PRODUCT DATA
1200
Everlastic Elastomeric Coating
100% ACRYLIC 鈥? SMOOTH TEXTURE 鈥? EXTERIOR 鈥? FLAT 鈥? 1200 LINE
Vehicle Type
Product Description Waterborne 鈥? 100% Acrylic
Everlastic Elastomeric Coating is a superior quality exterior 100% acrylic
Finish
latex flat waterproofing coating designed for use in residential, architectural,
commercial and light industrial applications on a variety of above grade Flat 鈥? 85掳 Sheen - 1.0 to 5.0
vertical masonry surfaces. The exceptionally high content of zinc oxide
Use
and organic mildewcides, combined with high volume solids, give
Exterior
Everlastic Elastomeric Coating the ultimate protection against mildew.
Everlastic Elastomeric Coating has the unique ability to seal and bridge Percent Solids By Weight
hairline cracks in masonry surfaces. Its 鈥渟tretchability鈥? provides the 66.0% 卤 2%
exceptional ability to adjust with movement of the masonry surface
Percent Solids By Volume
caused by expansion and contraction.
53.0% 卤 2%
Performance Suggested Coverage
鈥? Exceptional resistance to blistering, cracking, chipping and peeling 85-170 SFPG
鈥? Extremely good resistance to wind driven rain
Dry Film Thickness
鈥? Extremely good moisture vapor transmission 10.0 mils @ 85 SFPG
鈥? High hiding and excellent coverage 5.0 mils @ 170 SFPG
鈥? Outstanding resistance to mildew and organic growth * See chart on back
鈥? Easy to apply with exceptional long term durability Viscosity
鈥? Outstanding chalk resistance 125 KU 卤 5
鈥? Excellent color retention
Flash Point
Non-flammable 鈥? >200掳 F.
May be applied to properly primed and prepared鈥?
VOC
鈥? Concrete, Masonry and Stucco including:
Contains .47 lbs./gal. (56 gms./ltr.)
Cement Plaster 鈥? Concrete Masonry Units (CMU)
鈥?
Complies with all Federal, State
and Local VOC standards.
鈥? Poured and Precast Concrete
鈥? Synthetic Masonry Stucco (EIFS) Application Equipment
Brush, roller, airless or
Specification Standards conventional spray
鈥? Exceeds Federal Specification for resistance to wind driven rain:
Drying Time
TT-C-555B section 3.3.3.
At 75掳F. / 50% RH
鈥? Passes ASTM D2370 - 450% Elongation at Break / 360 psi Tensile Strength 1 hour to touch
4 hours to recoat
鈥? Moisture Vapor Transmission - ASTM E96-80: Perm Rating 6
Colors
鈥? Meets or exceeds Florida Department of Education Standard MP-21.0 White, off whites, pastels, light
colors, medium colors and special
factory colors.
Limitations
Products Included in This Line
Not recommended for steps, walkways, or other foot or vehicle traffic
areas. Do not use on any horizontal surface including ceilings. Do not use 1200 - White
on decorative, planter or perimeter walls. Do not use for immersion 1201 - Tint White
service or substrates constantly in contact with moisture. Do not apply
below grade, where hydrostatic pressure is expected or where a failure
from water intrusion may occur. Do not use in highly corrosive or
chemical environments, or areas subject to intense heat.
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 1
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Exterior Paints & Coatings
www.colorwheelpaint.com
09900
2001.1 / PDS / 1
1200 LINE EVERLASTIC ELASTOMERIC COATING 鈥? 100% ACRYLIC 鈥? SMOOTH TEXTURE 鈥? EXTERIOR 鈥? FLAT
Surface Preparation General Application Safety
The performance of this product is critically Mix thoroughly to a uniform consistency before WARNING! HARMFUL IF INHALED. SEE
dependent upon the soundness of the substrate each use. Apply by brush, roller or airless LABEL OR MSDS FOR LIST OF HAZARDOUS
to which it is applied. It has been determined sprayer. Work material vigorously into pores. INGREDIENTS. KEEP OUT OF REACH OF
that as high as 80% of all paint and coating Maintain a wet edge. If roller application is
CHILDREN! May cause eye, skin, nose and
failures may be attributed to improper surface employed on porous surfaces, final passes
throat irritation. To avoid breathing vapors or
preparation. It is essential that the proper steps should be completed in a downward direction
spray mist, open windows and doors or use
be taken before applying this product. to insure a uniform appearance and texture.
other means to insure fresh air entry during
Apply at such a rate as to avoid runs and sags.
General: application and drying. If you experience eye
If airless spray application is employed on
Surface must be completely dry and in sound
porous surfaces, immediate 鈥渂ack rolling鈥? and watering, headaches or dizziness, increase fresh
condition. Surface should be clean and free
鈥渂ack brushing鈥? with wet roller/brush is air or wear respiratory protection (NIOSH/
from dirt, grease, mill oils, rust, mill scale,
recommended to help reduce pinholing and MSHA TC 23C or equivalent) or leave area.
chalky paint, efflorescence, organic growth,
work material into pores. Close container after each use. Avoid contact
mildew, and foreign matter to insure good
Thinning:
adhesion of primers and/or finish coats. with eyes and skin.
Peeling, cracking, and chipping paint Under normal conditions thinning is not
First Aid
should be removed by sandblasting, power recommended.
tool cleaning, hand tool cleaning, pressure If you experience difficulty in breathing, leave
Clean-Up:
washing, scraping, or wire brushing. All
the area to obtain fresh air. If continued difficulty
Clean all tools and equipment with warm,
glossy surfaces should be sanded or
is experienced, get medical assistance
soapy water immediately after use. Flush spray
de-glossed. Feather sand rough edges of
immediately. In case of eye contact, flush
previously painted surfaces and spot prime equipment thoroughly.
immediately with large amounts of fresh water
bare areas. Any deteriorated or failed sealant
Application Equipment
and/or patching compound should be for at least 15 minutes and get medical attention;
removed and replaced. All unpainted for skin, wash thoroughly with soap and water.
Brush: Use a quality nylon or polyester brush.
substrates should be properly prepared If swallowed, DO NOT INDUCE VOMITING.
Roller: Use lambswool or synthetic cover: 1/2"
according to respective manufacturer鈥檚 and/or Get medical attention immediately.
to 1 1/4" nap, depending on surface texture.
supplier鈥檚 recommendations. Thoroughly
Storage and Handling
review and follow Color Wheel 鈥淪urface Airless Spray: Use a minimum 0.23" tip. Tip
Preparation Guidelines鈥? and/or Color Wheel
size should reflect equipment type and pressure, Keep from freezing or exposure to intense heat.
written specification before applying.
applicator technique and surface conditions. Do not transfer contents to unlabeled container.
Recommended Primers Adjust pressure for constant and proper
Technical Services
atomization.
New Masonry and Stucco: Hot stucco (three (3)
days after stucco application or with a pH Color Wheel Paints and Coatings offers and
Curing
Range of between 8-12) use 1252 Quick Cure encourages the use of our free technical
Acrylic Conditioner. Prime alkaline masonry Drying time and curing will affect the service. We also advise you to contact us
(pH Range: 8-10) with 330 Optima All Prime, performance of the product. Do not apply regularly for updates to this and other
335 Tropicoat Masonry Primer or 952 Fas-Gard when air, surface or product temperatures are technical data. For technical assistance, to
Conditioner. Prime non-alkaline masonry with
below 50藲 F. or above 100藲 F. Surface arrange a consultation with a Sales
330 Optima All Prime, 335 Tropicoat Masonry
temperature must be at least 5藲 F. above dew Representative, or for current technical data,
Primer or self prime. Prime porous masonry
point. Plan ahead and avoid applying when
with 250 Ti-Gard Masonry Filler or 3250 consult your yellow pages for the Color
damp or threatening weather is expected.
Hi-Build Block Filler. Wheel location nearest you, or call toll free
Product must cure at least 8 hours before being
Previously Painted Masonry and Stucco: Prime (800) 749-6810.
subjected to moisture. During extremely warm
chalky surfaces with 950 Ti-Gard Conditioner,
1250 Ti-Gard Latex Conditioner or 1252 Quick weather, maintaining a wet edge may become
Cure Acrylic Conditioner. Surfaces in good difficult. Avoid application during the heat of
condition may be self primed when properly the day. During cool weather, be aware of
prepared.
possible surfactant leaching. Do not apply late
Synthetic Masonry Stucco (EIFS): Prime with in the day where dew or condensation may
330 Optima All Prime, 1250 Ti-Gard Latex
form before product begins to cure. Allow this
Conditioner or 1252 Quick Cure Acrylic
product to cure a minimum of 30 days before
Conditioner. Surfaces in good condition may
cleaning.
be self primed when properly prepared.
**ELONGATION OF ELASTOMERIC COATING
*The dry film thickness rates listed are theoretical because of the individual system total uniform dry film thickness, porosity and texture of the surface and the
application method. These factors will directly affect the amount of film thickness and coverage rate for each coat. The ability of the coating to bridge various crack
widths directly correlates with the total uniform dry film thickness of the system achieved during the application process and the elongation of the product. Refer
to the chart below.
WIDTH 500% 475% 450% 425% 400% 375% 350% 325% 300% 275% 250%
OF CRACK
Inches = Mils Uniform Mils DFT of Coating System Required To Bridge Crack
1/64 15.6 3.1 3.3 3.5 3.7 3.9 4.2 4.5 4.8 5.2 5.7 6.3
1/32 31.3 6.3 6.6 6.9 7.4 7.8 8.3 8.9 9.6 10.4 11.4 12.5
3/64 46.9 9.4 9.9 10.4 11.0 11.7 12.5 13.4 14.4 15.6 17.0 18.8
1/16 62.5 12.5 13.2 13.9 14.7 15.6 16.7 17.9 19.2 20.8 22.7 25.0
5/64 78.1 15.6 16.4 17.4 18.4 19.5 20.8 22.3 24.0 26.0 28.4 31.3
3/32 93.8 18.8 19.7 20.8 22.1 23.4 25.0 26.8 28.8 31.3 34.1 37.5
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2001.1 / PDS / 2
|