Phenoline 333
Clean Up Thinner #2 or Acetone
Selection & Specification Data Solvent
Description Phenoline 333 is a low bake, high solids,
modified epoxy formulated Safe Application Consult MSDS for proper handling,
for use as a protective lining with Conditions cleanup, disposal, and use of personal
excellent resistance to molten sulfur. protective equipment. Circulate sufficient
Excellent chemical and thermal shock air to maintain working environment
resistance. below the PEL and LEL. Apply
according to local, state, and federal
Typical Uses Lining for corrosive immersion (OSHA) regulations.
environments, where commodities
may contain sulfates. Formulated as an
PHYSICAL SPECIFICATIONS
interior lining for resistance
to molten sulfur with effective heat
Finish: Gloss
distribution and heat dissipation.
Color: Black
Dry 325掳F continuously, 350掳F intermittently
Temperature Loading temperatures should be limited Volume Solids: 72% (mixed)
Limits to 300掳F and unloading to 325掳F. Steel
VOC: 2.0 lbs./gal. (mixed); 238 g/l (mixed)
car should be greater than 0掳F when
loaded. Flash Point: 63掳F
Chemical Consult Carboline representative for Mixing Ratio: 4:1 by volume
Resistance specific recommendations.
Total Dry Film Thickness: 5 to 7 mils, 1 coat only (do not apply
dress coat)
Weld NACE RP0178-89, Weld Prep
Preparation Designation C
Wet Film Thickness: 7 to 10 mils
Surface NACE No.2/SSPC-SP10 Near White Theoretical Coverage: 1126 sq.ft./ gal.@ 1 mil
Cleanliness Metal Blast
Induction Time: None
Profile Depth average 2.5 to 3.0 mils (visual
comparator) Pot Life: 70 min. @ 77掳F for 陆 gallon mix
35 min. @ 77掳F for 5 gal. mix
Profile Texture Sharp, angular, and dense (viewed
Shelf Life: 24 months
under magnification)
Dry Time: @ 77掳F (25C)
Application 45:1 ratio pump with 0.017 (617) to 0.019
Dry to Touch 4 hours
Equipment (619) inch diameter orifice for airless Dry to Handle 6 hours
spray gun tip at a 2,800 psi Dry to Recoat 10 hours
recommended minimum fluid pressure at
tip to obtain proper atomization. An artist Air Dry Schedule: Circulate warm air at 85 to 90掳F for 12
hours minimum. All touchups must be made before force cure.
brush can be used for touchup of WFT
marks and other small repair areas.
Force Cure Schedule:
鈥? Ramp rate @ 50 degrees (掳F) every 30 minutes
Application 鈥? Non-contaminated profile (pretreat and
鈥? 150掳F soak temperature @ 4 hours
Conditions blast contaminated surfaces)
鈥? Dry, dust-free metal surface
鈥? Metal temperature above 60掳F
鈥? Metal temperature at least 5 deg.
above the dew point
鈥? Ambient temperature above 50掳F
鈥? Humidity less than 90%
鈥? Material temperature between 70 and
90掳F
Primer Self-Priming 鈥? one coat application only
Thinner Thinner #231
June 2007 replaces April 2007 100R
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline庐 and Carbocrylic庐
are registered trademarks of Carboline Company.
|