=====================  Product Identification  =====================

MSDS NAME:CONCRESIVE(R) 1160 PART A
NIIN:00N010977
MSDS Number: BHVLH
=== Responsible Party ===
Company:ADHESIVE ENGINEERING COMPANY
Address:1411 INDUSTRIAL ROAD
City:SAN CARLOS
State:CA
ZIP:94070
Info Phone Num:415-592-7900
Emergency Phone Num:415-592-7900;800-424-9300 CHEMTREC
CAGE:17433
=== Contractor Identification ===
Company:ADHESIVE ENGINEERING CO.
Address:1411 INDUSTRIAL CO.
Box:2449
City:SAN CARLOS
State:CA
ZIP:94070
Country:US
CAGE:17433

=============  Composition/Information on Ingredients  =============

Name:CONTAINS NO HAZARDOUS MATERIAL AS DEFINED BY OSHA OR ACGIH
    (MFG).
Other REC Limits:N/K 
OSHA PEL:N/K 
ACGIH TLV:N/K 

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:LD50 ORAL >5000 MG/KG,(SEE SUPP DATA)
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:SEE SIGNS AND SYMPTOMS OF
    OVEREXPOSURE.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:EYES:NOT A PRIMARY IRRITANT AS DEFINED IN
    16CFR1500.42.PROLONGED OR REPEATED CONTACT MAY CAUSE EYE
    IRRITATION/SENSITIZATION.SKIN:NOT A PRIMARY IRRITANT AS DEFINED IN
    16CFR1500.41.PROLONGED OR REPEATED	SKIN EXPOSURE MAY CAUSE SKIN
    IRRITATION/SENSITIZATION.INGESTION/INHALATION:N/K .
Medical Cond Aggravated by Exposure:N/K 

=======================  First Aid Measures  =======================

Eyes:FLUSH W/ WATER FOR AT LEAST 15 MIN WHILE HOLDING EYELIDS
    OPEN.GET MED ATTN.SKIN:WASH W/ SOAP & WATER OR WATERLESS HAND
    CLEANER FOLLOWED BY SOAP & WATER.IF IRRIT PERSISTS,GET MED
    ATTN.INGEST:INDUC E VOMIT BY STICKING FINGER DOWN THROAT OR BY
    GIVING SOAPY OR STRONG SALTY WATER TO DRINK.REPEAT UNTIL VOMIT IS
    CLEAR.CALL MD.NEVER GIVE ANYTHING BY MOUTH TO UNCON
    PERSON.INHAL:REMOVE TO (SEE SUPP)

=====================  Fire Fighting Measures  =====================

Flash Point Method:PMCC
Flash Point:>200F,93.33C
Extinguishing Media:WATER FOG,FOAM,CO*2,DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
    PROTECTIVE EQUIPMENT .COOL EXPOSED CONTAINERS WITH WATER STREAM.
Unusual Fire/Explosion Hazard:NO UNUSUAL HAZARDS.HAZARDOUS
    DECOMPOSITION PRODUCTS:THERMAL DECOMPOSITION MAY PRODUCE
    CO,ALDEHYDES,AND ACIDS FROM INCOMPLETED COMBUSTION.

==================  Accidental Release Measures  ==================

Spill Release Procedures:WEAR APPROVED RESP,APPROP CLTHG.SHUT OFF LEAK
    IF POSS SAFELY.IF WARM,REMOVE LIQ BY PUMPING INTO SALVAGE DRUMS.IF
    COOL,SHOVEL/SCRAPE INTO SALVAGE DRUMS.SOAK UP RESIDUE/SML SPILL W/
    ABSORB MATL (CLAY),P UT INTO TIGHT CONTR.IF SOLVENT USED,TAKE PREC.
Neutralizing Agent:N/K 

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN COOL PLACE IN TIGHT
    CONTAINERS.AVOID BREATHING VAPORS OF HEATED MATERIAL.AVOID ALL
    PERSONAL CONTACT.
Other Precautions:FOR INDUSTRIAL USE ONLY.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR
    EXPOSURE OF CONCERN .
Ventilation:LOCAL AND GENERAL VENTILATION NECESSARY TO KEEP AIR
    CONCENTRATION BELOW LEVEL OF CONCERN .
Protective Gloves:PRODUCT RESISTANT RUBBER.
Eye Protection:CHEM WORK GOGG ,FACESHIELD.
Other Protective Equipment:PROTECTIVE CLOTHING AS REQUIRED TO PREVENT
    SKIN CONTACT.
Work Hygienic Practices:WASH W/ SOAP & WATER BEFORE
    EATING,DRINKING,SMOKING OR USING TOILET FACILITIES.LAUNDER CONTAM
    CLOTHING BEFORE REUSE.
Supplemental Safety and Health
LD50-LC50 MIX:LD50 SKIN ABSORPTION >2000 MG/KG;LC50 INHALATION NO
    DEATHS IN SATURATED AIR FOR 8 HRS.FIRST AID PROC:FRESH AIR &
    PROVIDE OXYGEN IF BREATHING IS DIFFICULT.GIVE ARTF RESP IF NOT
    BREATHING. GET MED ATTN.

==================  Physical/Chemical Properties  ==================

Melt/Freeze Pt:M.P/F.P Text:N/K 
Decomp Temp:Decomp Text:N/K 
Vapor Density:>1 (AIR=1)
Spec Gravity:1.17 (WATER=1)
Solubility in Water:NEGLIGIBLE
Appearance and Odor:TRANSPARENT AMBER

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
CAN REACT VIGOROUSLY WITH EXCESS HARDENER & WITH STRONG OXIDIZING
    AGENTS AND STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:N/K 
Hazardous Decomposition Products:THERMAL DECOMPOSITION MAY PRODUCE
    CO,ALDEHYDES,AND ACIDS FROM INCOMPLETED COMBUSTION.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSAL MUST BE IN ACCORDANCE WITH
    FEDERAL,STATE AND LOCAL REGULATIONS .REMOVE TO A WASTE DISPOSAL
    FACILITY OPERATING IN COMPLIANCE WITH STATE & LOCAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***