Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: marplex_com_au---Reny_1002F.asp
                          MARPLEX691 614 A.C.N. 004 691LTD
AUSTRALIA PTY 614
A.B.N. 78 004
Established 1967 Material Safety Data Sheet (MSDS): Code Reny




RENY庐 MODIFIED MXD6 POLYAMIDE ENGINEERING THERMOPLASTIC
RENY庐 IS A REGISTRED TRADEMARK OF MITSUBISHI ENGINEERING PLASTICS CORPORATION (JAPAN)

RENY庐 1002F
RENY庐 1002F is the 30% glass fibre filled Polyamide MXD6 grade in the Reny庐 range. Compared to standard Nylon
6 and 66 reinforced grades, Reny庐 1002F offers exceptional high strength and rigidity, low water absorption and a
high glass transition temperature. Reny庐 1002F is especially suitable as a metal replacement for structural
components with typical uses being automotive door handles, timing belt pulleys and domestic window winder
casing mechanisms.

DRY WET TESTING
VALUES VALUES METHODS
CONDITIONS UNITS

1. Mechanical Properties
Izod Impact Strength 12.7 x 6.4 mm - notched J/m 82 76 ASTM D256
12.7 x 6.4 mm - unnotched J/m 600 300 ASTM D256
Tensile Strength 12.7 x 3.2 mm @ 5.0 mm/min MPa 202 158 ASTM D638
Tensile Modulus 12.7 x 3.2 mm @ 5.0 mm/min MPa 11,900 10,600 ASTM D638
Elongation to Fail 12.7 x 3.2 mm @ 5.0 mm/min % 2.0 2.4 ASTM D638
Flexural Strength 12.7 x 6.4 mm @ 2.8 mm/min MPa 256 230 ASTM D790
Flexural Modulus 12.7 x 6.4 mm @ 2.8 mm/min MPa 11,600 9,800 ASTM D790
Compressive Strength 6.4 mm MPa 240 - ASTM D695
Shear Strength 2.0 mm MPa 107 78.5 ASTM D732
Tensile Impact Strength 1.6 mm kJ/m虏 140 111 ASTM D1822

2. Thermal Properties
Heat Deflection Temperature 12.7 x 6.4 mm @ 1.82 MPa 潞C 232 - ASTM D648
Coefficient of Linear Thermal Expansion cm/cm/掳C 1.5 exp-5 - ASTM D696

4. Physical Properties
Specific Gravity - 1.45 - ASTM D792
Rockwell Hardness M 112 - ASTM D785
UL Flammability 1.6 mm Rating HB - UL 94
Water Absorbtion 24 hours % 0.20 - ASTM D570
Moisture Regain 65% RH % 2.0 - ASTM D570
Reinforcement Level % 30 - n/a
Taber Abrasion 1000 cycles mg 23 - ASTM D1044
Mould Shrinkage % 0.5卤0.2 - ASTM D955

DRY indicates "Dry-As-Moulded" and WET indicates "Conditioned at 23 潞C/65% RH" Issued: July 1998
All test resuts were obtained using natural material.


Marplex Australia Pty. Ltd. makes no representation with regard to the completeness or accuracy of the information and any recommendations contained in this
data sheet, and accepts no responsibility for loss or damage whatsoever resulting from the use of, or reliance upon, the information and any recommendation
herein. Marplex Australia Pty. Ltd. products are sold on standard terms and conditions, a copy of which is available on request.
MARPLEX AUSTRALIA PTY. LTD. 221 BROWNS ROAD, NOBLE PARK, VICTORIA 3174
CUSTOMER SERVICE: PHONE (03) 8710 1415, 1800 627 987, FAX (03) 9795 6300
TECHNOLOGY DEPARTMENT: PHONE (03) 8710 1432, FAX (03) 9795 1800
SALES OFFICES: MELBOURNE (03) 8710 1400 鈥? SYDNEY (02) 9891 0044 鈥? ADELAIDE (08) 8274 3710
BRISBANE (07) 3842 3152 鈥? PERTH (08) 9284 0279 鈥? AUCKLAND, NZ (09) 633 0233
TYPICAL PROCESSING CONDITIONS

RENY庐 1002F
The following typical guidelines are offered as initial processing conditions for RENY庐 1002F
In practice, processing parameters may need to be varied to give commercially acceptable performance in conjunction
with optimum physical properties. For specific technical advice on part design or processing conditions, contact the
Marplex Technical Service Department.




Temperature of pellet bed in dehumidifying drier 75 - 85 潞C

Minimum drying time at desired pellet bed temp 2 hours if unopened bag
>12 if already opened bag

Mould temperature 120 - 140 潞C

Nozzle temperature Do not exceed stock
temperature

Stock temperature 255 - 285 潞C

Cylinder temperatures Rear 240 - 260 潞C

Middle 250 - 270 潞C

Front 260 - 280 潞C

Fill speed Fast

Screw speed 40 - 60 rpm

Screw back pressure 0.1 - 0.5 MPa

Injection pressure 60 - 140 MPa

Clamp pressure 5 - 9 kN/cm虏


Comment(s):
1 Reny庐 MXD6 absorbs moisture readily once the original packaging is opened. Ensure adequate
drying of stored material and regrind to avoid moulding splay, nozzle drooling and embrittlement.
2 Reny庐 MXD6 is not compatible with other polymers.

3 It is strongly suggested that the actual drying, moulding die and material temperatures are manually
confirmed using a hand held temperature measuring device.

1 MPa = 145 psi
Conversions:
= 10.2 kg/cm虏
= 10 bar
潞C = 5(潞F-32)/9
1 kN/cm虏 = 0.65 ton/in虏

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
marplex_com_au---Iupilon_H2000R.asp N/A
marplex_com_au---Iupilon_H2000UR.asp N/A
marplex_com_au---Iupilon_H3000.asp N/A
marplex_com_au---Iupilon_H3000UR.asp N/A
marplex_com_au---Iupilon_H4000.asp N/A
marplex_com_au---Iupilon_MB2106.asp N/A
marplex_com_au---Iupilon_S1000.asp N/A
marplex_com_au---Iupilon_S1000R.asp N/A
marplex_com_au---Iupilon_S1000UR.asp N/A
marplex_com_au---Iupilon_S2000.asp N/A
marplex_com_au---Iupilon_S2000UR.asp N/A
marplex_com_au---Iupilon_S3000R.asp N/A
marplex_com_au---Iupilon_S3000UR.asp N/A
marplex_com_au---Iupilon_S3500UR.asp N/A
marplex_com_au---Iupilon_S3600R.asp N/A
marplex_com_au---Iupital.asp N/A
marplex_com_au---Iupital_F10.asp N/A
marplex_com_au---Iupital_F20-51.asp N/A
marplex_com_au---Iupital_F20-52.asp N/A
marplex_com_au---Iupital_F20-54.asp N/A
marplex_com_au---Iupital_F20.asp N/A
marplex_com_au---Iupital_F25.asp N/A
marplex_com_au---Iupital_F30.asp N/A
marplex_com_au---Iupital_F40.asp N/A
marplex_com_au---Iupital_FB2025.asp N/A
marplex_com_au---Iupital_FG2025.asp N/A
marplex_com_au---Iupital_LO21A.asp N/A
marplex_com_au---Luran_358N_MSDS.asp N/A
marplex_com_au---Luran_S_757G_MSDS.asp N/A
marplex_com_au---Luran_S_757R_MSDS.asp N/A
marplex_com_au---Luran_S_776SE_MSDS.asp N/A
marplex_com_au---Luran_S_776S_MSDS.asp N/A
marplex_com_au---Luran_S_777K_MSDS.asp N/A
marplex_com_au---Luran_S_778T_MSDS.asp N/A
marplex_com_au---Luran_S_796M_MSDS.asp N/A
marplex_com_au---Luran_S_797S_MSDS.asp N/A
marplex_com_au---Luran_S_KR2867CWU_MSDS.asp N/A
marplex_com_au---NG02_Natural.asp 621-60-4 621-60-6 621-60-9
marplex_com_au---NG04_Natural.asp 621-60-4 621-60-6 621-60-9
marplex_com_au---NG06_Black.asp N/A
marplex_com_au---NM11_Natural.asp 621-60-4 621-60-6 621-60-9
marplex_com_au---NM19_Natural.asp 621-60-4 621-60-8 621-60-9
marplex_com_au---Polystyrol_143E_MSDS.asp 621-60-4 621-60-8 0621-60-4 0621-60-9
marplex_com_au---Polystyrol_156F_MSDS.asp N/A
marplex_com_au---Polystyrol_158K_MSDS.asp N/A
marplex_com_au---Polystyrol_165H_MSDS.asp 621-60-4 621-60-8 0621-60-4 0621-60-9
marplex_com_au---Polystyrol_476L_MSDS.asp N/A
marplex_com_au---Polystyrol_495F_MSDS.asp N/A
marplex_com_au---Reny_1002F.asp N/A
marplex_com_au---Reny_1012F.asp N/A

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC