Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: msds_carboline_com---phenoline311pds9-07.asp
                                                                                                                                            Phenoline 311
(fka: Carboguard 622)




Selection & Specification Data Substrates & Surface Preparation
Generic Type Micaceous iron oxide filled epoxy phenalkamine General Remove any oil or grease from surface to be
coated with clean rags soaked in Carboline Thinner
Description A tank lining holding primer that has a variety of #2, or toluol.
attributes including low-temperature cure, fast recoat
times, moisture tolerance during application and cure,
and excellent blast-hold protection. Phenoline 311 can Steel For immersion applications: Abrasive blast to a
also be used direct to metal as a corrosion resistant Substrates Near-White Metal Finish in accordance with SSPC-
primer and is suitable for both new tanks and relines. SP 10 and obtain a 1.5-2 mil blast profile.
It exhibits excellent surface wetting characteristics and
For non-immersion applications: Abrasive blast to
quick cure for handling. It contains high levels of inert
a Commercial Finish in accordance with SSPC-SP 6
flake reinforcement.
and obtain a 1½-2 mil (40-75 micron) blast profile for
moderate to severe exposures. For mild
Features Low temperature cure (20°F)
environments, Hand Tool or Power Tool clean in
Excellent blast-hold protection
accordance with SSPC-SP 2, SSPC-SP 3, or SSPC-
Excellent application characteristics
SP 11 to produce a rust-scale free surface.
Fast recoat times
Moisture tolerance during application
Meets VOC restrictions
Low HAP’s content
Ordering Information
Gloss Flat Prices may be obtained from Carboline Sales Representative or
Main Office. Terms � Net 30 days.
Color Red 1 Gal. Kit 5 Gal. Kit
Shipping
15.0 lbs. (6.8 kg) 78 lbs. (35.5 kg)
Primers Self-Priming Weight
(approx)
Topcoats Topcoat selection will depend on exposures

Application Equipment
Dry Film For most applications: 2.0-3.0 mils (50-75 microns)
Thickness per coat Listed below are the general equipment guidelines for the
application of this product. Job site conditions may require
Solids Content Theoretical solids (mixed) by volume: modifications to these guidelines to achieve the desired results.
SBV: 47 +/- 2%
Spray Hold gun 12-14 inches from the surface and at
Application a right angle to the surface.
Theoretical 754 mil ft² ( 18.5 m²/l at 25 microns)
Coverage Rates 301 sq. ft. at 2.5 mils (7.4 sq. m/l @ 62 microns)
NOTE: Material losses during mixing and
Airless Spray Pump Ratio: 45:1 (min.)
applications will vary and must be taken into
Volume Output: 11.5 l/min min.
consideration when estimating job requirements.
(2.5gpm min.)
Material Hose: 12.5mm min.
Dry Temp. Continuous: 180°F (82°C)
(½� I.D. min.)
Resistance Non-Continuous: 220°F (104°C)
Tip Size: 0.43-0.53mm
(0.017-0.021�)
VOC Values As supplied: 2.80 lbs/gal (336 g/l) mixed
140-175kg/cm²
(calculated) May be thinned up to 6 oz/gal with Thinner 2 or Output Pressure:
(2000-2500 psi)
Thinner 225E.
Use a 1/2� minimum I.D. material hose
These are nominal values and may vary with color.
The following spray equipment has been found
suitable and is available from manufacturers
HAP’s Values 1.79 lbs./solid gallon
such as Binks, DeVilbiss and Graco.
Mfr. & Gun Pump*
Limitations Epoxies lose gloss, discolor and eventually chalk
Use either model below: Huskie
in sunlight exposure.
Graco 207-300 (DeVilbiss)
Binks Model 520 Bulldog 45:1
Jupiter 8D
*Teflon packings are recommended and
available from pump manufacturer.




September 2007 replaces April 2007 N 0621
To the best of our knowledge the Technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify
correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage,
performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR
IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carboxane® are registered
trademarks of Carboline Company.
Phenoline 311
Pressure pot equipped with dual regulators, 3/8�
Conventional
Curing Schedule
I.D. minimum material hose, .070� I.D. fluid tip and
Spray
appropriate air cap.
For nominal film thicknesses (2-3 mils)
For applications over damp surfaces, brush and
Brush or Surface Dry to
roller is the preferred method. Multiple coats may
Roller Maximum
Temperature Topcoat
be required to obtain desired appearance, @ 50% RH minimum Dry to Handle recoat time
recommended dry film thickness, and adequate 20°F (-7°C) 24 hours 36 Hours 45 days
hiding. Avoid excessive re-brushing or re-rolling. 35°F (2°C) 2 Hours 16 Hours 45 days
For best results, tie-in within 10 minutes at 75°F
50°F (10°C) 1 hours 10 Hours 30 days
(24°C). Use a short-nap synthetic roller cover with
75°F (24°C) 30 Minutes 3 Hours 30 days
phenolic core
90°F (32°C) 30 Minutes 1.5 Hours 15 days

Mixing & Thinning These times are based on a 2-3 mil (50-75 micron) dry film
Thickness per coat. Higher film thickness, insufficient ventilation or cooler
temperatures will require longer cure times and could result in solvent
Mix separately, then combine and mix in the following
Mixing
entrapment and premature failure. While this product can tolerate excessive
proportions (3:1 ratio):
humidity during curing, check for blush or haze and remove, if present, by
1 Gal. Kit 4 Gal. Kit
water washing before recoating. If the maximum recoat times have been
Part A .75 gallon 3 gallon
exceeded, the surface must be abraded by sweep blasting or sanding prior to
Part B .25 gallon 1 gallon
the application of additional coats. For force curing, contact Carboline
Thinning not normally required. May be thinned up to 6
Technical Service for specific requirements.
oz/gal with Carboline Thinner 2 or exempt Thinner 225E
For application and cure conditions below 35°F, dehumidify before, during,
to maintain VOC. Maintain constant agitation to ensure
and after application to prevent ice formation on the surface.
consistency due to settling. Tip: If spraying is stopped
for more than 10 minutes it is advisable to recirculate the Do not apply to substrates with ice or ice crystal formation. Dehumidify or
material lines back in. For a slower thinner use Thinner raise the temperature to eliminate ice on the substrate.
214.

3 hours at 75°F (24°C) and less at higher temperatures.
Pot Life
Packaging, Handling & Storage
Pot life ends when coating becomes too viscous to use.


Cleanup & Safety Flash Point Part A: 60°F (15°C)
(Setaflash) Part B: 74 °F (23°C)
Use Thinner #2 or Acetone. In case of spillage, absorb
Cleanup
Carboline Thinner 2 -4°F (-20°C)
and dispose of in accordance with local applicable
regulations.
Storage (General) Store Indoors. KEEP DRY
Read and follow all caution statements on this product
Safety
data sheet and on the MSDS for this product. Employ Storage 40 -100°F (4°C-38°C)
normal workmanlike safety precautions. Hypersensitive
Temperature 0-95% Relative Humidity
persons should wear protective clothing, gloves and
& Humidity
use protective cream on face, hands and all exposed
areas.
Shelf Life Part A 12 months at 76°F (24°C)
When used as a tank lining or in enclosed areas,
Ventilation
Part B 24 months at 76°F (24°C)
thorough air circulation must be used during and after
application until the coating is cured. The ventilation
*Shelf Life: (actual stated shelf life) when kept at recommended
system should be capable of preventing the solvent
storage conditions and in original unopened containers.
vapor concentration from reaching the lower explosion
limit for the solvents used. User should test and monitor
exposure levels to insure all personnel are below
guidelines. If not sure or if not able to monitor levels,
use MSHA/NIOSH approved supplied air respirator.
This product contains flammable solvents. Keep away
Caution
from sparks and open flames. All electrical equipment
and installations should be made and grounded in
accordance with the National Electric Code. In areas
where explosion hazards exist, workmen should be
required to use non-ferrous tools and wear conductive
and non-sparking shoes.


Application Conditions
Condition Material Substrate Ambient RH
60°F-75°F 60°F-75°F
60°F� 75°F
Optimum 30-70%
(16°C�24°C) (16°C-24°C) (16°C-24°C)
Minimum 45°F (7°C) 0%
20°F (-7°C) 20°F (-7°C)
Maximum 90°F (32°C) 85%
120°F (50°C) 100°F (35°C)
Industry standards are for substrate temperatures to be above the dew
point. Phenoline 311 is unique in that it can tolerate damp substrates.
See Brush or Roller above. Special thinning and application techniques
may be required above or below normal conditions.




September 2007 replaces April 2007 N
To the best of our knowledge the Technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Carboxane®
are registered trademarks of Carboline Company.

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
msds_carboline_com---phenoline302pds8-05.asp N/A
msds_carboline_com---phenoline311pds9-07.asp N/A
msds_carboline_com---phenoline333pds6-07.asp N/A
msds_carboline_com---phenoline341pds1-08.asp N/A
msds_carboline_com---phenoline379pds4-03.asp N/A
msds_carboline_com---plasite3066pds8-07.asp N/A
msds_carboline_com---plasite3070pds8-03.asp N/A
msds_carboline_com---plasite4007&4007cipds5-05.asp N/A
msds_carboline_com---plasite4100pds1-06.asp N/A
msds_carboline_com---plasite4300pds1-06.asp N/A
msds_carboline_com---plasite4310pds1-06.asp N/A
msds_carboline_com---plasite4500spds5-07.asp N/A
msds_carboline_com---plasite4550pds9-07.asp N/A
msds_carboline_com---plasite4550spds6-06-marine.asp N/A
msds_carboline_com---plasite4555spds5-05-marine.asp N/A
msds_carboline_com---plasite4555spds5-05.asp N/A
msds_carboline_com---plasite4600pds8-03.asp N/A
msds_carboline_com---plasite4600pds8-06-marine.asp N/A
msds_carboline_com---plasite5302arpds5-04.asp N/A
msds_carboline_com---plasite5306pds8-06.asp N/A
msds_carboline_com---plasite5309pds8-03.asp N/A
msds_carboline_com---plasite7102pds2-04.asp N/A
msds_carboline_com---plasite7111pds8-03.asp N/A
msds_carboline_com---plasite7122hspds6-05.asp N/A
msds_carboline_com---plasite7122lpds10-07.asp N/A
msds_carboline_com---plasite7122pds8-06-marine.asp N/A
msds_carboline_com---plasite7133hspds11-04.asp N/A
msds_carboline_com---plasite7159pds1-07.asp N/A
msds_carboline_com---plasite7208pds2-04.asp N/A
msds_carboline_com---plasite797pds3-04.asp N/A
msds_carboline_com---plasite9053pds8-05.asp N/A
msds_carboline_com---plasite9057pds8-03-marine.asp N/A
msds_carboline_com---plasite9060pds8-06-marine.asp N/A
msds_carboline_com---plasite9060pds9-06.asp N/A
msds_carboline_com---plasite9081pds8-03.asp N/A
msds_carboline_com---plasite9085pds8-03.asp N/A
msds_carboline_com---plasite9122pds8-03.asp N/A
msds_carboline_com---plasite9133pds11-07.asp N/A
msds_carboline_com---plasite9145pds8-03.asp N/A
msds_carboline_com---plasite9200harpds2-04.asp N/A
msds_carboline_com---plasite943pds2-04.asp N/A
msds_carboline_com---plasite9500pds7-05.asp N/A
msds_carboline_com---plasite9570&har&tfepds7-08.asp N/A
msds_carboline_com---plasite9571pds10-06.asp N/A
msds_carboline_com---plasite9573pds8-03.asp N/A
msds_carboline_com---polyclad708pds8-07.asp N/A
msds_carboline_com---pyrocote1340pds10-06.asp N/A
msds_carboline_com---pyrocrete239ai7-04.asp N/A
msds_carboline_com---pyrocrete239pds1-06.asp N/A
msds_carboline_com---pyrocrete40pds7-04.asp N/A

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC