Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: msds_carboline_com---plasite7208pds2-04.asp
                                                                                                                                           PLASITE庐 7208


TYPE
PHYSICAL SPECIFICATIONS
A self-priming epoxy cured with an amine curing agent and
formulated with special pigmentation to produce a cured film
Solids:鈥?.鈥?71% 卤 2% by weight; 52% 卤 2% by volume
having a degree of electrical conductivity.
Pot Life:鈥︹?︹?︹?︹??..鈥pproximately 24 hours at 70掳F
INTENDED USE
A chemically resistant protective coating which will effectively Shelf Life: 24 months minimum at 70掳F. Material in
bleed off accumulated electrostatic charge. Note: Plasite stock should be turned upside down every 3 to 6
7208 is not to be used for immersion service. FOR
months.
INDUSTRIAL USE ONLY!
Shipping Weight:鈥?..鈥︹?︹?︹??..Approx. 11.3 lbs/gallon
CHEMICAL RESISTANCE
Electrical Resistance:鈥?.<25,000 ohm point-to-
Excellent resistance to a wide range of chemical fumes and
spillage. ground. It is understood user must determine suitability
for his specific use. (Please also refer to NOTE
APPLICATION pertaining to PRIMERS.)
Formulated for standard production type spray equipment.
For interior process areas where structural steel, floors,
COLORS equipment, ducts and other surfaces are subject to attack by
Smoky White, Sky, Sea Breeze, Sand, Oyster strong fumes, occasional spills and splash, a near white blast
(SSPC-SP10) would be recommended.
FILM THICKNESS
A 1 陆 to 3 mil coat is produced in one multi-pass spray coat. Where mild corrosive areas and atmospheric conditions exist,
a commercial blast (SSPC-SP6) would be suggested as
Note: Exceeding a 4 mil DFT may result in the loss of a portion
surface preparation.
or all of the electrical conductivity properties of this coating.

Anchor pattern should correspond to approximately 25% of
COVERAGE
the total film thickness of the coating film being applied.
2
786 mil ft /gallon 卤 2% (theoretical). For estimating purposes,
2
157 ft /gallon will produce a 4 mil film (20% loss included).
Concrete
Fully cured concrete must be blasted or acid etched to
DRYING TIME
provide a hard, firm, clean and neutral surface for coating.
Surface will normally be tack free in 2 to 3 hours at 70掳F.
Note: Although concrete may be somewhat conductive, it is
CURING TIME recommended that a prime coat of Plasite 7240 be applied prior
5 days at 90掳F; 7 days at 70掳F. Consult Carboline Technical to the application of Plasite 7208.
Service Department for force curing information.
Aluminum
VOC CONTENT Surface shall be clean and grease free with a blast produced
anchor pattern or 鈥渢ooth鈥? as described earlier under STEEL.
Coating as Supplied Thinned 10% by Volume In addition, the blasted surface shall be given a chemical
(ASTM Method D2369) with PLASITE Thinner #71
treatment such as:
Color Lbs./Gal. g/L *Lbs./Gal. *g/L
ALODINE 1200S available from
Smoky
3.17 卤 2% 3.50 卤 2% Henkel Surface Technologies
419 卤 2%
380 卤 2%
White
32100 Stephenson Highway
*Determined theoretically by using ASTM Method test results
Madison Heights, MI 48071
Note: VOC content may vary between colors. Contact
Carboline Technical Service Department for VOC of specific
IRIDITE 14-2 produced by
colors.
MacDermid Incorporated
245 Freight Street
THINNERS
Waterbury, CT 06702
Plasite Thinner #71 recommended. Normal application
temperature and conditions will require the addition of 10%
OAKITE CRYSCOAT 747LTS
thinner by volume.
and
OAKITE CRYSCOAT ULTRASEAL
SURFACE PREPARATION
Produced by Oakite Products
Steel
50 Valley Road
Prepare surfaces by blasting to degree dictated by service
Berkeley Heights, NJ 07922
conditions.
February 2004 279P
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline庐 and Plasite庐 are
registered trademarks of Carboline Company.
PLASITE庐7208
Note: All welds, pits and rough metal areas should be coated by
If unable to blast light gauge aluminum, consult the Carboline
brush prior to spray application.
Technical Service Department.

Wood, Transite and Similar Surfaces
SAFETY
Normally these materials need no surface treatment provided
READ THIS NOTICE
they are free of grease, oil and dirt. It is generally
SAFETY AND MISCELLANEOUS EQUIPMENT
recommended that a sealer coat of Plasite 7240 be applied
prior to the application of Plasite 7208. Consult Carboline
For tank lining work or enclosed spaces, it is
Technical Service Department for further information.
recommended that the operator provide himself with
clean coveralls and rubber soled shoes and observe
EQUIPMENT
good personal hygiene. Certain personnel may be
Spray Application
sensitive to various types of resins which may cause
All spray equipment shall be thoroughly cleaned and the hose,
in particular, should be free of old paint film and other dermatitis.
contaminants.
THE SOLVENT IN THIS COATING IS FLAMMABLE
AND CARE AS DEMANDED BY GOOD PRACTICE,
Use standard production-type spray guns:
OSHA, STATE AND LOCAL SAFETY CODES, ETC.
GUN FLUID AIR
MUST BE FOLLOWED CLOSELY. Keep away from
DeVilbiss JGA-503 E 797
heat, sparks and open flame and use necessary safety
Binks #18 66-SS 63-PB
equipment, such as, air mask, explosion-proof
Graco P-800 04 02
electrical equipment, non-sparking tools and ladders,
When airless spray equipment is used, the recommended
etc. Avoid contact with skin and breathing of vapor or
liquid pressure is 1500-1800 psi, with tip size from .015 to
spray mist. When working in tanks, rooms and other
.021鈥?. Thinning requirements are more than for conventional
enclosed spaces, adequate ventilation must be
spray.
provided. Refer to PLASITE Bulletin PA-3. Keep out
MIXING of the reach of children.
The curing agent is in a separate container and measured for
CAUTION - Read and follow all caution statements on
the coating unit supplied. Thoroughly mix the pigments. After
this product data sheet, material safety data sheet and
the pigment and liquid are thoroughly mixed, add the
measured liquid curing agent slowly and mix completely with container label for this product.
the coating. The coating should stand approximately 30
minutes after the curing agent has been thoroughly mixed.
This data sheet provides standard information on the coating
APPLICATION PROCEDURE and application procedure. Since varying con-ditions may not
1. Air supply shall be uncontaminated. Adjust air pressure to be covered, consult with your local sales representative or
approximately 50 lbs. at the gun and provide 5 to 10 lbs. of pot Carboline Technical Service Department for further
pressure. Adjust spray gun by first opening liquid valve and information.
then adjusting air valve to give an 8 to 12鈥? spray pattern with
best possible atomization.

2. Apply a 鈥渕ist鈥? bonding pass.

3. Allow to dry approximately one minute but not long enough
to allow film to completely dry.

4. Apply crisscross multi-passes, moving gun at fairly rapid rate
maintaining a wet appearing film. Fast multi-passes may be
applied until you have a film thickness of approximately 5 to 6
mils (approximately 10 to 12 wet mils).

5. Overcoat time will vary both with temperature and ventilation
and will normally require 10 to 12 hours at 70掳F for enclosed
spaces. Less time is required for exteriors. Remove all
overspray by dry brushing or scraping if required.

6. By repeating Step 4, a homogeneous film of 12 to 15 mils is
obtained.

7. Equipment must be thoroughly cleaned immediately after
use with Plasite thinner to prevent the hardening of the primer
in the equipment.


February 2004
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline庐 and Plasite庐 are
registered trademarks of Carboline Company.

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
msds_carboline_com---phenoline302pds8-05.asp N/A
msds_carboline_com---phenoline311pds9-07.asp N/A
msds_carboline_com---phenoline333pds6-07.asp N/A
msds_carboline_com---phenoline341pds1-08.asp N/A
msds_carboline_com---phenoline379pds4-03.asp N/A
msds_carboline_com---plasite3066pds8-07.asp N/A
msds_carboline_com---plasite3070pds8-03.asp N/A
msds_carboline_com---plasite4007&4007cipds5-05.asp N/A
msds_carboline_com---plasite4100pds1-06.asp N/A
msds_carboline_com---plasite4300pds1-06.asp N/A
msds_carboline_com---plasite4310pds1-06.asp N/A
msds_carboline_com---plasite4500spds5-07.asp N/A
msds_carboline_com---plasite4550pds9-07.asp N/A
msds_carboline_com---plasite4550spds6-06-marine.asp N/A
msds_carboline_com---plasite4555spds5-05-marine.asp N/A
msds_carboline_com---plasite4555spds5-05.asp N/A
msds_carboline_com---plasite4600pds8-03.asp N/A
msds_carboline_com---plasite4600pds8-06-marine.asp N/A
msds_carboline_com---plasite5302arpds5-04.asp N/A
msds_carboline_com---plasite5306pds8-06.asp N/A
msds_carboline_com---plasite5309pds8-03.asp N/A
msds_carboline_com---plasite7102pds2-04.asp N/A
msds_carboline_com---plasite7111pds8-03.asp N/A
msds_carboline_com---plasite7122hspds6-05.asp N/A
msds_carboline_com---plasite7122lpds10-07.asp N/A
msds_carboline_com---plasite7122pds8-06-marine.asp N/A
msds_carboline_com---plasite7133hspds11-04.asp N/A
msds_carboline_com---plasite7159pds1-07.asp N/A
msds_carboline_com---plasite7208pds2-04.asp N/A
msds_carboline_com---plasite797pds3-04.asp N/A
msds_carboline_com---plasite9053pds8-05.asp N/A
msds_carboline_com---plasite9057pds8-03-marine.asp N/A
msds_carboline_com---plasite9060pds8-06-marine.asp N/A
msds_carboline_com---plasite9060pds9-06.asp N/A
msds_carboline_com---plasite9081pds8-03.asp N/A
msds_carboline_com---plasite9085pds8-03.asp N/A
msds_carboline_com---plasite9122pds8-03.asp N/A
msds_carboline_com---plasite9133pds11-07.asp N/A
msds_carboline_com---plasite9145pds8-03.asp N/A
msds_carboline_com---plasite9200harpds2-04.asp N/A
msds_carboline_com---plasite943pds2-04.asp N/A
msds_carboline_com---plasite9500pds7-05.asp N/A
msds_carboline_com---plasite9570&har&tfepds7-08.asp N/A
msds_carboline_com---plasite9571pds10-06.asp N/A
msds_carboline_com---plasite9573pds8-03.asp N/A
msds_carboline_com---polyclad708pds8-07.asp N/A
msds_carboline_com---pyrocote1340pds10-06.asp N/A
msds_carboline_com---pyrocrete239ai7-04.asp N/A
msds_carboline_com---pyrocrete239pds1-06.asp N/A
msds_carboline_com---pyrocrete40pds7-04.asp N/A

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC