Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: msds_carboline_com---plasite797pds3-04.asp
                                                                                                                                                PLASITE庐 797
100% Epoxy Floor Coating
Formerly PLASGUARD 797




TYPE
PHYSICAL SPECIFICATIONS
A glass filled two-part epoxy polyamine 100% solids
flooring. Pigments: Titanium dioxide, iron oxide black, glass
and inerts.
INTENDED USE
Primarily as a chemical resistant, 100% solids, high Solids: 100% by weight; 100% by volume
gloss coating for areas where a tough, abrasion
Pot Life (at 70掳F): Unthinned: 100% volume solids 鈥?
resistant, color stable, easy-to-clean flooring is
45 minutes. Thinned: 95% volume solids 鈥? 1 hour.
required. When used with a #30 mesh silica sand will
Shelf Life: 12 months at 70掳F.
produce a tough skid resistant surface with a
thickness of 1/16鈥?. FOR INDUSTRIAL USE ONLY! Shipping Weight: Approximately 14 lbs. per 1 gallon
kit.
COLORS
Thermal Shock: Unaffected 5 cycles, minus 70掳F to
Gray, Tile Red, White, Green & Tan
plus 200掳F.
FILM THICKNESS
Mixing Ratio: 2 to 1 by volume
10 to 20 mils DFT
Gloss: 85 to 95 at 60掳
Horizontal Surfaces 鈥? Spray: 10 to 14 mils can be
CHEMICAL RESISTANCE
applied in one multi-pass spray coat.
Horizontal Surfaces 鈥? Brush or Roller: 10 to 14 mils
Plasite 797 has good overall chemical resistance to a
DFT can be applied in one coat.
wide range of chemicals. Refer to Carboline Technical
Service Department for specific recommendations.
COVERAGE
1604 mil ft.2/gal. (theoretical). For estimating Brush or Roller
purposes, 90 ft.2/gal. will produce a 16 mil film (10% If desired, material may be thinned up to 5% by
loss included). volume.
TACK-FREE TIME (at 70掳F) SURFACE PREPARATION
Surface will normally be tack-free in 5 hours at 70掳F Steel
(unthinned 鈥? 100% volume solids). Depending on severity of intended coating use, SSPC-
SP 10 near white blast preferred to SSPC-SP 6
If thinner is added, tack-free time will increase.
commercial blast. An anchor pattern or 鈥渢ooth鈥? in the
metal shall correspond to approximately 20 to 25% of
DRYING TIME (foot traffic acceptable)
the total film thickness of the coating.
10 hours at 90掳F; 14 hours at 70掳F; 20 hours at 50掳F.
Concrete
CURING TIME
Concrete must be fully cured (28 days minimum) and
3 days at 90掳F; 5 days at 70掳F; 7 days at 50掳F.
properly cleaned and prepared by either whip blasting
or acid etch (properly neutralized).
OVERCOATING TIME
Minimum: Can be topcoated when previously applied
APPLICATION
coating is tack-free. Refer to TACK-FREE TIME.
All spray equipment should be thoroughly cleaned
and the hose, in particular, should be free of old paint
Maximum (at 70掳F): 7 days; or 72 hours if exposed to
film and other contaminants.
UV light.
Use standard production type spray guns:
THINNERS
GUN FLUID AIR
Plasite Thinner #71 is recommended.
DeVilbiss JGA-510 E 797
Binks #2001 66-SS 63-PB
Spray
Graco P800 04 02
Depending on type of spray equipment used, it may
be necessary to add thinner. Amount of thinner will When airless spray equipment is used, the
vary with equipment capabilities, temperature and recommended liquid pressure is 1500 to 2200 psi with a
conditions. tip size from .015鈥? to .021鈥?.
March 2004 243P
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline庐 and Plasite庐 are
registered trademarks of Carboline Company.
PLASITE庐797
Back roll to release any entrapped air.
Mixing
Plasite 797 is supplied in one or five gallon containers.
Brush
The curing agent and coating are supplied in separate
Using a good quality brush, apply a flow coat of
containers at a 2:1 ratio. For splitting purposes, use on
approximately 10 to 14 mils.
part curing agent to two parts coating by volume.
Thoroughly mix both Part I and Part II in their separate
Equipment must be thoroughly cleaned immediately
containers. Then combine parts at a 2:1 ratio. While
after use with Plasite Thinner #71.
mixing Part I and Part II, scrape sides and bottom of
container to ensure that all of the coating is thoroughly INSPECTION
mixed. The addition of 5% thinner may be added to Degree of surface preparation and film thickness shall
extend the pot life. conform to appropriate specification as outlined in
SURFACE PREPARATION AND FILM THICKNESS
Note: If Part I and Part II are not thoroughly mixed, soft spots
sections.
may occur on the floor.

Refer to Plasite Bulletin PA-3 for inspection
Note: Mix only that amount which can be safely used within the pot
life of the material. Refer to Pot Life. requirements.

Thoroughly clean and dry substrate prior to application. SAFETY
Large surface irregularities or trash particles may READ THIS NOTICE
telegraph through the coating finish. SAFETY & MISCELLANEOUS EQUIPMENT
When applying material over a porous substrate, the For tank lining work or enclosed spaces, it is
use of two or more coats is recommended. The first recommended that the operator provide himself with
coat is to fill voids and seal porosities. clean coveralls and rubber soled shoes and observe
good personal hygiene. Certain personnel may be
First Coat Application sensitive to various types of resins which may cause
To seal the porosities in the substrate, thin the material dermatitis.
approximately 10 to 15% (depending on porosity) and
apply at a thickness of 4 to 8 mils. WHEN ADDED, THE THINNER USED IN THIS
COATING IS FLAMMABLE AND CARE AS
Immediately back roll with a spike roller to release any DEMANDED BY GOOD PRACTICE, OSHA, STATE
entrapped air. AND LOCAL SAFETY CODES, ETC. MUST BE
FOLLOWED CLOSELY. Keep away from heat, sparks
Note: Although this coat may be spray applied, best results will
and open flame and use necessary safety equipment,
be obtained by brush or roller application.
such as, air mask, explosion-proof electrical equipment,
non-sparking tools and ladders, etc. Avoid contact with
Overcoating Time: Minimum 鈥? can be topcoated when
skin and breathing of vapor or spray mist. When
previous coat is tack-free. Maximum 鈥? 7 days.
working in tanks, rooms and other enclosed spaces,
Lightly sand or remove any high spots and thoroughly adequate ventilation must be provided. Refer to
clean. PLASITE Bulletin PA-3. Keep out of the reach of
children.
Second Coat Application
CAUTION - Read and follow all caution statements on
Spray
this product data sheet, material safety data sheet and
Thin material approximately 5% with Plasite Thinner
container label for this product.
#71.

Using a crisscross multi-pass method, apply This product data sheet provides standard information
approximately 10 to 14 mils. on the coating and application procedure. Since varying
conditions may not be covered, consult with your local
Back roll with a spike roller. sales representative or Carboline Technical Service
Department for further information.
Roller
Pour material in a ribbon on the floor and distribute
evenly (use of a notched squeegee or screed board
may provide better distribution of material).

Using a 3/16鈥? mohair roller, roll material to a film
thickness of approximately 10 to 14 mils.


March 2004
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline庐 and Plasite庐 are
registered trademarks of Carboline Company.

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
msds_carboline_com---phenoline302pds8-05.asp N/A
msds_carboline_com---phenoline311pds9-07.asp N/A
msds_carboline_com---phenoline333pds6-07.asp N/A
msds_carboline_com---phenoline341pds1-08.asp N/A
msds_carboline_com---phenoline379pds4-03.asp N/A
msds_carboline_com---plasite3066pds8-07.asp N/A
msds_carboline_com---plasite3070pds8-03.asp N/A
msds_carboline_com---plasite4007&4007cipds5-05.asp N/A
msds_carboline_com---plasite4100pds1-06.asp N/A
msds_carboline_com---plasite4300pds1-06.asp N/A
msds_carboline_com---plasite4310pds1-06.asp N/A
msds_carboline_com---plasite4500spds5-07.asp N/A
msds_carboline_com---plasite4550pds9-07.asp N/A
msds_carboline_com---plasite4550spds6-06-marine.asp N/A
msds_carboline_com---plasite4555spds5-05-marine.asp N/A
msds_carboline_com---plasite4555spds5-05.asp N/A
msds_carboline_com---plasite4600pds8-03.asp N/A
msds_carboline_com---plasite4600pds8-06-marine.asp N/A
msds_carboline_com---plasite5302arpds5-04.asp N/A
msds_carboline_com---plasite5306pds8-06.asp N/A
msds_carboline_com---plasite5309pds8-03.asp N/A
msds_carboline_com---plasite7102pds2-04.asp N/A
msds_carboline_com---plasite7111pds8-03.asp N/A
msds_carboline_com---plasite7122hspds6-05.asp N/A
msds_carboline_com---plasite7122lpds10-07.asp N/A
msds_carboline_com---plasite7122pds8-06-marine.asp N/A
msds_carboline_com---plasite7133hspds11-04.asp N/A
msds_carboline_com---plasite7159pds1-07.asp N/A
msds_carboline_com---plasite7208pds2-04.asp N/A
msds_carboline_com---plasite797pds3-04.asp N/A
msds_carboline_com---plasite9053pds8-05.asp N/A
msds_carboline_com---plasite9057pds8-03-marine.asp N/A
msds_carboline_com---plasite9060pds8-06-marine.asp N/A
msds_carboline_com---plasite9060pds9-06.asp N/A
msds_carboline_com---plasite9081pds8-03.asp N/A
msds_carboline_com---plasite9085pds8-03.asp N/A
msds_carboline_com---plasite9122pds8-03.asp N/A
msds_carboline_com---plasite9133pds11-07.asp N/A
msds_carboline_com---plasite9145pds8-03.asp N/A
msds_carboline_com---plasite9200harpds2-04.asp N/A
msds_carboline_com---plasite943pds2-04.asp N/A
msds_carboline_com---plasite9500pds7-05.asp N/A
msds_carboline_com---plasite9570&har&tfepds7-08.asp N/A
msds_carboline_com---plasite9571pds10-06.asp N/A
msds_carboline_com---plasite9573pds8-03.asp N/A
msds_carboline_com---polyclad708pds8-07.asp N/A
msds_carboline_com---pyrocote1340pds10-06.asp N/A
msds_carboline_com---pyrocrete239ai7-04.asp N/A
msds_carboline_com---pyrocrete239pds1-06.asp N/A
msds_carboline_com---pyrocrete40pds7-04.asp N/A

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC