Material Name: JM Building Insulation Binder Material Safety Data
Sheet ID: 1035
Section 1 - Chemical Product and Company Identification
Product Name JM Building Insulation Binder
CAS# None Assigned
Generic Name Binder
Formula Mixture
Chemical Name: Mixture
Hazard Label None assigned.
Manufacturer Information
Johns Manville Insulation Group Telephone: 303-978-2000 8:00AM-5:00PM M-F
Building Insulation Division Internet Address: http://www.jm.com
P.O. Box 5108 Emergency: 800-424-9300 (Chemtrec, In English)
Denver, CO 80127 USA
Trade Names: JM Building Insulation Binder
Section 2 - Composition / Information on Ingredients
CAS # Component Percent
7732-18-5 Water 85-95
Trade Secret Carboxy containing polymer 3-10
Trade Secret Polyol 1-4
Trade Secret Silane <1
Trade Secret Paraffinic Oil <1
Trade Secret Surfactant <1
Trade Secret Mineral Acid <1
Section 3 - Hazards Identification
Emergency Overview
APPEARANCE AND ODOR: Light amber colored liquid with slight acrylic odor.
Potential Health Effects
Inhalation
Prolonged or repeated inhalation of vapor or mist may cause slight irritation of nose, throat, and lungs.
Skin
Prolonged or repeated contact may cause slight skin irritation.
Eyes
May cause slight irritation upon contact.
Target Organs
Upper respiratory passages, skin, and eyes.
Medical Conditions Aggravated by Exposure
Pre-existing chronic respiratory or eye diseases or conditions.
Section 4 - First Aid Measures
First Aid: Inhalation
Remove to fresh air.
First Aid: Skin
Wash exposed skin with soap and water. If irritation develops or persists, seek medical attention.
First Aid: Ingestion
Product is not intended to be ingested or eaten. If this product is ingested, irritation of the gastrointestinal (GI) tract may occur,
and should be treated symptomatically. Rinse mouth with water to remove material or dust, and drink plenty of water to help
reduce the irritation. No chronic effects are expected following ingestion.
____________________________________________________________
Page 1 of 4 Issue Date: 08/07/2006 Revision: 1.0000
Material Name: JM Building Insulation Binder Material Safety Data
Sheet ID: 1035
First Aid: Eyes
Flush eyes with water. If irritation persists, contact a physician.
First Aid: Notes to Physician
This product is not expected to produce any chronic health effects from acute exposures. Treatment should be directed toward
removing the source of irritation with symptomatic treatment as necessary.
Section 5 - Fire Fighting Measures
Flash Point: Non-combustible Method Used: Not applicable
Upper Flammable Limit (UFL): Not applicable Lower Flammable Limit (LFL): Not applicable
Auto Ignition: Not determined Flammability Classification: Not determined
Rate of Burning: Not determined
General Fire Hazards
There is no potential for spontaneous fire or explosion.
Section 6 - Accidental Release Measures
Containment Procedures
Dam, mop, absorb onto sawdust or other absorbent, and place in suitable container.
Clean-Up Procedures
No additional information available.
Section 7 - Handling and Storage
Handling Procedures
Use protective equipment as described in Section 8 of this material safety data sheet when handling uncontained material.
Storage Procedures
Warehouse storage should be in accordance with package directions, if any. Do not freeze. Do not store in temperatures
greater than 120掳F/49掳C.
Section 8 - Exposure Controls / Personal Protection
Exposure Guidelines
A: General Product Information
No information available for the product.
B: Component Exposure Limits
ACGIH, OSHA, and NIOSH have not developed exposure limits for any of this product's components.
PERSONAL PROTECTIVE EQUIPMENT
Personal Protective Equipment: Eyes/Face
Wear safety glasses with side shields.
Personal Protective Equipment: Skin
Neoprene gloves are recommended.
Personal Protective Equipment: Respiratory
Not required under normal operating conditions. Where vapors and/or mists may occur, wear a properly fitted NIOSH
approved half-mask, air purifying respirator.
Personal Protective Equipment: General
No additional information available.
Section 9 - Physical & Chemical Properties
Appearance: Odor:
Light amber colored liquid Slight acrylic odor
Physical State: pH:
Liquid Not determined
Vapor Pressure: Vapor Density:
Not applicable Not applicable
Boiling Point: Melting Point:
Not applicable Not applicable
Solubility (H2O): Specific Gravity:
Nil Not applicable
Freezing Point: Evaporation Rate:
Not applicable Not applicable
Viscosity: Percent Volatile:
Not applicable 85-95% water
VOC: Not applicable
____________________________________________________________
Page 2 of 4 Issue Date: 08/07/2006 Revision: 1.0000
Material Name: JM Building Insulation Binder Material Safety Data
Sheet ID: 1035
Section 10 - Chemical Stability & Reactivity Information
Chemical Stability
This is a stable material. This product is not reactive.
Incompatibility
None known
Hazardous Decomposition
Thermal decomposition may yield acrylic monomers.
Hazardous Polymerization
Will not occur.
Section 11 - Toxicological Information
Acute Toxicity
A: General Product Information
No additional information available.
B: Component Analysis - LD50/LC50
Water (7732-18-5)
Oral LD50 Rat: >90 mL/kg
Carcinogenicity
A: General Product Information
No additional information available.
B: Component Carcinogenicity
None of this product's components are listed by ACGIH, IARC, OSHA, NIOSH, or NTP.
Chronic Toxicity
No additional information available.
Section 12 - Ecological Information
Ecotoxicity
A: General Product Information
No data available for this product.
B: Component Analysis - Ecotoxicity - Aquatic Toxicity
No ecotoxicity data are available for this product's components.
Section 13 - Disposal Considerations
US EPA Waste Number & Descriptions
A: General Product Information
Comply with state and local regulations for disposal. If you are unsure of the regulations, contact your local Public Health
Department, or the local office of the EPA.
B: Component Waste Numbers
No EPA Waste Numbers are applicable for this product's components.
Disposal Instructions
Dispose of waste material according to Local, State, Federal, and Provincial Environmental Regulations.
Section 14 - Transportation Information
International Transportation Regulations
This product is not classified as a hazardous material for transport.
Section 15 - Regulatory Information
US Federal Regulations
A: General Product Information
SARA 311/312: This product is not classified as hazardous under SARA 311/312.
B: Component Analysis
None of this products components are listed under SARA Section 302 (40 CFR 355 Appendix A), SARA Section 313 (40 CFR
372.65), or CERCLA (40 CFR 302.4).
Component Analysis - State
None of this product's components are listed on the state lists from CA, FL, MA, MN, NJ, or PA.
____________________________________________________________
Page 3 of 4 Issue Date: 08/07/2006 Revision: 1.0000
Material Name: JM Building Insulation Binder Material Safety Data
Sheet ID: 1035
A: TSCA Status
This product and its components are listed on the TSCA 8(b) inventory.
None of the components listed in this product are listed on the TSCA Export Notification 12(b) list.
B: Component Analysis - Inventory
Component CAS # TSCA DSL EINECS
Water 7732-18-5 Yes Yes Yes
Component Analysis - WHMIS IDL
No components are listed in the WHMIS IDL.
Section 16 - Other Information
Other Information
Prepared for:
Johns Manville
Building Insulation Division
P.O. Box 5108
Denver, CO 80217-5108
Prepared by:
Johns Manville Technical Center
P.O. Box 625005
Littleton, CO USA 80162-5005
As of the date of preparation of this document, the foregoing information is believed to be accurate and is provided in good
faith to comply with applicable federal and state law(s). However, no warranty or representation with respect to such
information is intended or given.
The information herein is presented in good faith and believed to be accurate as of the effective date given. However, no
warranty, expressed or implied, is given. It is the buyer's responsibility to ensure that its activities comply with Federal, State or
provincial, and local laws.
Date MSDS # Reason
03/20/06 1035-1.0000 New MSDS authoring system.
This is the end of MSDS # 1035
____________________________________________________________
Page 4 of 4 Issue Date: 08/07/2006 Revision: 1.0000
|