Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: msds_carboline_com---plasite9133pds11-07.asp
                                                                                                                                              PLASITE® 9133


PHYSICAL CHARACTERISTICS
PRODUCT DESCRIPTION
A high solid epoxy cured with a polyamine-type curing agent, formulated
with a wide range of chemical resistance and ease of handling. *Abrasion Resistance:…â??.â€?...94.22 mg (ASTM D-4060,CS-17 Wheels)
*Surface Hardness:â€?..…â?¦â?¦â?¦â?¦â?¦â?¦â??.84 seconds (ASTM D4366-84)
USES/APPLICATIONS
Food grade cargos Solids:…â?¦â??...…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??.…â?¦â?¦â?¦â?¦â??.Weight: 92.9% ± 2%
Aqueous food Volume: 85.6% ± 2%
Railcars
Pot Life:…â?¦â?¦â?¦â?¦â?¦â?¦â??.…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??70°F/21°C: 2 hours
APPROVAL /CERTIFICATIONS Shelf Life:…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??.24 months @70°F/21°C
PLASITE 9133 meets the FDA requirements for 21CFR 175.300 Shipping Weight:…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??..15 lbs./gal.
for aqueous food contact.

Thermal Shock: Unaffected 5 cycles minus
TEMPERATURE RESISTANCE
Dry film basis is 300°F/149°C for short periods. Continuous immersion 70°F/-56°C to plus 200°F/93°C
temperatures depend on particular reagent.
Gloss:…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??.…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??...â€?.58 @ 60°
CHEMICAL RESISTANCE *Note: Above tests were conducted on film cured at 150°F/66°C.
Excellent resistance to a wide range of chemicals and aqueous food
solutions. PLASITE Thinner #69 - A special blend of fast evaporating solvents
containing no aromatic hydrocarbons.
STANDARD COLORS
Light gray, White and Light Blue. It will always be necessary to thin the coating. The applicator must make
exact thinner adjustments based on his equipment, air and surface
temperatures. The following thinning guidelines are approximate.
PACKAGING
Normal application temperatures and conditions will require the addition
PLASITE 9133 is available in one and five gallon kits that include the
of approximately 5-15% thinner by volume with approximately 5%
following:
additional thinner added for each 5°F/3°C of increased temperature. It is
recommended that the amount of thinner included on each order amount
One gallon kit includes:
to approximately 20% of the coating order.
1 1 gallon can of Part A
1 1 gallon can of Part B
CLEANUP THINNER: Thinner #71
Five gallon kit includes:
VOC CONTENT
1 5 gallon bucket of Part A
1 3 gallon bucket of Part B
Thinned 20% by Volume with
Coating as Supplied
FILM THICKNESS PLASITE Thinner #71 or #69
(Determined Theoretically)
A 4-6 mil/100-150 microns film is produced in one multi-pass spray coat. (Determined Theoretically)
A two coat application of 8-12 mil/200-300 microns is recommended film
Color Lbs./Gal. g/L Lbs./Gal. g/L
thickness when used as a lining for immersion services. Some services
White 1.00 ± 2% 119 ± 2% 1.96 ± 2% 235 ± 2%
may require 12-15 mil/300-375 microns.

COVERAGE SUBSTRATE PREPARATION
One gallon of PLASITE 9133 will cover approximately 1,373 sq. ft./gal. Steel
For estimating purposes, 122 sq. ft./gal. will produce a 9 mil/225 microns High Temperature & Immersion Service
film (20% loss included). Two coats will produce an 8-12 mil/200-300 All sharp edges shall be ground to produce a radius and all imperfections
microns film for immersion service. such as skip welds, delaminations, scabs, slivers and slag shall be
corrected prior to abrasive blasting. Skip welds shall be welded solid.
STORAGE CONDITIONS
Keep PLASITE 9133 products tightly sealed in their original containers Degrease surface prior to sandblasting. Organic solvents, alkaline
until ready for use. Store at 50-85°F/10-29°C and out of direct sunlight. solutions, steam, hot water with detergents or other systems that will
PLASITE 9133 has a shelf life of two years from the manufacture date. completely remove dirt, oil, grease, etc. may be used. Used tanks may
require additional decontamination.
Proper jobsite storage of PLASITE 9133 is essential to its performance.
Follow these general procedures for storage at the jobsite: The surface shall be blasted to a minimum SSPC-SP10 or NACE No. 2
Store components (Part A and Part B) unopened, in a dry place, at 50- near white metal surface using a Venturi blast nozzle supplied with 80-100
85°F/10-29°C, out of direct sunlight, and protected from the elements. psi. An anchor pattern or “tooth� in the metal shall correspond to
Keep away from heat and flame. approximately 20 to 25% of the total film thickness of the coating.
For the 24-48 hours just prior to use, narrow the storage temperature to Note: Contaminated grit shall not be used for the finish work.
70-85°F/21-29°C to facilitate ease of mixing.
The blasting media used shall be a natural abrasive, steel grit, or slag grit
THINNERS (similar or equal to BLACK BEAUTY®). These abrasives shall be sharp
PLASITE Thinner #71 - A medium fast thinner to be used under most with a hard-cutting surface, properly graded, dry and of best quality. The
conditions. media shall be of proper size to obtain the specified anchor pattern and
shall be free of objectionable contaminants.
The anchor pattern shall be sharp and no evidence of a polished surface
is allowed.


163P
November 2007 replaces January 2004
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Plasite® are
Page 1 of 4
registered trademarks of Carboline Company.
PLASITE®9133
by volume. Thoroughly mix resin, then add curing agent slowly and mix
completely with resin. The coating should stand approximately 15 minutes
Remove all traces of grit and dust with a vacuum cleaner or by brushing. after the curing agent has been thoroughly mixed.
Care must be taken to avoid contaminating the surface with fingerprints or
from detrimental material on the workers� clothes. Spray
All spray equipment should be thoroughly cleaned and the hose, in
The surface temperature shall be maintained at a minimum of 5°F/3°C particular, should be free of old paint film and other contaminants.
above the dew point to prevent oxidation of the surface. The coating shall Use standard production type spray guns:
be applied within the same day that the surface has been prepared.
GUN FLUID AIR
Visible oxidation or condensation is not allowed.
DeVilbiss JGA-510 E 797
Binks #2001 66-SS 63-PB
Service in Corrosive Atmosphere
Graco P800 04 02
Degrease as described above.

When airless spray equipment is used, the recommended liquid pressure is
SSPC-SP10 or NACE No. 2 (near white metal blast cleaning) - strong
1500-1800 psi with tip size from .017-.021 inches. Thinning requirements
fumes and splash spill.
are more than for conventional spray.
SSPC-SP6 or NACE No. 3 (commercial blast cleaning) - high temperature
Air supply shall be uncontaminated. Adjust air pressure to approximately 50
fumes.
psi at the gun and provide 5-10 lbs. of pot pressure. Adjust spray gun by
first opening liquid valve and then adjusting air valve to give an 8-12 inch
SSPC-SP7 or NACE No. 4 (brush-off blast cleaning) - chemical
wide spray pattern with best possible atomization.
atmosphere and weathering.

SSPC-SP3 (power tool cleaning) - chemical atmosphere and weathering. Apply a “mist� bonding pass.

When utilized, inhibitive primer should be applied as soon as possible Allow to dry approximately one minute but not long enough to allow film to
after surface preparation. completely dry.

Surface preparation for chemical atmosphere and weathering must result Apply crisscross multi-passes, moving gun at fairly rapid rate, maintaining a
in a relatively rough surface. If the steel is new and this type of surface wet appearing film. Fast multi-passes may be applied until you have a film
preparation does not leave a reasonably rough surface on the steel, then thickness of approximately 4-6 mil/100-150 microns (approximately 5-7 wet
the heavy film system is not recommended. mil/125-175 microns). Repeat this procedure for the second coat to obtain
an 8-12 mil/200-300 microns DFT.
Depending on service conditions, film thickness requirements may be
reduced. Contact Carboline Technical Service Department for further Overcoat time will vary both with temperature and ventilation and will
information. require from 10-12 hours at 70°F/21°C for enclosed spaces. Less time is
required for exteriors. Remove all overspray by dry brushing or scraping if
Concrete required.
Contact Carboline’s Technical Service for a recommendation.
Equipment must be thoroughly cleaned immediately after use with a
Galvanized Steel PLASITE thinner to prevent the setting of the coating.
Contact Carboline’s Technical Service for a recommendation.
Note: Prior to spray application, stripe brush all weld attachments and
Aluminum surface irregularities using PLASITE 9133 thinned a minimum of 50%
Surface shall be clean and grease-free with a blast produced anchor by volume with PLASITE Thinner #71.
pattern or “tooth� as described earlier under STEEL. In addition, the
blasted surface shall be given a chemical treatment such as: Brush
Recommended for small areas and repairs only. Use a high quality brush,
ALODINE 1200S available from Henkel Surface Tech and apply a very light crisscross brush coat. Allow to dry for approximately
5 minutes. Then apply a heavy coat using a crisscross brush pattern. “Flow�
IRIDITE 14-2 produced by MacDermid Incorporated
the coating on rather than try to “brush out.� Allow to dry tack-free. Repeat
OAKITE CRYSCOAT 747LTS and OAKITE CRYSCOAT ULTRASEAL until sufficient film thickness is obtained. Normally, a film thickness of 2.5-3
mil (62-75 microns) can be obtained per coat by this method.
produced by Oakite Products
For immersion, blasting with sharp grit followed by the chemical surface CURING
treatment is required. Surface will normally be tack-free in 8-10 hours at 70°F/21°C.
Note: On metallic surfaces prepared only by chemical etching, the For general immersion service requirements, curing will normally take place
total coating film thickness applied should be restricted to only half the in 5 days at 90°F/32°C, 7 days at 70°F/21°C or 14 days at 50°F/10°C. This
film normally applied to blasted surfaces. This reduced film thickness coating should not be applied when air temperature or temperature of
should be considered during selection of the coating for the service
surface to be coated is below 50°F/10°C.
and the type of surface preparation performed.
Where coating is to be subject to immersion in aqueous food, it is required
APPLICATION GUIDELINES that the final cure be 225°F/107°C (metal temperature) for four hours
Before mixing and applying any material, make sure environmental
minimum.
conditions are satisfactory for application. Weather conditions, and
especially dew point, should be constantly monitored in light of the work
Listed below are a few curing schedules that may be used for time and
being done. Final blast cleaning and application of the lining system must
work planning. Prior to raising the metal to the force curing temperature, it is
only be performed when it is clear the temperature of the steel substrate
necessary that an air dry time of 2-5 hours at temperatures from 70-
will not fall within 5°F/3°C of the dew point. Dehumidification and/or 100°F/21-38°C be allowed. After the air dry period has elapsed, the
temperature control may be necessary to meet this requirement. Use a
temperature should be raised by approximately 30°F/17°C each 30 minutes
surface thermometer to frequently monitor the temperature of the steel
until the desired force curing temperatures are reached.
substrate.
METAL CURING
TEMPERATURE TIME
Mixing
12 Hrs
150°F/66°C
The curing agent and resin are supplied in separate containers at a 2:1
10 Hrs
ratio. For splitting purposes, use one part curing agent to two parts resin 175°F/79°C
6 Hrs
200°F/93°C
4 Hrs
225°F/107°C

November 2007 replaces January 2004
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Plasite® are
registered trademarks of Carboline Company.
PLASITE® 9133
Final cure may be checked by exposing coated surface to MIBK for 10
SAFETY
minutes. If no dissolving and only minor softening of film occurs, the
curing can be considered complete. The film should reharden after READ THIS NOTICE
exposure if cured. SAFETY AND MISCELLANEOUS EQUIPMENT

For tank lining work or enclosed spaces, it is recommended that the
INSPECTION
operator provide himself with clean coveralls and rubber soled shoes and
observe good personal hygiene. Certain personnel may be sensitive to
Refer to Plasite Bulletin PA-3, Section 3, for inspection requirements. various types of resins which may cause dermatitis.
RECOMMENDATIONS THE SOLVENT IN THIS COATING IS FLAMMABLE AND CARE AS
Apply only on a clean, sound, properly prepared substrate. DEMANDED BY GOOD PRACTICE, OSHA, STATE AND LOCAL
SAFETY CODES, ETC. MUST BE FOLLOWED CLOSELY. Keep away
Minimum ambient, material and surface temperatures are
from heat, sparks and open flame and use necessary safety equipment,
50°F/10°C at the time of application.
such as, air mask, explosion-proof electrical equipment, non-sparking
Maximum ambient, material and surface temperatures are
tools and ladders, etc. Avoid contact with skin and breathing of vapor or
110°F/43°C, 90°F/32°C and 125°F/52°C respectively, at the time of
spray mist. When working in tanks, rooms and other enclosed spaces,
application.
adequate ventilation must be provided. Refer to Plasite Bulletin PA-3.
Relative humidity should be between 0-80%. Keep out of the reach of children.
Substrate temperature should be 5°F/3°C above the dew point.
CAUTION - Read and follow all caution statements on this product data
Application and curing times are dependent upon ambient
sheet, material safety data sheet and container label for this product.
conditions. Consult Carboline’s Technical Service Department if
conditions are not within recommended guidelines.

This data sheet provides standard information on the coating and
application procedure. Since varying conditions may not be covered,
PRECAUTIONS consult with your local sales representative or Carboline’s Technical
Service Department for a detailed application and inspection procedure.
PLASITE Thinner #71 or acetone is recommended for clean up of
the PLASITE 9133 material.
Before handling and application of this material consult the MSDS
sheets. As with any product, those handling PLASITE 9133
materials should employ proper safety practice. Hypersensitive
persons should wear protective clothing, gloves, and use protective
cream on any exposed areas.
When PLASITE 9133 is used as a tank lining or in an enclosed
area circulation should be used during and after the installation.
Circulation can be discontinued once the material has cured. The
ventilation equipment should be capable of preventing the solvent
concentration from reaching the lower explosion level for the
solvents used. The applicator should monitor the exposure
levels or use MSHA/NIOSH approved air respirators.

NOTES
Material Safety Data Sheets on PLASITE 9133 are available upon
request.
Specific information regarding the chemical resistance of PLASITE
9133 can be found by contacting Carboline’s Technical Service
Department.
A staff of technical service engineers is available to assist with
product application, or to answer questions related to Carboline
products.
Requests for technical literature or service can be made through
local sales representatives and offices worldwide.




November 2007 replaces January 2004
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Plasite® are
Page 3 of 4
registered trademarks of Carboline Company.

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
msds_carboline_com---phenoline302pds8-05.asp N/A
msds_carboline_com---phenoline311pds9-07.asp N/A
msds_carboline_com---phenoline333pds6-07.asp N/A
msds_carboline_com---phenoline341pds1-08.asp N/A
msds_carboline_com---phenoline379pds4-03.asp N/A
msds_carboline_com---plasite3066pds8-07.asp N/A
msds_carboline_com---plasite3070pds8-03.asp N/A
msds_carboline_com---plasite4007&4007cipds5-05.asp N/A
msds_carboline_com---plasite4100pds1-06.asp N/A
msds_carboline_com---plasite4300pds1-06.asp N/A
msds_carboline_com---plasite4310pds1-06.asp N/A
msds_carboline_com---plasite4500spds5-07.asp N/A
msds_carboline_com---plasite4550pds9-07.asp N/A
msds_carboline_com---plasite4550spds6-06-marine.asp N/A
msds_carboline_com---plasite4555spds5-05-marine.asp N/A
msds_carboline_com---plasite4555spds5-05.asp N/A
msds_carboline_com---plasite4600pds8-03.asp N/A
msds_carboline_com---plasite4600pds8-06-marine.asp N/A
msds_carboline_com---plasite5302arpds5-04.asp N/A
msds_carboline_com---plasite5306pds8-06.asp N/A
msds_carboline_com---plasite5309pds8-03.asp N/A
msds_carboline_com---plasite7102pds2-04.asp N/A
msds_carboline_com---plasite7111pds8-03.asp N/A
msds_carboline_com---plasite7122hspds6-05.asp N/A
msds_carboline_com---plasite7122lpds10-07.asp N/A
msds_carboline_com---plasite7122pds8-06-marine.asp N/A
msds_carboline_com---plasite7133hspds11-04.asp N/A
msds_carboline_com---plasite7159pds1-07.asp N/A
msds_carboline_com---plasite7208pds2-04.asp N/A
msds_carboline_com---plasite797pds3-04.asp N/A
msds_carboline_com---plasite9053pds8-05.asp N/A
msds_carboline_com---plasite9057pds8-03-marine.asp N/A
msds_carboline_com---plasite9060pds8-06-marine.asp N/A
msds_carboline_com---plasite9060pds9-06.asp N/A
msds_carboline_com---plasite9081pds8-03.asp N/A
msds_carboline_com---plasite9085pds8-03.asp N/A
msds_carboline_com---plasite9122pds8-03.asp N/A
msds_carboline_com---plasite9133pds11-07.asp N/A
msds_carboline_com---plasite9145pds8-03.asp N/A
msds_carboline_com---plasite9200harpds2-04.asp N/A
msds_carboline_com---plasite943pds2-04.asp N/A
msds_carboline_com---plasite9500pds7-05.asp N/A
msds_carboline_com---plasite9570&har&tfepds7-08.asp N/A
msds_carboline_com---plasite9571pds10-06.asp N/A
msds_carboline_com---plasite9573pds8-03.asp N/A
msds_carboline_com---polyclad708pds8-07.asp N/A
msds_carboline_com---pyrocote1340pds10-06.asp N/A
msds_carboline_com---pyrocrete239ai7-04.asp N/A
msds_carboline_com---pyrocrete239pds1-06.asp N/A
msds_carboline_com---pyrocrete40pds7-04.asp N/A

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC