===================== Product Identification =====================
MSDS NAME:WHITE LEAD
NIIN:00F005594
MSDS Number: BBSVM
=== Responsible Party ===
Company:HAMMOND LEAD PRODUCTS, INC/HAMMOND, IN 46320
Emergency Phone Num:(219) 931-9360
CAGE:84721
=== Contractor Identification ===
Company:HAMMOND LEAD PRODUCTS INC HALSTAB DIV
Address:3100 MICHIGAN AVE
Box:6408
City:HAMMOND
State:IN
ZIP:46325-6408
Country:US
CAGE:84721
============= Composition/Information on Ingredients =============
Name:LEAD CARBONATE (OSHA PEL FROM 29CFR 1910.1025)
CAS:598-63-0
RTECS #:OF9275000
Fraction by Wt: 100%
OSHA PEL:0.05 MG/M3 (PB)
ACGIH TLV:0.15 MG/M3 (PB);8990
===================== Hazards Identification =====================
Effects of Overexposure:WORST CASE SITUATIONS COULD RESULT IN
CONVULSIONS, STUPOR, COMA AND ENCEPHALOPATHY.
======================= First Aid Measures =======================
First Aid:INHALATION: REMOVE FROM EXPOSURE. GET MEDICAL ATTENTION IF
EXPERIENCING EFFECTS OF ACUTE OVEREXPOSURE. INGESTION: INDUCE
VOMITING IN A CONSCIOUS INDIVIDUAL. GET MED ATT. CALL PHYSICIAN.
SKIN: WASH W/S OAP & WATER. EYES: FLUSH W/WATER. GET MED ATT.
===================== Fire Fighting Measures =====================
Extinguishing Media:WATER FOG OR FLOOD, CO2 & DRY CHEMICAL
Fire Fighting Procedures:WEAR FULL BODY PROTECTIVE CLOTHING/FULL
FACEPIECE, SCBA.
Unusual Fire/Explosion Hazard:FUME, VAPOR, AND DUST MAY OCCUR AND ARE
CONSIDERED TOXIC & RESPIRATORY IRRITANTS.
================== Accidental Release Measures ==================
Spill Release Procedures:CLEAN THE AREA OF SPILL, RETURNING ALL
MATERIAL POSSIBLE TO CONTAINER. WEAR GLOVES/GGLES/RESP. DON'T
BREATHE OR INGEST DUST. FOR A SMALL SPILL, USE A VACUUMDON'T BROOM
SWEEP. EXCESS MATERIAL SHOULD BE STORED IN DRY CONTAINERS
FODISPOSAL
====================== Handling and Storage ======================
Handling and Storage Precautions:DON'T INHALE OR SWALLOW DUST. WASH
THOROUGHLY AFTER HANDLING. DON'T SMOKE, EAT, OR APPLY COSMECS IN
WORK AREA.
Other Precautions:KEEP LEAD MATERIALS AWAY FROM FEED & FOOD PRODUCTS.
KEEP AWAY FROM CHILDREN. DON'T REUSE CONTAINERS. THIS PRODUCT IS
INTENDEFOR INDUSTRIAL USE ONLY. DON'T WEAR ANY PART OF WORK
CLOTHING.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:RESPIRATOR MUST BE WORN IF TLV IS EXCEEDED.
Ventilation:PROVIDED WHERE EXPOSURES EXCEED PEL OR TLV SPECIFIED IN.
Protective Gloves:RECOMMENDED
Eye Protection:RECOMMENDED
Other Protective Equipment:HARD HAT/SAFETY BOOTS/OTHER SAFETY EQUIPMENT
SHOULD BE WORN.
Supplemental Safety and Health
MSDS DATE: 03/01/85. MELTING POINT: 400F-750F.
================== Physical/Chemical Properties ==================
Spec Gravity:6.8
Solubility in Water:INSOLUBLE
Appearance and Odor:WHIE POWDER; ODORLESS.
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
HYDROGEN PEROXIDE, STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:DON'T HEAT IN PRESENCE OF AL, NA, TI.
Hazardous Decomposition Products:HIGH TEMPS OR FIRE MAY PRODUCE FUME,
VAPOR, OR DUST.
Conditions to Avoid Polymerization:LOSES CO2 AT 375F; DECOMPOSES TO
LITHARGE AT 750F. 50F.
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSAL OF WASTE/HAZARDOUS MATERIAL SHOULD BE
HANDLED IN A MANNER WHICH COMPLIES W/LOCAL, STATE & FEDERAL
ENVIRONMENTAL PROTECTION AGENCY REGULATIONS. IT'S PREFERABLE TO
SEND WASTE MATERIAL TO A RECY CLING FACILITY WHICH IS APPROVED BY
STATE & EPA.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|