PRODUCT DATA
123
Optima Acrythane Spar Varnish
PREMIUM 鈥? URETHANE ACRYLIC 鈥? INTERIOR 鈥? HIGH-GLOSS 鈥? 123
Vehicle Type
Product Description Waterborne 鈥? Urethane Acrylic
Optima Acrythane Spar Varnish is a superior quality interior high gloss
Finish
clear urethane acrylic varnish designed for use in residential, architectural,
High Gloss 鈥? 60掳 Gloss - 70 to 90
commercial and light industrial applications on a variety of properly
Use
prepared wood surfaces.
Interior
Performance
Percent Solids By Weight
鈥? 32% 卤 2%
Resistant to moisture vapor
鈥? Excellent mar resistance
Percent Solids By Volume
鈥? Rapid dry
30% 卤 2%
鈥? Washable
鈥? Good Adhesion Suggested Coverage
300-500 SFPG
May be applied to properly prepared...
Dry Film Thickness
鈥? Wood Surfaces including: 1.2 mils @ 400 SFPG
鈥? Beams
Viscosity
鈥? Lumber
50 KU 卤 5
鈥? Trim
鈥? Doors Flash Point
鈥? Non-flammable 鈥? >200掳 F.
Cabinets
鈥? Shelving
VOC
鈥? Furniture Contains 1.9 lbs./gal. (227 gms./ltr.)
Complies with all Federal, State
Limitations and Local VOC standards.
For interior use only. Not recommended for steps, walkways, or other foot Application Equipment
Brush, roller, airless or
or vehicle traffic areas. Do not use on substrates constantly in contact with
conventional spray
moisture. Do not use in corrosive or chemical environments, or areas
subject to intense heat. Drying Time
At 75掳F. / 50% RH
1 hour to touch
4 hours to recoat
Colors
Clear
Products Included in This Line
123 - Clear
COLOR WHEEL PAINT MANUFACTURING COMPANY, INC.
Product Index 鈥? Category 5
2814 Silver Star Road 鈥? Orlando, Florida 32808
407-293-6810 鈥? 800-749-6810 鈥? Fax 407-293-0945
Interior Stains & Varnishes
www.colorwheelpaint.com
09900
2001.1 / PDS / 1
123 OPTIMA ACRYTHANE SPAR VARNISH 鈥? PREMIUM 鈥? URETHANE ACRYLIC 鈥? INTERIOR 鈥? HIGH-GLOSS
Surface Preparation General Application Safety
The performance of this product is critically Mix thoroughly to a uniform consistency before WARNING! HARMFUL IF INHALED.
dependent upon the soundness of the substrate each use. Apply by brush, roller or airless SEE LABEL OR MSDS FOR LIST OF
to which it is applied. It has been determined sprayer. Work material vigorously into pores. HAZARDOUS INGREDIENTS. KEEP OUT
that as high as 80% of all paint and coating Maintain a wet edge. If roller application is OF REACH OF CHILDREN! May cause eye,
failures may be attributed to improper surface employed on porous surfaces, final passes skin, nose and throat irritation. To avoid
preparation. It is essential that the proper steps should be completed in a downward direction breathing vapors or spray mist, open windows
be taken before applying this product. to insure a uniform appearance and texture. and doors or use other means to insure fresh
Apply at such a rate as to avoid runs and sags. air entry during application and drying. If
General:
Surface must be completely dry and in sound If airless spray application is employed on you experience eye watering, headaches or
condition. Surface should be clean and free porous surfaces, immediate 鈥渂ack rolling鈥? and dizziness, increase fresh air or wear
from dirt, grease, mill oils, rust, mill scale, 鈥渂ack brushing鈥? with wet roller/brush is respiratory protection (NIOSH/MSHA TC 23C
chalky paint, efflorescence, organic growth, recommended to help reduce pinholing and or equivalent) or leave area. Close container
mildew, and foreign matter to insure good work material into pores. after each use. Avoid contact with eyes and
adhesion of primers and/or finish coats. skin.
Thinning:
Peeling, cracking, and chipping paint First Aid
Under normal conditions thinning is not
should be removed by sandblasting, power recommended. If you experience difficulty in breathing,
tool cleaning, hand tool cleaning, pressure Clean-Up: leave the area to obtain fresh air. If continued
washing, scraping, or wire brushing. All Clean all tools and equipment with warm, difficulty is experienced, get medical
glossy surfaces should be sanded or soapy water immediately after use. Flush spray assistance immediately. In case of eye
de-glossed. Feather sand rough edges of equipment thoroughly. contact, flush immediately with large
previously painted surfaces and spot prime Application Equipment amounts of fresh water for at least 15 minutes
bare areas. Any deteriorated or failed sealant and get medical attention; for skin, wash
Brush: Use a quality nylon or polyester brush.
and/or patching compound should be thoroughly with soap and water. If
Roller: Use lambswool or synthetic cover:
removed and replaced. swallowed, DO NOT INDUCE VOMITING.
3/16" to 3/4" nap, depending on surface texture.
All unpainted substrates should be properly Get medical attention immediately.
Airless Spray: Use a tip size of between 0.09"
prepared according to respective
Storage and Handling
and 0.013". Tip size should reflect equipment
manufacturer鈥檚 and/or supplier鈥檚
type and pressure, applicator technique and Keep from freezing or exposure to intense
recommendations. Thoroughly review and
surface conditions. Adjust pressure for constant heat. Do not transfer contents to unlabeled
follow Color Wheel 鈥淪urface Preparation
and proper atomization. container.
Guidelines鈥? and/or Color Wheel written
Curing Technical Services
specification before applying.
Drying time and curing will affect the Color Wheel Paints and Coatings offers
performance of the product. Do not apply and encourages the use of our free
when air, surface or product temperatures are technical service. We also advise you to
below 50藲 F. or above 100藲 F. Surface contact us regularly for updates to this
temperature must be at least 5藲 F. above dew and other technical data. For technical
point. Plan ahead and avoid applying when assistance, to arrange a consultation with
damp or threatening weather is expected. a Sales Representative, or for current
Product must cure at least 8 hours before being technical data, consult your yellow pages
subjected to moisture. During extremely warm for the Color Wheel location nearest you,
weather, maintaining a wet edge may become or call toll free (800) 749-6810.
difficult. Avoid application during the heat of
the day. During cool weather, be aware of
possible surfactant leaching. Do not apply late
in the day where dew or condensation may
form before product begins to cure. Allow this
product to cure a minimum of 30 days before
cleaning.
All technical advice, recommendations, and services are rendered by Color Wheel gratis. They are based on technical data which Color Wheel believes to be reliable, and are intended for use by persons having skill and knowhow at their own discretion and risk.
Color Wheel Paint Manufacturing Company, Inc. assumes no responsibility for results obtained or damages incurred from their use by purchaser/user in whole or in part. All information is subject to change without notice.
NOTE: Where applicable, and for consistency, technical data and test results contained in this document are based on the pure white base of the particular product line.
LIMITATION OF LIABILITY: COLOR WHEEL MAKES NO WARRANTY OR GUARANTEE OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Liability, if any, is limited to replacement of the product or refund of the purchase price. LABOR OR COST OF LABOR AND OTHER CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED.
09900 2001.1 / PDS / 2
|