Material Safety Data Sheet
I. Chemical Product and Company Identification:
Product Description: Exterior Latex Deep Tone, Exterior Latex Flat White
Stock Numbers: 10-0050-00; 10-1430-00 & 10-1440-00
HMIS CODES: H-1* Date Prepared: 8-22-07
F-1 Supercedes: 12-16-2002
R-0
P-x (see section VIII)
Company: North Carolina Department of Correction Enterprise Paint Plant
Address: 2465 US 70 West
Smithfield, NC 27577
Telephone: Product Information: (919) 989-8695
Emergency: CHEMTREC: 1-800-424-9300
Contact for Technical Information: Steve Jacobson (919) 989-8695
II. Composition/Information on Ingredients:
Component CAS # Percent by weight NCOSH PEL ACGIH TLV
*Calcium carbonate 1317-65-3 <18 15 mg/m³ 10 mg/m³
(total dust)
5 mg/m³
(respirable dust)
*Cellulose 9004-62-0 <0.3 15mg/m³ 10 mg/m³
(total dust)
5 mg/m³
(respirable dust)
*Diatomaceous earth Proprietary <6 6 mg/m³ 10 mg/m³
(total dust)
Ester alcohol 25265-77-4 <1 NE NE
[2,2,4-trimethyl-1,3-pentanediol monoisobutyrate]
*Propylene glycol 57-55-6 <6 NE NE
*Silica (amorphous) 112926-00-8 <1.1 6 mg/m³ 10 mg/m³
*Silica (crystalline silica) 14808-60-7 <0.2 10 mg/m³ 0.1 mg/m³
5 mg/m³
(respirable dust)
*Titanium dioxide 13463-67-7 3-16 10 mg/m³ 10 mg/m³
(total dust) (total dust)
5 mg/m³
(respirable dust)
Acrylic polymers Proprietary <20 NE NE
Water 7732-18-5 <42 NE NE
*Zinc oxide 1314-13-2 <3 10 mg/m³ 10 mg/m³
(total dust) (total dust)
*Zinc pyrithione 13464-41-7 <0.4 NE NE
*These substances are hazardous chemicals as defined by the Hazard Communication Standard (29 CFR 1910.1200)
NE: Not Established
1
III. Hazard Identification:
Aqueous fluids have a mild odor. They may be harmful if swallowed or if concentrated mists or vapors are inhaled.
They may be harmful if absorbed through the skin. For large spills, emergency responders should wear chemical
resistant coveralls, boots, gloves, chemical resistant goggles, and appropriate respiratory protection in poorly
ventilated areas. Responders should remove any source of ignition, limit access, ventilate spill area, and absorb spill
material with inert, noncombustible material, or transfer to a suitable container for reuse or disposal. See sections V,
VI, and XIII.
Potential health effects and primary routes of entry:
Eye contact: Eye contact may cause irritation, including stinging, tearing, and redness of the conjunctiva
(linings of inner eyelid).
Skin: Skin contact can cause irritation with discomfort and redness, and may result in absorption of potentially
harmful amounts of the material. Symptoms may include redness, burning, and dermatitis.
Ingestion: Ingestion may cause fatigue, drowsiness, dizziness, headache, nausea, vomiting, diarrhea, central
nervous system depression, respiratory problems, liver damage, kidney damage, respiratory failure, cardiac failure,
loss of consciousness, and blindness.
Inhalation: Irritation of the respiratory tract. Prolonged exposure may lead to dizziness, lightheadedness,
headache, gastrointestinal disturbances, coughing, apathy, nausea, vomiting, central nervous system depression,
respiratory problems, narcosis, difficulty in breathing, blood abnormalities, kidney damage, and loss of
consciousness. Signs and symptoms of exposure include dizziness, incoordination, drunkenness, stupor, and/or
lightheadedness.
Chronic Effects/Carcinogenicity:
Long term overexposure to sanding dusts via inhalation may cause slight lung fibrosis, silicosis, and talcosis (a
pulmonary fibrosis which could lead to severe and permanent damage to the lungs). Long term exposure to dusts
may also cause other lung disorders, conjunctivitis, and pneumoconiosis. Persons with impaired pulmonary function
may be more susceptible to the effects of breathing dusts.
These listed products contain titanium dioxide and silica, which is a natural impurity in titanium dioxide. Titanium
dioxide (TiO2) and silica, crystalline-quartz showed carcinogenic effects when large doses were administered to rats
via inhalation. Silica-crystalline quartz also showed carcinogenic effects when large doses were administered into
the trachea of rats. All of these ingredients showed carcinogenic effects when large quantities of the dust or powder
were inhaled or implanted in the body. However, inhalation of dusts from these materials is not an expected form of
exposure from use of these listed products.
These products also contain calcium carbonate that typically contains crystalline silica (quartz sand) above 0.1% as a
naturally occurring impurity. The International Agency for Research on Cancer (IARC) has concluded that
“crystalline silica inhaled in the form of quartz or cristobalite from occupational sources is carcinogenic to humans
(Group I).� It also noted that carcinogenicity was not detected in all industrial circumstance studies, and may be
dependent on external factors affecting its biological activity or distribution of its polymorphs. Exposure to
respirable silica has also been associated with silicosis, scleroderma, and nephrotoxicity. These pigment solids are
bound within the acrylic vehicle for these listed products, and overexposure is not expected.
Natural diatomaceous earth (Kieselguhr) contains small quantities (typically <1%) of crystalline silica which is a
known cause of silicosis, a progressive, sometimes fatal lung disease. In a 1997 monograph (Volume 68, “Silica,
Some Silicates, Coal Dust and Para-Aramid Fibrils�), the International Agency of Research on Cancer (IARC) has
classified “inhaled crystalline silica from occupational sources: in Group 1 as a substance “carcinogenic to humans.�
In making the overall evaluation, the IARC Working Group noted that “There is inadequate evidence in
experimental animals for the carcinogenicity of uncalcined diatomaceous earth.� It further noted that “There is
inadequate evidence in humans for the carcinogenicity of amorphous silica� and therefore it was rated as “not
classified as to its carcinogenicity to humans (Group 3)�. Natural diatomaceous (earth) is predominately amorphous
silica. Inhalation of dust in excess of the Threshold Limit Value (TLV) recoomended by the American Conference
of Governmental Industrial Hygienists (ACGIH) for an extended number of years may cause pneumoconiosis.
Pneumoconiosis is a disabling lung disease which may be progressive and, on rare occasions, may ultimately be
2
fatal. Diatomaceous earth exists in some formulations of exterior flat latex coatings (0-3%). This flatting agent is
bound by the acrylic vehicle and overexposure is not expected.
Propylene glycol was shown to cause reproductive and teratogenic effects in experiments with laboratory animals
when they were injected with large doses. Propylene glycol was also shown to be mutagenic according to test tube
(in vitro) assays when tested on human and non-human cells.
For a summary of the toxicology data from which this evaluation was made, please refer to Section XI.
IV. First Aid Measures:
Eye contact: Flush immediately with large amounts of water for at least 20 minutes. Eyelids should be held
away from eyeballs to ensure thorough rinsing. If irritation or other effects persist, obtain medical treatment
immediately.
Ingestion: If swallowed, give 2 glasses of water to drink. Call a physician immediately. Do not induce
vomiting unless directed to do so by medical personnel. Do not leave person unattended. Never give anything by
mouth to an unconscious person.
Inhalation: Move victim to fresh air and administer artificial respiration if not breathing. Trained personnel
should give oxygen if breathing is difficult. Keep person warm and quiet. Get medical attention immediately.
Skin contact: Wash off quickly with plenty of water, then soap and water. Remove any contaminated clothing.
Seek medical attention if symptoms occur. Wash contaminated clothing before reuse.
Medical conditions aggravated by exposure: Ingredients have been reported to aggravate pre-existing eye,
respiratory, kidney, liver, and nervous system disorders. Overexposure to sanding dusts may aggravate certain pre-
existing upper respiratory disorders, such as bronchitis, emphysema, and asthma. Exposure to dust may also
aggravate pre-existing eye conditions.
V. Fire Fighting Measures:
Flash Point: >228Ëš F (for propylene glycol)
Flammable or explosive limits:
None determined for these products.
LFL: 0.62 % (by volume for ester alcohol)
UFL: 4.24 % (by volume for ester alcohol)
Extinguishing media: Use extinguishing media appropriate for surrounding fire. Water may be used to keep
fire-exposed containers cool until the fire is extinguished.
Fire & Explosion Hazards: No special fire hazards are known to be associated with these products. May
decompose under fire conditions emitting irritating and/or toxic gases. Closed containers may burst and material
can splatter above 212Ëš F. Dried product can burn. Closed containers may burst if exposed to extreme heat or fire.
Toxic carbon monoxide, carbon dioxide, acrylic monomers, and other unidentified toxic and /or irritating
compounds will form upon combustion. May decompose under fire conditions emitting irritating and/or toxic gases.
Fire fighting equipment: Exposed firefighters should use NIOSH/MSHA approved self-contained breathing
apparatus (SCBA) with a full face piece under positive pressure and chemical resistant protective equipment when
entering areas where potential for exposure to vapors or products exists. Refer to Section VIII for further
information.
VI. Accidental Release Measures:
Large Spill:
Isolate hazard area and deny entry to unnecessary or unprotected personnel. Wear impervious gloves, clothing, and
safety goggles. In poorly ventilated or low-lying areas, a self-contained breathing apparatus may be required.
Contain spilled liquid with sand, earth, or absorbent. Place in a polypropylene or lined metal disposal container.
Avoid runoff into storm sewers and ditches that lead to waterways. Dispose of waste properly (see Section XIII).
Small Spill:
Wear protective gloves and safety goggles. Absorb or mop up material immediately and place in a polypropylene or
lined metal disposal container.
3
Contact CHEMTREC (800-424-9300) for technical advice and assistance related to chemical emergencies involving
this product.
VII. Handling and Storage:
Handling: Do not get in eyes, on skin, or on clothing. Avoid breathing mist or vapors. Do not taste or
swallow. Keep out of reach of children. Use only with adequate ventilation. Wash thoroughly after handling,
especially before eating or smoking. Avoid conditions that result in formation of inhalable particulate such as
spraying or abrading (sanding) painted surfaces. If such conditions cannot be avoided, use appropriate respiratory
protection as directed in Section VIII. Do not apply to hot metals or surfaces.
Storage: Do not store above 100Ëš F. Keep containers in a well-ventilated area and closed when not in use.
Keep away from heat and open flame. Keep from freezing. Keep containers tightly closed and upright when not in
use. Keep this and all chemicals out of the reach of children.
VIII. Exposure Controls / Personal Protection:
Ventilation: Provide sufficient mechanical or local exhaust ventilation to maintain vapor, mist, or dust
concentrations below exposure limits. Open windows and doors, or use some other means to permit fresh air entry
during application and drying indoors.
Respiratory Protection: None required if airborne concentrations are maintained below exposure limits. A
NIOSH/MSHA approved air-purifying respirator with an ammonia/methylamine cartridge and dust/mist filters may
be permissible under circumstances where concentrations are expected to exceed exposure limits. Protection
provided by air-purifying respirators is limited. Use NIOSH/MSHA approved self contained breathing apparatus in
positive pressure mode if there is a reasonable possibility for harmful exposure to vapors or mists (e.g. during large
spill response operations or fighting a fire involving these product(s), or for entry into unknown concentrations or
immediately dangerous to life or health conditions). If sanding is done, wear a NIOSH-approved particulate
respirator to avoid breathing sanding dust. All respiratory protection should be in accordance with OSHA
regulations in 29 CFR 1910.134.
Protective Gloves: Use chemical resistant non-chlorinated rubber or neoprene gloves to prevent skin contact.
Eye Protection: Avoid eye contact. Chemical splash goggles are recommended. Contact lenses must not be worn.
Provide an ANSI-approved eye wash station in the work area.
Other Protective Equipment: Depending on conditions or use, protective clothing may be required to avoid
contaminating regular clothing and to prevent skin contact.
IX. Physical and Chemical Properties:
Appearance: white milky color (color may vary if tinted)
Odor: mild odor.
Boiling Point: 100Ëš Celsius
Solubility in Water: dilutable
Specific Gravity: 1.2 g/ml (Exterior Latex Flat Deep Tone) & 1.3 g/ml (Exterior Latex Flat White)
pH: not determined
Evaporation Rate: slower than butyl acetate (n-butyl acetate = 1)
VOC Standard: Max VOC's < 250 grams/liter (Exterior flat coatings)
Viscosity: 85-100 K.U.
Vapor Pressure: 17 mm Hg @ 68Ëš F (Water)
Vapor Density greater than air (air = 1)
X. Stability and Reactivity:
Stability: stable
Conditions to avoid: elevated temperatures, contact with acids and oxidizers, freezing.
Incompatibility: oxidizers, strong acids, alum, ammonium salts, chlorinated rubber.
Hazardous decomposition products: When heated to decomposition these products may emit smoke,
irritating fumes, CO, CO2, acrylic monomers, various hydrocarbons, and toxic gases and fumes. Contact with acids
may produce trace amounts of formaldehyde.
4
Hazardous polymerization: will not occur.
XI. Toxicological Information:
Acrylic Polymer
Contact:
Can cause slight eye and skin irritation
Skin irritation-Rabbit: Practically non-irritating
Eye irritation-Rabbit: Inconsequential irritation
Dermal LD50-Rabbit: >5,000 mg/kg
Ingestion:
Oral LD50-Rat: >5,000 mg/kg
Inhalation:
Inhalation of vapor or mist can cause headache, nausea, and irritation of the nose, throat, and lungs.
Calcium carbonate
An eye and skin irritant, and a nuisance dust. Long term exposure to nuisance dust may cause respiratory problems.
Such dust exposures are not expected with use of this product.
Ingestion:
Oral-Rat LD50=6,450 mg/kg.
Cellulose
Ingestion:
Oral-Rat LD50: >2,000 mg/kg.
Ester alcohol[2,2,4-trimethyl-1,3-pentanediolmonoisobutyrate]
Contact:
Dermal LD50- Guinea pig: >20 ml/kg (highest concentration tested).
Dermal LD50- Rabbit: >16 ml/kg (highest concentration tested).
Ingestion:
Oral LDLo-Rat: 3,200 mg/kg.
Oral LDLo-Mouse 3,200 mg/kg.
Oral LD50- Mouse: 1.6-3.2 g/kg .
Oral LD50- Rat: 6.86 ml/kg.
Subchronic Toxicity Data:
Oral study (2 weeks, rat): NOAEL = 1000 mg/kg/day (increase in weight: liver);
NOEL = 100 mg/kg/day.
Definitions: NOAEL-no observed adverse effect level.
NOEL-no observed effect level.
Ingestion may cause abdominal discomfort, nausea, and vomiting. Skin contact may cause slight irritation
with discomfort and redness, and eye contact may cause mild discomfort and excess redness of the
conjunctiva.
Inhalation:
Inhalation LC50- Rat: 2.75mg/l/6 hours (highest concentration tested).
Propylene glycol
Contact:
An eye irritant. Eye effects-Rabbit, adult 100 mg: mild irritation effects.
Eye effects-Rabbit, adult 500 mg/24H: mild irritation effects.
Skin-Human 104 mg/3D-I: moderate irritation effects.
Dermal LD50-Rabbit: >10,000 mg/kg.
Ingestion:
Oral LD50-Mouse: 22g/kg.
Oral LD50-Rabbit: >20,000 mg/kg.
Oral LD50-Rat: 20g/kg.
5
Human systemic effects by ingestion: general anesthesia, convulsions, and changes in surface
electroencephalogram.
Oral-Child TDLo: 79g/kg/56W-I: central nervous system effects.
Parenteral-Infant TDLo: 10g/kg/3D-C: systemic effects.
Other:
DNA Inhibition-Mouse-subcutaneous 8,000 mg/kg.
Cytogenic Analysis-Mouse-subcutaneous 8,000 mg/kg.
Cytogenic Analysis-Hamster: fibroblast 32 g/L.
Experimental teratogenic and reproductive effects have been noted in studies with laboratory animals
injected with this substance.
Overexposure has been suggested as a cause of kidney damage in laboratory animals, and may aggravate
certain pre-existing disorders of the kidneys in humans.
Silica, amorphous
Present as a minor impurity in titanium dioxide.
Contact:
Eye effects-Rabbit, adult 8300 ug/48H.
An eye irritant and nuisance dust.
Ingestion:
Poison by intravenous route.
Intravenous-Mouse LDLo: 234 mg/kg.
Inhalation:
An inhalation hazard.
Other:
DNA Damage-Unspecified effects: lyms 500 mmol/L.
Questionable carcinogen. Mutation data reported. Primary irritant.
Silica, crystalline-quartz
Present as a minor impurity in calcium carbonate and diatomaceous earth ingredients.
Confirmed carcinogen with experimental carcinogenic, tumorigenic, and neoplastigenic
data.
Inhalation:
Inhalation-Human TCLo: 16 mppcf/8H/17.9Y-I: Pulmonary system effects.
Inhalation-Human LCLo: 300 ug/m³/10Y-I: System effects.
Inhalation-Rat TCLo: 50 mg/m³6H/71W-I: Carcinogenic effects.
Chronic exposure to dust may cause silicosis.
Human effects by inhalation: cough, wheezing, dyspnea (difficult or labored breathing),
impaired pulmonary function, and liver effects.
Other:
Intratracheal- Rat TDLo: 111 mg/kg: Carcinogenic effects.
Intratracheal- Rat LDLo: 200 mg/kg.
Titanium Dioxide
A nuisance dust and a human skin irritant. Mild irritation effects reported on human skin (300 ug/3D-I:
Mild irritation effects).
Ingestion:
Ingestion-Rat Oral ALD50: >24,000 mg/kg.
In lifetime animal feeding tests at levels up to 50,000 ppm, titanium dioxide showed no evidence of cancer
or other significant adverse effects in either rats or mice. No animal data are available to define the
developmental or reproductive toxicity of titanium dioxide. Tests have shown that titanium dioxide does
not cause genetic damage in bacterial or mammalian cell cultures, or in animals. Animal testing indicates
amorphous silica does not have carcinogenic or reproductive effects. Amorphous silica has not produced
genetic damage in bacterial cultures.
Inhalation:
Inhalation-Rat 4HR ALC: 4HR ALC: >6.82 mg/L.
6
In short term inhalation studies of titanium dioxide mixtures containing aluminum hydroxide surface
treatments and silicon dioxide impurities, a slight fibrogenic response occurred in animals exposed to
respirable dust concentrations of 1,300 mg/m³ over a four week period. A typical dust cell reaction but no
fibrogenic response was noted in animals similarly exposed to titanium dioxide, or titanium dioxide
mixtures containing from 1% to 3% aluminum hydroxide and 2.7 to 6% silicon dioxide. Aluminum
hydroxide is a surface treatment used to refine rutile grade titanium dioxide pigments. Silicon dioxide is a
naturally occurring impurity in titanium dioxide pigments.
In lifetime inhalation studies (1985) in rats of respirable titanium dioxide at levels up to 250 mg/m³, no
compound-related clinical signs of toxicity were observed in the exposed animals. Slight pulmonary
fibrosis was observed at 50 and 250 mg/m³ respirable dust levels, but not at 10 mg/m³ (equal to the ACGIH
TLV). There was no evidence of cancer in animals exposed to 10 or 50 mg/m³ respirable titanium dioxide.
Microscopic lung tumors were observed in 17 percent of the rats exposed to 250 mg/m³ respirable titanium
dioxide particles. The lung tumors seen in the rats were different from common human lung cancers,
relative to anatomical location, occurred only at dust levels which overwhelmed the animals lung
clearance mechanisms, and therefore, are of questionable biological relevance for humans.
Zinc Oxide
Contact:
A skin and eye irritant. Skin inflammation (dermatitis).
Skin-Rabbit, adult 500 mg/24H-Mild irritation effects.
Eye effects-Rabbit, adult 500 mg/24H-Mild irritation effects.
Inhalation:
Inhalation-Human TCLo: 600 mg/m³: Pulmonary system effects
Respiratory tract irritation. Lung disease is aggravated by exposure.
Inhalation-Mouse LC50: 2500 mg/m³.
Cytogenic Analysis-Rat-Inhalation 100 ug/m³.
Ingestion:
Oral-Human LDLo: 500 mg/kg
Oral-Rat LDLo: 6846 mg/kg (1-22D preg): Reproductive effects.
Oral-Rat LDLo: 6846 mg/kg (1-22D preg): Teratogenic effects.
Oral-Mouse LD50: 7950 mg/m³.
Other:
DNA Damage-Escherichia coli 3000 ppm
Zinc pyrithione
Contact:
Dermal-Rabbit LD50: >2g/kg.
Eye Irritation: Draize score for a rabbit = 80.5/110. This material is expected to cause
irreversible effects to the cornea with impairment of vision or corrosion to the eyes.
Skin Irritation: Primary Irritation Index for a rabbit = 0.38/8.0. Not expected to be
irritating to skin.
Skin Sensitization: Negative skin sensitizer, guinea pig � Buehler Method.
Rodents have been observed to experience muscle weakness from prolonged oral and
skin exposures, although such findings were not duplicated with monkeys.
Ingestion:
Oral-Monkey LD50: >1,000/kg.
Oral-Rat LD50 = 269 mg/kg.
Reproductive and/or developmental toxicity was observed in laboratory animals only at
high doses that were maternally toxic. The production of vomiting would provide
protection against systemic toxicity. Chronic toxicity from ingestion is highly unlikely.
Inhalation:
Inhalation-Rat LC50 (4h) nose only = 0.61 mg/l (aerosol dust).
Inhalation-Rat LC50 (1h) nose only = 2.4 mg/l (aerosol dust).
Zinc pyrithione, the active ingredient of the biocide used in these exterior coatings, is
bound within the acrylic vehicle. Exposure from any of these routes is not expected.
7
XII. Ecological Information:
No data is available for these finished products. Do not discharge to storm sewers or waterways. No
bioconcentrations of the latex emulsion is expected because of its high molecular weight. Biodegradation will be
low. A spill into surface waters may shift the pH and be toxic to aquatic organisms.
1-Methyl-3,5,7-triaza-1-azoniatricyclodecane chloride (in can preservative <0.1%)
LC50: 136 mg/l 48 hours (Daphnia magna)
LC50: 337 mg/l 96 hours (Bluegill sunfish)
LC50: 624 mg/l 96 hours (Rainbow trout)
Ethylhydroxyethyl cellulose
96 H LC 50 fish (n.o.s.) > 100 mg/l
Degradation: Not readily biodegradable. <60%BOD, 28 days, Closed Bottle Test (OECD 301D)
Ester alcohol [2,2,4-trimethyl-1,3-pentanediolmonoisobutyrate]
Acute Aquatic Effects:
96 H LC50 Flathead minnow; 32mg/l NOEC 10 ml/l
96 H LC50 Sideswimmer: 100 mg/l NOEC 10 ml/l
48 H EC 50 Daphnid: >100 mg/l
96 H LC50 Pill bug: >100 ml/l
96 H LC50 Flatworm: 40 mg/l NOEC 10 mg/l
96 H LC50 Segmented worm: 32 ml/l NOEC 10 mg/l
96 H LC50 snail: >100 mg/l
Titanium Dioxide: LC50 fathead minnows: >1,000 mg/L.
Zinc pyrithione
Acute Aquatic Effects:
96 H LC50 Rainbow trout: 0.0032 mg/l.
96 H LC50 Fathead minnow: 0.0026 mg/l.
96 H LC50 Sheepshead minnow: 0.4 mg/l.
Environmental acute toxicity:
LD50 Northern Bobwhite Quail = 60 mg/kg.
LC50 Northern Bobwhite Quail = 1110 ppm
Chemical Fate Information: Is not available for these products.
XIII. Disposal Considerations:
Waste Disposal: Do not dump into any sewers, on the ground, or into any body of water. Dispose of in accordance
with federal, state, and local regulations. The paint, as supplied, does not meet the definition of a hazardous waste
under 40 CFR part 261. Use or contamination can change the materials characteristics and the owner is responsible
for proper waste disposal. Do not discharge material to natural waters or place liquids in landfills.
XIV. Transport Information:
DOT Proper Shipping Description: None
DOT Hazard Class/Division Label: None
Shipping Containers: 1 - Gallon cans & 5 - Gallon buckets
XV. Regulatory Information:
OSHA Hazard Communication Standard 29 CFR 1910.1200: calcium carbonate, titanium dioxide, diatomaceous
earth, zinc oxide, zinc pyrithione, cellulose, silica, and propylene glycol are considered hazardous ingredients.
8
SARA Hazard Category: This product has been reviewed according to the EPA Hazard categories promulgated
under sections 311 and 312 of SARA Title III and is considered, under applicable definitions, to meet the following
categories:
An immediate health hazard
A delayed health hazard
Section 302 Extremely Hazardous Substances: none present above 1% of reporting threshold.
SARA 313 Information:
This product contains the following substances subject to the reporting requirements of section 313 of SARA Title
III:
Chemical Name CAS Number Present in CERCLA RQ, Pounds
Zinc oxide 1314-13-2 0-3% in all products No RQ
(as a zinc compound)
Zinc pyrithione 13464-41-7 <0.4% in all products No RQ
(as a zinc compound)
CERCLA: This product contains no reportable quantities. Immediate reporting to the National Response
Center (1-800-424-8802), state, and local authorities is required if more than the reportable quantity is released
to the environment.
XVI. Other Information: This product is for industrial use only and is not for resale.
9
|