SITE® 53 Plasite 5306
Polyamine Cured Epoxy Lining
TYPE
PLASITE 5306 is an ambient cured monolithic liner formulated for PHYSICAL SPECIFICATIONS
optimum chemical and abrasion resistance in extremely corrosive
atmospheres or continuous immersion service. Compressive Strength…â?¦â?¦â?¦â??..3,000 - 15,000 psi
(ASTM D659)
INTENDED USE
6
Not intended where aesthetics are a concern. Heavy-duty lining for: Modulus of Elasticity…â?¦â?¦â?¦â?¦â?¦â?¦â??.â€?1.312 x 10
(ASTM D695)
Trough Walls
Ventilating Systems
Tensile Strength…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??..1500 - 2500 psi
Foundations
Fourdrinier Pits
(ASTM D638)
Cyclones
Conveyor Troughs
Sand Hoppers
Conveying Tunnels
Flexural Strength…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??.5300 - 6000 psi
Clarifiers
Pumps
(ASTM DC90)
Metal Pans
Chutes
Trenches
Tanks
Thermal Coefficient of Linear Expansion
Acid Pits
-6
…â?¦â?¦â?¦â?¦â??.â€?....…â??9.16 x 10 in/in/°F(ASTM D696)
ADVANTAGES Solids…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??100%
Cures quickly to form an exceptionally tough, impact and abrasion
resistant surface. Excellent adhesion to concrete, steel and wood. CHEMICAL RESISTANCE
Minimum down time. Non-shrinking.
Not affected by water, oil, brine, most acids and alkalies. For specific
COLOR: 5306 comes in a non-pigmented formula only. Resin chemical resistance properties, refer to PLASITE Bulletin TD-5.
appears clear to an amber-green color. Aggregate coloration will
show through.
SURFACE PREPARATION APPLICATION TEMPERATURE
New Concrete Do not apply when surface temperature is below 40°F/4°C For
New concrete must have a minimum of 28 days cure and no curing application, the material must be 70-85°F/21°-29°C.
agents or sealers shall be used (unless approved by Carboline).
PACKAGING
Remove oil, grease or other loose or foreign materials and PLASITE 5306 is offered in the following options (primer and gel
contaminants. kits included):
A good bonding tooth, a texture of 40 to 60 grit sandpaper, is A standard unit consists of:
desired with the removal of all glaze. To provide the foregoing 8 cartons of liquids
bonding tooth, it is necessary to prepare the surface using one of A carton consists of:
(2) cans of Part A
the following methods: sandblast with fine sand and reduced
(2) cans of Part B
pressure, scarify or rotary shot blast such as Blastrac®.
12 bags of PLASITE 5300 Series Aggregate
Old Concrete
Remove all powdery, weak concrete, paint, wax, oil, grease or other
A 1/2 bulk unit consist of:
contaminants.
(1) 55 gallon drum of Part A
(1) 55 gallon drum of Part B
Once the concrete has been cleaned and neutralized, one of the
114 bags of PLASITE 5300 Series Aggregate
following methods shall be used to provide a good bonding tooth, a
15 cartons of measuring tool
surface with a texture of 40 to 60 grit sandpaper, with the removal of
all glaze: sandblast with fine sand and reduced pressure, scarify or A 3/4 bulk unit consist of:
rotary shot blast such as Blastrac®. (1) 55 gallon drum of Part A
(1) 55 gallon drum of Part B
Note: Degree of contamination and intended service will deter- 171 bags of PLASITE 5300 Series Aggregate
mine degree of surface preparation. All surfaces must be dry 15 cartons of measuring tool
before application.
A bulk unit consist of:
(1) 55 gallon drum of Part A
Metal Surfaces
(1) 55 gallon drum of Part B
Degrease surface prior to sandblasting. Use organic solvents,
228 bags of PLASITE 5300 Series Aggregate
alkaline solutions, steam, hot water with detergents or other
15 cartons of measuring tool
systems that will completely remove dirt, oil, grease, etc.
COVERAGE
Blast the surface to near white SSPC-SP10 or NACE No. 2 using a
Coverage based on a normal surface at 1/8in./3mm.
Venturi blast nozzle with 100 psi air. To produce the 4 mil/0.1 mm
A standard unit will cover 132 sq.ft/1/8 in/12.3 sq.m
minimum anchor pattern or “tooth,� the blasting media used shall be
A 1/2 bulk unit will cover 1250 sq.ft/116.2 sq.m
a properly graded, clean, sharp angular abrasive similar to Humble
A 3/4 unit will cover 1875 sq.ft/174.3 sq.m
Abrasive Flint S7 (6-30 mesh), Steel Grit (HG25) or BLACK
A bulk unit will cover 2500 sq. ft/232.4 sq.m
BEAUTY® (BB1040).
August 2006 replaces August 2003
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Plasite® are
registered trademarks of Carboline Company.
PLASITE®5306
Polyamine Cured Epoxy Lining
EDGES
If it is necessary to stop when applying PLASITE 5306 liner, do not
MIXING feather the liner out, use the edge of your trowel to cut a sharp (90°)
The primer, liner and gel coat Part A’s are the same material and edge. When work is resumed, simply prime the edge as you prime
are packaged with equal quantity. The same is true for the Part substrate.
B’s.
CURE TIME
Primer Hardening Time: 8 Hours at 70°F/21°C
Mix Part A & B thoroughly (the pot life or working life is
approximately 20 minutes in the can). Curing Time: 72 Hours at 70°F/21°C
Mixer Temperature schedule listed below may be used as a guide when
A mechanical mixer designed for quick, thorough mixing of rapid curing is necessary.
aggregated epoxy coatings similar to those manufactured by:
CLEAN UP
KOL MIXAL Div. of Man U Fab, Inc.
Cured or hardened PLASITE 5306 is almost impossible to remove.
Minneapolis, MN
Clean tools immediately with hot, soapy water or PLASITE Thinner
#71.
KENRICH PRODUCTS
Portland, OR
STORAGE TEMPERATURE
PLASITE 5306 should not be stored at temperatures below 25°F/-4°C
IMPORTANT! The pot life or working life of the liner blend is 30
minutes. Always pour mixed batches as soon as blended. or higher than 85°F/29°C for long periods of time. Storage life is 12
months at 70°F/21°C.
Liner
Empty the contents of Part B into Part A and mix thoroughly. Then Prior to application, all three components and equipment must be
empty the mixture into a mixer, draining the can for about 1/2 minute. stored at 70-85°F/21-29°C for at least 48 hours.
Start mixer and slowly add Part C and mix approximately 5 minutes.
INSPECTION
Note: Person mixing should wear a dust mask or respirator. A pinhole-free film is essential for immersion service. Testing with a
Tinker & Rasor Model AP-W, Stearns Model 14/20 or equivalent is
Gel Coat required. 10,000 to 14,000 volts should be used. Allow a minimum of
Mix Parts A & B thoroughly (the pot life or working life is 48 hours at 70°F/21°C before holiday testing.
approximately 20 minutes in the can).
SAFETY
IMPORTANT! Mixed materials remaining in container will pro-
READ THIS NOTICE
duce heat and may smoke. Keep away from combustible ma-
SAFETY AND MISCELLANEOUS EQUIPMENT
terials. Do not reseal containers!
It is recommended that the operator provide himself with clean
APPLICATION
coveralls and rubber soled shoes and observe good personal
Application in direct sunlight and rising surface temperatures may
hygiene. Certain personnel may be sensitive to various types of
result in blistering of the materials due to expansion of entrapped air
resins which may cause dermatitis.
or moisture in the concrete.
FIRE AND EXPLOSION HAZARDS: PRODUCT CONTAINS LESS
Concrete surfaces that have been in direct sunlight must be shaded
THAN 1% VOLATILE COMPONENTS. HOWEVER, VAPORS ARE
for 24 hours prior to application and remain shaded until the initial set
HEAVIER THAN AIR AND COULD TRAVEL LONG DISTANCES,
has taken place. When the surface temperatures are rising, it may be
IGNITE, AND FLASHBACK. ELIMINATE ALL IGNITION
necessary to postpone the application or apply during the cooler
SOURCES. Keep away from heat, sparks and open flame and use
evening hours.
necessary safety equipment, such as, air mask, explosion-proof
electrical equipment, non-sparking tool and ladders, etc. Avoid
Primer
contact with skin and breathing of vapor or spray mist. When working
Apply by brush or roller. Apply as thin a film as possible to wet the
in tanks, rooms and other enclosed spaces, adequate ventilation
surface. Excessive primer application may cause liner to sag.
must be provided and respirators or fresh air supplied hoods may be
required. Refer to PLASITE Bulletin PA-3. Keep out of the reach of
Note: If primer hardens prior to liner application, the surface
children.
must be whip blasted again before applying liner.
CAUTION - Read and follow all caution statements on this product
Liner
data sheet, material safety data sheet and container label for this
Spread liner evenly over surface. Build up low spots to desired
product.
thickness. Finish each batch as you go. A 3 1/2� X 10� trowel with
rounded corners (referred to as a swimming pool trowel) is
recommended for liner application.
Gel Coat
A gel coat is recommended to provide maximum chemical resistance.
The gel coat may be applied by brush or roller once the liner has
hardened enough to allow application without damaging the liner.
Make sure all pores or trowel pulls are completely sealed keeping as
thin a film as possible.
August 2006 replaces August 2003
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Plasite® are
registered trademarks of Carboline Company.
|