592-7900;800-424-9300-CHEMTREC
CAGE:17433
=== Contractor Identification ===
Company:ADHESIVE ENGINEERING CO.
Address:1411 INDUSTRIAL CO.
Box:2449
City:SAN CARLOS
State:CA
ZIP:94070
Country:US
CAGE:17433

=============  Composition/Information on Ingredients  =============

Name:DIETHYLENE TRIAMINE
CAS:111-40-0
RTECS #:IE1225000
Fraction by Wt: <30%
Other REC Limits:N/K 
OSHA PEL:1 PPM
ACGIH TLV:S, 1 PPM; 9192

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:SEE SUPP DATA
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:DIETHYLENE TRIAMINE IS A STRONG
    SENSITIZER.PROLONGED OR REPEATED EXPOSURE MAY CAUSE SKIN AND EYE
    BURNS AND/OR SENSITIZATION.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:EYES AND SKIN:CORROSIVE.INGESTION AND
    INHALATION:N/K .
Medical Cond Aggravated by Exposure:N/K 

=======================  First Aid Measures  =======================

Eyes:HOLDING EYELIDS APART FLUSH W/ H*2O FOR AT LEAST 15
    MIN.GET MED ATTN.SKIN:WASH W/ SOAP & H*2O OR WATERLESS HAND CLEANER
    FOLLOWED BY SOAP & H*2O.CLEAN CLTHG BEFORE REUSE.IF IRRITATION
    PERSISTS,GET  MED ATTN.INGEST:DDO NOT INDUCE VOMIT.IF
    CONSCIOUS,GIVE LRG AMTS OF H*2O OR MILK IF IMMED AVAILABLE.CALL
    MD.INHAL:REMOVE TO FRESH AIR.GIVE O*2 IF BRTHG IS DIFF & ART RESP
    IF NOT BRTHG.GET MED ATTN.

=====================  Fire Fighting Measures  =====================

Flash Point Method:PMCC
Flash Point:>200F,93C
Extinguishing Media:WATER FOG,FOAM,CARBON DIOXIDE,DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .COOL EXPOSED CONTAINERS WITH WATER STREAM.
Unusual Fire/Explosion Hazard:THERMAL DECOMPOSITION OR BURNING MAY
    PRODUCE CARBON MONOXIDE AND/OR CARBON DIOXIDE,NITROGEN OXIDES AND
    AMMONIA.

==================  Accidental Release Measures  ==================

Spill Release Procedures:WEAR APPRVD RESP & APPROP CLTHG.IF POSS,SHUT
    OFF LEAK.IF WARM,REMOVE LIQ BY PUMPING INTO SALVAGE DRUMS.IF COOL &
    NON-PUMPABLE,SHOVEL & SCRAPE INTO SALVAGE DRUMS.SOAK UP RESIDUE &
    SMALL SPILLS W/ ABSOR B MATL SUSH AS CLAY.PUT INTO TIGHT CONTAINER.
Neutralizing Agent:N/K .

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN A COOL PLACE IN TIGHT
    CONTAINERS.AVOID BREATHING VAPORS OF HEATED MATERIAL.AVOID ALL
    PERSONAL CONTACT.
Other Precautions:IF A SOLVENT IS USED FOR CLEANING,TANK PROPER
    PRECAUTIONS AGAINST FIRE AND PERSONAL OVEREXPOSURE.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR
    EXPOSURE OF CONCERN .
Ventilation:LOCAL AND GENERAL VENTILATION NECESSARY TO KEEP AIR
    CONCENTRATION BELOW TLV .
Protective Gloves:PRODUCT RESISTANT RUBBER GLOVES.
Eye Protection:CHEM WORKERS GOGGLES,FACESHIELD .
Other Protective Equipment:PROTECTIVE CLOTHING AS REQUIRED TO PREVENT
    SKIN CONTACT.
Work Hygienic Practices:WASH WITH SOAP AND WATER BEFORE
    EATING,DRINKING,SMOKING OR USING TOILET FACILITIES.LAUNDER CONTAM
    CLOTHING BEFORE REUSE.
Supplemental Safety and Health
LD50-LC50 MIX:LD50 ORAL>1000 MG/KG.TOXIC AS DEFINED IN 16CFR
    1500.3.LD50 SKIN >800 MG/KG-TOXIC AS DEFINED IN 16CFR 1500.3.LC50
    INHAL-NOT DETERMINED.

==================  Physical/Chemical Properties  ==================

Melt/Freeze Pt:M.P/F.P Text:N/K 
Decomp Temp:Decomp Text:N/K 
Vapor Density:>1 (AIR=1)
Spec Gravity:0.974 (WATER=1)
Solubility in Water:NEGLIGIBLE
Appearance and Odor:CLEAR AMBER.
Percent Volatiles by Volume:NEGLIG

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS,OXIDIZING AGENTS.EPOXY RESIN UNDER UNCONTROLLED
    CONDITIONS.
Stability Condition to Avoid:N/K 
Hazardous Decomposition Products:THERMAL DECOMPOSITION OR BURNING MAY
    PRODUCE CARBON MONOXIDE AND/OR CARBON DIOXIDE,NITROGEN OXIDES AND
    AMMONIA.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSAL MUST BE IN ACCORDANCE WITH
    FEDERAL,STATE AND LOCAL REGULATIONS .REMOVE TO WASTE DISPOSAL
    FACILITY OPERATING IN COMPLIANCE WITH ALL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***