MATERIAL SAFETY DATA SHEET
EMERGENCY TELEPHONE 800-424-9300 (Chemtrec) Health : 3
Lonza Inc. 90 Boroline Road Allendale NJ 07401 Flammability : 2
800-777-1875 (9am - 5pm) 309-697-7200 (After 5pm) Reactivity : 0
95324 Bardac 2250 PAGE 1 OF 7
************************************************************************************
MATERIAL DATE ISSUED DOT HAZARD CLASSIFICATION
Bardac 2250 05/28/04 - Revised 8, PG II
DOT SHIPPING NAME
CAS. NO. Mixture Disinfectant Liquid Corrosive N.O.S.
SUPERCEDES
04/23/96 DOT LABEL Corrosive and Flammable
Mixture
FORMULA
(Active) Didecyl dimethylammonium chloride
CHEMICAL NAME
****************************** I - INGREDIENTS *************************************
APPROXIMATE
WEIGHT % TWA/TLV
N-,N-Didecyl-N,N-dimethylammonium chloride 50 None established
(CAS No. 7173-51-5)
Ethanol (CAS No. 64-17-5) 10 1000 ppm (OSHA-PEL}
1000 ppm (ACGIH-TWA)
Water (CAS No. 7732-18-5) 40 None established
********************** II - PHYSICAL AND CHEMICAL PROPERTIES ***********************
APPEARANCE Colorless to pale yellow liquid pH 6.5 to 9.0 (10% active solution)
VISCOSITY < 100 cps at 25oC ODOR Ethanol-like
MELTING OR FREEZING POINT -20oC
BOILING POINT Not known
VAPOR DENSITY (Air=1) Not known VAPOR PRESSURE (mm Hg) Not known
PERCENT VOLATILE (by weight) 50 SOLUBILITY IN WATER Soluble
SPECIFIC GRAVITY (Water=1) 0.93/cm3 @ 25oC
EVAPORATION RATE (Butyl Acetate=1) Not
known
*********************** III - FIRE AND EXPLOSION INFORMATION ***********************
FLASH POINT ~ 109掳F (Setaflash close cup) AUTO IGNITION TEMPERATURE Not known
LOWER EXPLOSION LIMIT (%) Not known UPPER EXPLOSION LIMIT (%) Not known
ALCOHOL FOAM X CO2 X
EXTINGUISHING MEDIA FOAM
DRY CHEMICAL X WATER X OTHER
SPECIAL FIRE FIGHTING PROCEDURES:
Must wear NIOSH/MSHA approved self-contained breathing apparatus and protective
clothing. Cool fire-exposed containers with water spray.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Products of combustion are toxic. Heated solvent vapors can travel to an ignition
source and flash back.
The information provided herein is compiled form internal reports and data form professional publications. IT IS FURNISHED WITHOUT WARRANTY OF ANY
KIND, EXPRESSED OR IMPLIED. It is intended to assist in evaluating the suitability and proper use of the material in manufacturing and in the development and
implementation of safety precautions and procedures.
MATERIAL SAFETY DATA SHEET
EMERGENCY TELEPHONE 800-424-9300 (Chemtrec)
Lonza Inc. 90 Boroline Road Allendale NJ 07401 800-777-1875 (9am - 5pm) 309-697-7200 (After 5pm)
95324 Bardac 2250 PAGE 2 OF 7
************************ IV - HEALTH EFFECTS INFORMATION ***************************
ROUTES OF ENTRY - SKIN CONTACT X EYE CONTACT X
X
INHALATION INGESTION
EFFECTS OF OVEREXPOSURE
Based on the available animal toxicity information for this and closely related
materials, it is anticipated that direct skin or eye contact may produce severe
irritation and/or burns with possible irreversible damage. May be fatal if ingested.
Ingesting can cause immediate burning pain in the mouth, throat and abdomen; resulting
in severe swelling of the epiglottal tissue of the larynx. Ingestion can also result in
muscular paralysis affecting the ability to breathe; causing circulatory shock and/ or
convulsions. Inhalation of solvent vapors or aerosol mists can cause irritation of the
mucous membranes. Prolonged inhalation of solvent vapors may produce drowsiness,
lassitude and inability to concentrate.
OVEREXPOSURE MAY AGGRAVATE EXISTING CONDITIONS:
No effects indicated.
EMERGENCY AND FIRST AID PROCEDURES:
For eyes contact, immediately flush eyes with large amounts of running water for at
least 15 minutes. Hold eyelids apart to ensure rinsing of the entire surface of the
eye and lids with water. Get immediate medical attention. If physician not available,
flush for additional 15 minutes and then transport victim to medical care.
For skin contact, wash with plenty of running water, and soap if available, for 15
minutes. Remove contaminated clothing and shoes. Get immediate medical attention.
Wash clothing and decontaminate shoes before reuse.
If swallowed, immediately give 3-4 glasses of milk (if unavailable, give water). DO
NOT induce vomiting. If vomiting does occur, give fluids again. Get immediate medical
attention. Have physician determine if patient's condition allows for induction of
vomiting or evacuation of the stomach. Do not give anything by mouth to a convulsing
or unconscious person. (See "Note to Physician" in Section X).
If inhaled, remove from area to fresh air. Get immediate medical attention. If not
breathing, clear airway and start artificial respiration. If victim is having trouble
breathing, give supplemental oxygen, if available.
CHEMICALS LISTED AS CARCINOGEN BY:
NATIONAL TOXICOLOGY PROGRAM - No
- No
I.A.R.C. MONOGRAPHS
- No
OSHA
NOTE TO PHYSICIAN:
Probable mucosal damage may contraindicate the use of gastric lavage. Take measures
against circulatory shock. Breathing may need support, either through use of manually
or mechanically measures. Administer oxygen, if having difficulty with breathing.
*************************** V - REACTIVITY INFORMATION *****************************
X
STABILITY: STABLE CONDITIONS TO AVOID
None known
UNSTABLE
The information provided herein is compiled form internal reports and data form professional publications. IT IS FURNISHED WITHOUT WARRANTY OF ANY
KIND, EXPRESSED OR IMPLIED. It is intended to assist in evaluating the suitability and proper use of the material in manufacturing and in the development and
implementation of safety precautions and procedures.
MATERIAL SAFETY DATA SHEET
EMERGENCY TELEPHONE 800-424-9300 (Chemtrec)
Lonza Inc. 90 Boroline Road Allendale NJ 07401 800-777-1875 (9am - 5pm) 309-697-7200 (After 5pm)
95324 Bardac 2250 PAGE 3 OF 7
*************************** V - REACTIVITY INFORMATION (continued) *****************
HAZARDOUS DECOMPOSITION PRODUCTS
Thermal decomposition may produce toxic vapors/fumes of hydrogen chloride, amines and
other organic materials, and oxides of carbon and nitrogen.
HAZARDOUS POLYMERIZATION CONDITIONS TO AVOID
WILL NOT X None known
MAY
OCCUR OCCUR
INCOMPATIBILITY (MATERIALS TO AVOID)
OTHER X Strong oxidizing or reducing agents.
WATER
************************ VI - SPILL AND DISPOSAL INFORMATION ***********************
STEPS TO BE TAKEN IN CASE OF MATERIAL SPILL OR RELEASE
DANGER! Corrosive and Flammable liquid. Remove all sources of ignition and ground all
equipment before beginning cleanup. Floors may become slippery. Wear appropriate
protective equipment and NIOSH/MSHA approved respirator where mists or vapors of
unknown concentrations may be generated (self-contained breathing apparatus preferred).
Dike and contain spill with inert material (sand, earth, etc.) and transfer the
liquid and solid separately to containers for recovery or disposal. Keep spill out
of sewers and open bodies of water.
WASTE DISPOSAL METHODS
Dispose of in compliance with all Federal, state and local laws and regulations.
Incineration is the preferred method. If burned, stay out of smoke.
CONTAINER DISPOSAL
Triple rinse (or equivalent). Then offer for recycling or reconditioning, or
puncture and dispose of in a sanitary landfill, or incineration, or, if allowed by
state and local authorities, by burning. If burned, stay out of smoke.
*********************** VII - PERSONAL PROTECTION INFORMATION **********************
ENGINEERING CONTROLS
In processes where mists or vapors may be generated, proper ventilation must be
provided in accordance with good ventilation practices.
RESPIRATORY PROTECTION
In processes where mists or vapors may be generated, a NIOSH/MSHA jointly approved
respirator is advised in the absence of proper environmental controls.
PROTECTIVE GLOVES
Rubber or neoprene, to prevent skin contact.
EYE PROTECTION
Wear chemical splash goggles where there is a potential for eye contact. Use safety
glasses with side shields where there is no potential for eye contact.
OTHER PROTECTIVE EQUIPMENT
Eye wash; safety shower; protective clothing (long sleeves, coveralls or other, as
appropriate), when needed, to prevent skin contact.
The information provided herein is compiled form internal reports and data form professional publications. IT IS FURNISHED WITHOUT WARRANTY OF ANY
KIND, EXPRESSED OR IMPLIED. It is intended to assist in evaluating the suitability and proper use of the material in manufacturing and in the development and
implementation of safety precautions and procedures.
MATERIAL SAFETY DATA SHEET
EMERGENCY TELEPHONE 800-424-9300 (Chemtrec)
Lonza Inc. 90 Boroline Road Allendale NJ 07401 800-777-1875 (9am - 5pm) 309-697-7200 (After 5pm)
95324 Bardac 2250 PAGE 4 OF 7
*************************** VIII - STORAGE AND HANDLING ***************************
PRECAUTIONS FOR STORAGE AND HANDLING:
Maximum storage temperature: 140oF. Store containers in compliance with the most
recent NFPA code (NFPA 30). Ground all containers prior to pouring. Keep containers
closed when not in use. Do not contaminate drinking water, food or feed by storage or
disposal.
******************* IX - TOXICOLOGY & ECOTOXICOLOGY INFORMATION ********************
ACUTE
- oral LD50 (rat): 450 mg/kg; 412 mg/kg (males); 292 mg/kg (females)
- dermal LD50 (rabbit): 3342 mg/kg, 4300 mg/kg
- eye irritation (rabbit): Extreme irritation that did not clear by day 7, post dose
- skin irritation (rabbit): Severe irritation that did not clear by day 7, post dose
- skin sensitization (0.2% active solution) (guinea pig): Not a sensitizer
- skin corrosivity (rabbit 鈥? DOT): Corrosive
GENOTOXICITY/MUTAGENICITY
- Ames test (Salmonella sp.): Not mutagenic
- Micronucleus (in vivo -rat): No evidence of chromosomal damage in the bone marrow of
rats treated with 600 mg/kg.
- HGPRT (in vitro 鈥? CHO cells): Not clastogenic with or without metabolic activation.
For Didecyldimethylammonium chloride:
- Ames test (Salmonella sp.- on): Not mutagenic
- HGPRT (in vitro 鈥? CHO cells): Not clastogenic with or without metabolic activation.
- unscheduled DNA synthesis (in vitro): Not mutagenic with or without metabolic
activation.
REPRODUCTIVE/DEVELOPMENTAL
- developmental (rat-oral): No evidence of developmental effects observed at exposure
doses ranging from 10 to 50 mg/kg/day administered from day 6 through 15 of
gestation.
- developmental (rabbit-oral): No evidence of developmental effects observed at
exposure doses ranging from 10 to 50 mg/kg/day administered from day 6 through 15 of
gestation.
REPEATED DOSE
For Didecyldimethylammonium chloride:
- subchronic dermal toxicity (rat - 90 days - feeding): No adverse systemic toxicity
noted.
- chronic oral toxicity (dog - 1 year - feeding): No systemic target organ effects
noted.
ECOTOXICITY
AQUATIC
For Didecyldimethylammonium chloride:
- LC50 (salmon - 96 hour): 1.0 mg/l
- LC50 (bluegill sunfish - 96 hour): 0.32 mg/l
- LC50 (mysid shrimp - 96 hour): 0.069 mg/l
- EC50 (Daphnia magna - 48 hour): 0.94 mg/l
The information provided herein is compiled form internal reports and data form professional publications. IT IS FURNISHED WITHOUT WARRANTY OF ANY
KIND, EXPRESSED OR IMPLIED. It is intended to assist in evaluating the suitability and proper use of the material in manufacturing and in the development and
implementation of safety precautions and procedures.
MATERIAL SAFETY DATA SHEET
EMERGENCY TELEPHONE 800-424-9300 (Chemtrec)
Lonza Inc. 90 Boroline Road Allendale NJ 07401 800-777-1875 (9am - 5pm) 309-697-7200 (After 5pm)
95324 Bardac 2250 PAGE 5 OF 7
********** X - MISCELLANEOUS AND REGULATORY INFORMATION (continued)***************
INTERNATIONAL LEVEL REGULATIONS
INTERNATIONAL INVENTORY STATUS
The components of this product are listed on the following chemical inventory lists:
Australian AICS; Canadian DSL; Chinese SEPA; European Union EINECS; Japanese METI;
Korean ECL; Philippines PICCS and U.S. TSCA.
CANADIAN WORKPLACE HAZARDOUS MATERIAL INFORMATION SYSTEM(WHMIS) CLASSIFICATION
This product has a WHMIS classification of E, B2, D2-B
U.S. FEDERAL LEVEL REGULATIONS:
TOXIC SUBSTANCES CONTROL ACT (TSCA INVENTORY) STATUS:
The components in this product are currently listed on the EPA TSCA 8(b) inventory.
TSCA Section 12(b) Export Notification
Components present in this product which, if exported, could require either annual
or one-time reporting under this regulation are as follows:
Typical Maximum
Chemical Name CAS Number Concentration
None known
EPA REGULATION ON PESTICIDES
This product is an EPA FIFRA registered pesticide, EPA Registration No. 6836-51. It
can only be used commercially in the United States for EPA registered
application(s) listed on the product label.
CERCLA (Comprehensive Environmental Response, Compensation and Liability Act of
1980 requires notification of the National Response Center
(Telephone 800-424-8802) in the event of a release of quantities of the
following hazardous materials contained in this product, if the release is
equal to or greater than the Reportable Quantities (RQs) listed in
40 CFR 302.4:
Typical Maximum
Chemical Name CAS Number Concentration
None known
U.S. FEDERAL LEVEL REGULATIONS:
SARA Title III, Sections 302/304 (Superfund Amendments and Reauthorization act of
1986) - This act requires emergency planning, including agency notification, for
possible release of the following components of this material, based upon the
Threshhold Planning Quantities (TPQs) and release Reportable Quantities (RQs)
listed for the Components in 40 CFR 355:
Typical Maximum
Chemical Name CAS Number Concentration
None known
The information provided herein is compiled form internal reports and data form professional publications. IT IS FURNISHED WITHOUT WARRANTY OF ANY
KIND, EXPRESSED OR IMPLIED. It is intended to assist in evaluating the suitability and proper use of the material in manufacturing and in the development and
implementation of safety precautions and procedures.
MATERIAL SAFETY DATA SHEET
EMERGENCY TELEPHONE 800-424-9300 (Chemtrec)
Lonza Inc. 90 Boroline Road Allendale NJ 07401 800-777-1875 (9am - 5pm) 309-697-7200 (After 5pm)
95324 Bardac 2250 PAGE 6 OF 7
******************* X - MISCELLANEOUS AND REGULATORY INFORMATION (continued) ********
SARA Title III Sections 311/312 - This act requires reporting under the Community
Right-to-Know provisions due to the inclusion of the following components of this
material in one or more of the five hazard categories listed in 40 CFR 370:
Hazard *)
Chemical Name CAS Number Categories
N,N-Didecyl-N,N-dimethylammonium chloride 7173-51-5 A
Ethanol 64-17-5 F
*) The five hazard categories are as follows: F=FIRE HAZARD; S= SUDDEN RELEASE OF
PRESSURE; R=REACTIVE; A=IMMEDIATE (ACUTE) HEALTH HAZARD; C=DELAYED (CHRONIC)
HEALTH HAZARD
SARA Title III Section 313 - This act requires submission of annual reports of
releases of the following components of this material if the threshold reporting
quantities as listed in 40 CFR 372, are met or exceeded:
Typical Maximum
Chemical Name CAS Number Concentration
None known
STATE RIGHT-TO-KNOW REGULATIONS:
CALIFORNIA PROPOSITION 65 - Components present in this material which the State of
California has found to cause cancer, birth defects or other reproductive harm
are as follows:
AS A CANCER HAZARD Typical Maximum
Chemical Name CAS Number Concentration
Acetaldehyde 75-07-0 1 ppm
N-Nitrosodimethylamine 62-75-9 100 ppb
MASSACHUSETTS Right-to-Know - The following components of this material are included
in the Massachusetts Substance List and are present at or above reportable
levels:
Typical Maximum
Chemical Name CAS Number Concentration
Acetaldehyde 75-07-0 1 ppm
Ethanol 64-17-5 10%
MICHIGAN Critical Materials - The following components of this material are included
in the Michigan Critical Materials List:
Chemical Name CAS Number
None known
NEW JERSEY Right-to-Know - The following components of this material are included in
the New Jersey Hazardous Substance List and are present at or above reportable
levels:
Typical Maximum
Chemical Name CAS Number Concentration
N,N-Didecyl-N,N-dimethylammonium chloride 7173-51-5 50%
Ethanol 64-17-5 10%
The information provided herein is compiled form internal reports and data form professional publications. IT IS FURNISHED WITHOUT WARRANTY OF ANY
KIND, EXPRESSED OR IMPLIED. It is intended to assist in evaluating the suitability and proper use of the material in manufacturing and in the development and
implementation of safety precautions and procedures.
MATERIAL SAFETY DATA SHEET
EMERGENCY TELEPHONE 800-424-9300 (Chemtrec)
Lonza Inc. 90 Boroline Road Allendale NJ 07401 800-777-1875 (9am - 5pm) 309-697-7200 (After 5pm)
95324 Bardac 2250 PAGE 7 OF 7
******************* X - MISCELLANEOUS AND REGULATORY INFORMATION (continued) ********
PENNSYLVANIA Right-to-Know - The following components of this material are included
in the Pennsylvania Hazardous Substance List and are present at or above
reportable levels:
Typical Maximum
Chemical Name CAS Number Concentration
Ethanol 64-17-5 10%
The information provided herein is compiled form internal reports and data form professional publications. IT IS FURNISHED WITHOUT WARRANTY OF ANY
KIND, EXPRESSED OR IMPLIED. It is intended to assist in evaluating the suitability and proper use of the material in manufacturing and in the development and
implementation of safety precautions and procedures.
|