Distributed By: MSDS 031
Invensys Foxboro Foxboro Rev Date: April 2006
Foxboro, MA 02035 U.S.A. Part Number B0134LM
1-866-746-6477 Page 1 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 1 of 8
DOW CORNING 200(R) FLUID, 2 CST.
1. IDENTIFICATION OF THE SUBSTANCE AND OF THE COMPANY
24 Hour Emergency Telephone: (989) 496-5900
Dow Corning Corporation
South Saginaw Road Customer Service: (989) 496-6000
Midland, Michigan 48686 Product Disposal Information: (989) 496-6315
CHEMTREC: (800) 424-9300
MSDS No.: 01013114 Revision Date: 2003/04/03
Generic Description: Silicone
Physical Form: Liquid
Color: Colorless
Odor: Odorless
NFPA Profile: Health 0 Flammability 2 Instability/Reactivity 0
Note: NFPA = National Fire Protection Association
2. OSHA HAZARDOUS COMPONENTS
CAS Number Wt % Component Name
141-63-9 > 60.0 Dodecamethylpentasiloxane
540-97-6 1.0 - 5.0 Dodecamethyl cyclohexasiloxane
541-02-6 1.0 - 5.0 Decamethylcyclopentasiloxane
The above components are hazardous as defined in 29 CFR 1910.1200.
3. EFFECTS OF OVEREXPOSURE
Acute Effects
Eye: Direct contact may cause temporary redness and discomfort.
Skin: No significant irritation expected from a single short-term exposure.
Inhalation: No significant effects expected from a single short-term exposure.
Oral: Low ingestion hazard in normal use.
Prolonged/Repeated Exposure Effects
Skin: No known applicable information.
Inhalation: No known applicable information.
Oral: No known applicable information.
Signs and Symptoms of Overexposure
No known applicable information.
MSDS 031
Part Number B0134LM
Page 2 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 2 of 8
DOW CORNING 200(R) FLUID, 2 CST.
Medical Conditions Aggravated by Exposure
No known applicable information.
The above listed potential effects of overexposure are based on actual data, results of studies performed upon similar
compositions, component data and/or expert review of the product. Please refer to Section 11 for the detailed toxicology
information.
4. FIRST AID MEASURES
Eye: Immediately flush with water.
Skin: No first aid should be needed.
Inhalation: No first aid should be needed.
Oral: No first aid should be needed.
Comments: Treat symptomatically.
5. FIRE FIGHTING MEASURES
Flash Point: 188.6 掳F / 87 掳C (Tag Closed Cup)
Autoignition Not determined.
Temperature:
Flammability Limits in Air: Not determined.
Extinguishing Media: On large fires use dry chemical, foam or water spray. On small fires use carbon dioxide
(CO2), dry chemical or water spray. Water can be used to cool fire exposed containers.
Fire Fighting Measures: Self-contained breathing apparatus and protective clothing should be worn in fighting
large fires involving chemicals. Determine the need to evacuate or isolate the area
according to your local emergency plan. Use water spray to keep fire exposed containers
cool.
Unusual Fire Hazards: None.
Hazardous Decomposition Products
Thermal breakdown of this product during fire or very high heat conditions may evolve the following hazardous
decomposition products: Carbon oxides and traces of incompletely burned carbon compounds. Silicon dioxide.
Formaldehyde.
6. ACCIDENTAL RELEASE MEASURES
MSDS 031
Part Number B0134LM
Page 3 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 3 of 8
DOW CORNING 200(R) FLUID, 2 CST.
Containment/Clean up: Determine whether to evacuate or isolate the area according to your local emergency
plan. Observe all personal protection equipment recommendations described in Sections
5 and 8. For large spills, provide diking or other appropriate containment to keep material
from spreading. If diked material can be pumped, store recovered material in appropriate
container. Clean up remaining materials from spill with suitable absorbant. Clean area
as appropriate since some silicone materials, even in small quantities, may present a slip
hazard. Final cleaning may require use of steam, solvents or detergents. Dispose of
saturated absorbant or cleaning materials appropriately, since spontaneous heating may
occur. Local, state and federal laws and regulations may apply to releases and disposal
of this material, as well as those materials and items employed in the cleanup of releases.
You will need to determine which federal, state and local laws and regulations are
applicable. Sections 13 and 15 of this MSDS provide information regarding certain
federal and state requirements.
Note: See section 8 for Personal Protective Equipment for Spills. Call Dow Corning Corporation, (989) 496-5900, if
additional information is required.
7. HANDLING AND STORAGE
Use with adequate ventilation. Avoid eye contact.
Static electricity will accumulate and may ignite vapors. Prevent a possible fire hazard by bonding and grounding or
inert gas purge. Keep container closed and away from heat, sparks, and flame.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Component Exposure Limits
CAS Number Component Name Exposure Limits
541-02-6 Decamethylcyclopentasiloxane See Section 11 comments.
Engineering Controls
Local Ventilation: Recommended.
General Ventilation: Recommended.
Personal Protective Equipment for Routine Handling
Eyes: Use proper protection - safety glasses as a minimum.
Skin: Washing at mealtime and end of shift is adequate.
Suitable Gloves: No special protection needed.
Inhalation: No respiratory protection should be needed.
Suitable Respirator: None should be needed.
Personal Protective Equipment for Spills
Eyes: Use proper protection - safety glasses as a minimum.
MSDS 031
Part Number B0134LM
Page 4 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 4 of 8
DOW CORNING 200(R) FLUID, 2 CST.
Skin: Washing at mealtime and end of shift is adequate.
Inhalation/Suitable No respiratory protection should be needed.
Respirator:
Precautionary Measures: Avoid eye contact. Use reasonable care.
Comments: When heated to temperatures above 150 degrees C in the presence of air, product can
form formaldehyde vapors. Formaldehyde is a potential cancer hazard, a known skin and
respiratory sensitizer, and an irritant to the eyes, nose, throat, skin, and digestive system.
Safe handling conditions may be maintained by keeping vapor concentrations within the
OSHA Permissible Exposure Limit for formaldehyde.
Note: These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may
require added precautions.
9. PHYSICAL AND CHEMICAL PROPERTIES
Physical Form: Liquid
Color: Colorless
Odor: Odorless
Specific Gravity @ 25掳C: 0.872
Viscosity: 2 cSt
Freezing/Melting Point: Not determined.
Boiling Point: 230 掳C
Vapor Pressure @ 25掳C: Not determined.
Vapor Density: Not determined.
Solubility in Water: Not determined.
pH: Not determined.
Volatile Content: Not determined.
Note: The above information is not intended for use in preparing product specifications. Contact Dow Corning before writing
specifications.
10. STABILITY AND REACTIVITY
Chemical Stability: Stable.
Hazardous Hazardous polymerization will not occur.
Polymerization:
Conditions to Avoid: None.
Materials to Avoid: Oxidizing material can cause a reaction.
11. TOXICOLOGICAL INFORMATION
Component Toxicology Information
Repeated inhalation or oral exposure of mice and rats to decamethylcyclopentasiloxane produced an increase in
liver size. No gross histopathological or significant clinical chemistry effects were observed. An increase in liver
MSDS 031
Part Number B0134LM
Page 5 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 5 of 8
DOW CORNING 200(R) FLUID, 2 CST.
metabolizing enzymes, as well as a transient increase in the number of normal cells (hyperplasia) followed by an
increase in cell size (hypertrophy) were determined to be the underlying causes of the liver enlargement. The
biochemical mechanisms producing these effects are highly sensitive in rodents, while similar mechanisms in
humans are insensitive. Good industrial hygiene practice minimizes inhalation exposure to any chemical. Dow
Corning has set an exposure guideline of 10 ppm TWA for this material.
Special Hazard Information on Components
No known applicable information.
12. ECOLOGICAL INFORMATION
Environmental Fate and Distribution
Air: This product is a high molecular weight liquid polymer which has a very low vapour
pressure (<1 mm Hg). As a result it is unlikely to become an atmospheric contaminant
unless generated as an aerosol.
Water: This product has a very low water solubility (< 100 ppb). As it has a specific gravity of < 1,
if discharged to water, it will initially form a surface film. As the product is non volatile and
has a high binding affinity for particulate matter, it will adsorb to particulates and sediment
out.
Soil: If discharged to surface water, this product will bind to sediment. If discharged in effluent
to a waste water treatment plant, the product is removed from the aqueous phase by
binding to sewage sludge. If the sewage sludge is subsequently spread on soil, the
silicone product is expected to degrade.
Degradation: This product, polydimethylsiloxane, degrades in soil abiotically to form smaller molecules.
These in turn are either biodegraded in soil or volatilized into the air where they are
broken down in the presence of sunlight. Under appropriate conditions, the ultimate
degradation products are inorganic silica, carbon dioxide and water vapour. Due to the
very low water solubility of this product, standard OECD protocols for ready and inherent
biodegradability are not suitable for measuring the biodegradability of this product. The
product is removed >80% during the sewage treatment process.
Environmental Effects
Toxicity to Water Based on analogy to similar materials this product is expected to exhibit low toxicity to
Organisms: aquatic organisms.
Toxicity to Soil Organisms: Experiments show that when sewage sludge containing polydimethylsiloxane is added to
soil, it has no effect on soil micro-organisms, earthworms or subsequent crops grown in
the soil.
Bioaccumulation: This product is a liquid and is a high molecular weight polymer. Due to its physical size it
is unable to pass through, or be absorbed by biological membranes. This has been
confirmed by testing or analogy with similar products.
Fate and Effects in Waste Water Treatment Plants
MSDS 031
Part Number B0134LM
Page 6 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 6 of 8
DOW CORNING 200(R) FLUID, 2 CST.
This product or similar products has been shown to be non-toxic to sewage sludge bacteria.
Ecotoxicity Classification Criteria
Hazard Parameters (LC50 or EC50) High Medium Low
Acute Aquatic Toxicity (mg/L) <=1 >1 and <=100 >100
Acute Terrestrial Toxicity <=100 >100 and <= 2000 >2000
This table is adapted from "Environmental Toxicology and Risk Assessment", ASTM STP 1179, p.34, 1993.
This table can be used to classify the ecotoxicity of this product when ecotoxicity data is listed above. Please read the other information presented
in the section concerning the overall ecological safety of this material.
13. DISPOSAL CONSIDERATIONS
RCRA Hazard Class (40 CFR 261)
When a decision is made to discard this material, as received, is it classified as a hazardous waste? No
State or local laws may impose additional regulatory requirements regarding disposal.
Call Dow Corning Corporate Environmental Management, (989) 496-6315, if additional information is required.
14. TRANSPORT INFORMATION
DOT Road Shipment Information (49 CFR 172.101)
Proper Shipping Name: COMBUSTIBLE LIQUID, N.O.S.
Hazard Technical Name: POLYDIMETHYLSILOXANE
Hazard Class: COMBUSTIBLE LIQUID
UN/NA Number: NA1993
Packing Group: III
Remarks: Above applies only to containers over 119 gallons or 450 liters.
Ocean Shipment (IMDG)
Not subject to IMDG code.
Air Shipment (IATA)
Not subject to IATA regulations.
Call Dow Corning Transportation, (989) 496-8577, if additional information is required.
15. REGULATORY INFORMATION
Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200.
TSCA Status: All chemical substances in this material are included on or exempted from listing on the TSCA
MSDS 031
Part Number B0134LM
Page 7 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 7 of 8
DOW CORNING 200(R) FLUID, 2 CST.
Inventory of Chemical Substances.
EPA SARA Title III Chemical Listings
Section 302 Extremely Hazardous Substances:
None.
Section 304 CERCLA Hazardous Substances:
None.
Section 312 Hazard Class:
Acute: No
Chronic: No
Fire: Yes
Pressure: No
Reactive: No
Section 313 Toxic Chemicals:
None present or none present in regulated quantities.
Supplemental State Compliance Information
California
Warning: This product contains the following chemical(s) listed by the State of California under the Safe Drinking
Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other
reproductive harm.
None known.
Massachusetts
No ingredient regulated by MA Right-to-Know Law present.
New Jersey
CAS Number Wt % Component Name
141-63-9 > 60.0 Dodecamethylpentasiloxane
63148-62-9 15.0 - 40.0 Polydimethylsiloxane
540-97-6 1.0 - 5.0 Dodecamethyl cyclohexasiloxane
541-02-6 1.0 - 5.0 Decamethylcyclopentasiloxane
Pennsylvania
MSDS 031
Part Number B0134LM
Page 8 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 8 of 8
DOW CORNING 200(R) FLUID, 2 CST.
CAS Number Wt % Component Name
141-63-9 > 60.0 Dodecamethylpentasiloxane
63148-62-9 15.0 - 40.0 Polydimethylsiloxane
16. OTHER INFORMATION
Prepared by: Dow Corning Corporation
These data are offered in good faith as typical values and not as product specifications. No warranty, either
expressed or implied, is hereby made. The recommended industrial hygiene and safe handling procedures are
believed to be generally applicable. However, each user should review these recommendations in the specific
context of the intended use and determine whether they are appropriate.
(R) indicates Registered Trademark
MSDS 031
Part Number B0134LM
Page 9 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 1 of 7
DOW CORNING 200(R) FLUID, 5 CST.
1. IDENTIFICATION OF THE SUBSTANCE AND OF THE COMPANY
24 Hour Emergency Telephone: (989) 496-5900
Dow Corning Corporation
South Saginaw Road Customer Service: (989) 496-6000
Midland, Michigan 48686 Product Disposal Information: (989) 496-6315
CHEMTREC: (800) 424-9300
MSDS No.: 01013131 Revision Date: 2003/01/06
Generic Description: Silicone
Physical Form: Liquid
Color: Colorless
Odor: Odorless
NFPA Profile: Health 0 Flammability 1 Instability/Reactivity 0
Note: NFPA = National Fire Protection Association
2. OSHA HAZARDOUS COMPONENTS
None present. This is not a hazardous material as defined in the OSHA Hazard Communication Standard.
3. EFFECTS OF OVEREXPOSURE
Acute Effects
Eye: Direct contact may cause temporary redness and discomfort.
Skin: No significant irritation expected from a single short-term exposure.
Inhalation: No significant effects expected from a single short-term exposure.
Oral: Low ingestion hazard in normal use.
Prolonged/Repeated Exposure Effects
Skin: No known applicable information.
Inhalation: No known applicable information.
Oral: No known applicable information.
Signs and Symptoms of Overexposure
No known applicable information.
Medical Conditions Aggravated by Exposure
No known applicable information.
The above listed potential effects of overexposure are based on actual data, results of studies performed upon similar
compositions, component data and/or expert review of the product. Please refer to Section 11 for the detailed toxicology
information.
MSDS 031
Part Number B0134LM
Page 10 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 2 of 7
DOW CORNING 200(R) FLUID, 5 CST.
4. FIRST AID MEASURES
Eye: Immediately flush with water.
Skin: No first aid should be needed.
Inhalation: No first aid should be needed.
Oral: No first aid should be needed.
Comments: Treat symptomatically.
5. FIRE FIGHTING MEASURES
Flash Point: > 214 掳F / > 101.1 掳C (Closed Cup)
Autoignition Not determined.
Temperature:
Flammability Limits in Air: Not determined.
Extinguishing Media: On large fires use dry chemical, foam or water spray. On small fires use carbon dioxide
(CO2), dry chemical or water spray. Water can be used to cool fire exposed containers.
Fire Fighting Measures: Self-contained breathing apparatus and protective clothing should be worn in fighting
large fires involving chemicals. Determine the need to evacuate or isolate the area
according to your local emergency plan. Use water spray to keep fire exposed containers
cool.
Unusual Fire Hazards: None.
Hazardous Decomposition Products
Thermal breakdown of this product during fire or very high heat conditions may evolve the following hazardous
decomposition products: Carbon oxides and traces of incompletely burned carbon compounds. Silicon dioxide.
Formaldehyde.
6. ACCIDENTAL RELEASE MEASURES
MSDS 031
Part Number B0134LM
Page 11 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 3 of 7
DOW CORNING 200(R) FLUID, 5 CST.
Containment/Clean up: Determine whether to evacuate or isolate the area according to your local emergency
plan. Observe all personal protection equipment recommendations described in Sections
5 and 8. For large spills, provide diking or other appropriate containment to keep material
from spreading. If diked material can be pumped, store recovered material in appropriate
container. Clean up remaining materials from spill with suitable absorbant. Clean area
as appropriate since some silicone materials, even in small quantities, may present a slip
hazard. Final cleaning may require use of steam, solvents or detergents. Dispose of
saturated absorbant or cleaning materials appropriately, since spontaneous heating may
occur. Local, state and federal laws and regulations may apply to releases and disposal
of this material, as well as those materials and items employed in the cleanup of releases.
You will need to determine which federal, state and local laws and regulations are
applicable. Sections 13 and 15 of this MSDS provide information regarding certain
federal and state requirements.
Note: See section 8 for Personal Protective Equipment for Spills. Call Dow Corning Corporation, (989) 496-5900, if
additional information is required.
7. HANDLING AND STORAGE
Use with adequate ventilation. Avoid eye contact.
Use reasonable care and store away from oxidizing materials.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Component Exposure Limits
There are no components with workplace exposure limits.
Engineering Controls
Local Ventilation: None should be needed.
General Ventilation: Recommended.
Personal Protective Equipment for Routine Handling
Eyes: Use proper protection - safety glasses as a minimum.
Skin: Washing at mealtime and end of shift is adequate.
Suitable Gloves: No special protection needed.
Inhalation: No respiratory protection should be needed.
Suitable Respirator: None should be needed.
Personal Protective Equipment for Spills
Eyes: Use proper protection - safety glasses as a minimum.
Skin: Washing at mealtime and end of shift is adequate.
MSDS 031
Part Number B0134LM
Page 12 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 4 of 7
DOW CORNING 200(R) FLUID, 5 CST.
Inhalation/Suitable No respiratory protection should be needed.
Respirator:
Precautionary Measures: Avoid eye contact. Use reasonable care.
Comments: When heated to temperatures above 150 degrees C in the presence of air, product can
form formaldehyde vapors. Formaldehyde is a potential cancer hazard, a known skin and
respiratory sensitizer, and an irritant to the eyes, nose, throat, skin, and digestive system.
Safe handling conditions may be maintained by keeping vapor concentrations within the
OSHA Permissible Exposure Limit for formaldehyde.
Note: These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may
require added precautions. For further information regarding aerosol inhalation toxicity, please refer to the guidance document
regarding the use of silicone-based materials in aerosol applications that has been developed by the silicone industry
(www.SEHSC.com) or contact the Dow Corning customer service group.
9. PHYSICAL AND CHEMICAL PROPERTIES
Physical Form: Liquid
Color: Colorless
Odor: Odorless
Specific Gravity @ 25掳C: 0.915
Viscosity: 5 cSt
Freezing/Melting Point: Not determined.
Boiling Point: > 35 掳C
Vapor Pressure @ 25掳C: Not determined.
Vapor Density: Not determined.
Solubility in Water: Not determined.
pH: Not determined.
Volatile Content: Not determined.
Note: The above information is not intended for use in preparing product specifications. Contact Dow Corning before writing
specifications.
10. STABILITY AND REACTIVITY
Chemical Stability: Stable.
Hazardous Hazardous polymerization will not occur.
Polymerization:
Conditions to Avoid: None.
Materials to Avoid: Oxidizing material can cause a reaction.
11. TOXICOLOGICAL INFORMATION
Special Hazard Information on Components
No known applicable information.
MSDS 031
Part Number B0134LM
Page 13 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 5 of 7
DOW CORNING 200(R) FLUID, 5 CST.
12. ECOLOGICAL INFORMATION
Environmental Fate and Distribution
Air: This product is a high molecular weight liquid polymer which has a very low vapour
pressure (<1 mm Hg). As a result it is unlikely to become an atmospheric contaminant
unless generated as an aerosol.
Water: This product has a very low water solubility (< 100 ppb). As it has a specific gravity of < 1,
if discharged to water, it will initially form a surface film. As the product is non volatile and
has a high binding affinity for particulate matter, it will adsorb to particulates and sediment
out.
Soil: If discharged to surface water, this product will bind to sediment. If discharged in effluent
to a waste water treatment plant, the product is removed from the aqueous phase by
binding to sewage sludge. If the sewage sludge is subsequently spread on soil, the
silicone product is expected to degrade.
Degradation: This product, polydimethylsiloxane, degrades in soil abiotically to form smaller molecules.
These in turn are either biodegraded in soil or volatilized into the air where they are
broken down in the presence of sunlight. Under appropriate conditions, the ultimate
degradation products are inorganic silica, carbon dioxide and water vapour. Due to the
very low water solubility of this product, standard OECD protocols for ready and inherent
biodegradability are not suitable for measuring the biodegradability of this product. The
product is removed >80% during the sewage treatment process.
Environmental Effects
Toxicity to Water Based on analogy to similar materials this product is expected to exhibit low toxicity to
Organisms: aquatic organisms.
Toxicity to Soil Organisms: Experiments show that when sewage sludge containing polydimethylsiloxane is added to
soil, it has no effect on soil micro-organisms, earthworms or subsequent crops grown in
the soil.
Bioaccumulation: This product is a liquid and is a high molecular weight polymer. Due to its physical size it
is unable to pass through, or be absorbed by biological membranes. This has been
confirmed by testing or analogy with similar products.
Fate and Effects in Waste Water Treatment Plants
This product or similar products has been shown to be non-toxic to sewage sludge bacteria.
Ecotoxicity Classification Criteria
Hazard Parameters (LC50 or EC50) High Medium Low
Acute Aquatic Toxicity (mg/L) <=1 >1 and <=100 >100
Acute Terrestrial Toxicity <=100 >100 and <= 2000 >2000
This table is adapted from "Environmental Toxicology and Risk Assessment", ASTM STP 1179, p.34, 1993.
This table can be used to classify the ecotoxicity of this product when ecotoxicity data is listed above. Please read the other information presented
in the section concerning the overall ecological safety of this material.
13. DISPOSAL CONSIDERATIONS
MSDS 031
Part Number B0134LM
Page 14 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 6 of 7
DOW CORNING 200(R) FLUID, 5 CST.
RCRA Hazard Class (40 CFR 261)
When a decision is made to discard this material, as received, is it classified as a hazardous waste? No
State or local laws may impose additional regulatory requirements regarding disposal.
Call Dow Corning Corporate Environmental Management, (989) 496-6315, if additional information is required.
14. TRANSPORT INFORMATION
DOT Road Shipment Information (49 CFR 172.101)
Not subject to DOT.
Ocean Shipment (IMDG)
Not subject to IMDG code.
Air Shipment (IATA)
Not subject to IATA regulations.
Call Dow Corning Transportation, (989) 496-8577, if additional information is required.
15. REGULATORY INFORMATION
Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200.
TSCA Status: All chemical substances in this material are included on or exempted from listing on the TSCA
Inventory of Chemical Substances.
EPA SARA Title III Chemical Listings
Section 302 Extremely Hazardous Substances:
None.
Section 304 CERCLA Hazardous Substances:
None.
Section 312 Hazard Class:
Acute: No
Chronic: No
Fire: No
Pressure: No
Reactive: No
Section 313 Toxic Chemicals:
None present or none present in regulated quantities.
MSDS 031
Part Number B0134LM
Page 15 of 15
DOW CORNING CORPORATION
Material Safety Data Sheet
Page: 7 of 7
DOW CORNING 200(R) FLUID, 5 CST.
Supplemental State Compliance Information
California
Warning: This product contains the following chemical(s) listed by the State of California under the Safe Drinking
Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other
reproductive harm.
None known.
Massachusetts
No ingredient regulated by MA Right-to-Know Law present.
New Jersey
CAS Number Wt % Component Name
63148-62-9 > 60.0 Polydimethylsiloxane
Pennsylvania
CAS Number Wt % Component Name
63148-62-9 > 60.0 Polydimethylsiloxane
16. OTHER INFORMATION
Prepared by: Dow Corning Corporation
These data are offered in good faith as typical values and not as product specifications. No warranty, either
expressed or implied, is hereby made. The recommended industrial hygiene and safe handling procedures are
believed to be generally applicable. However, each user should review these recommendations in the specific
context of the intended use and determine whether they are appropriate.
(R) indicates Registered Trademark
|