PLASITE® 9200 HAR
TYPE
A high solids self-priming epoxy cured with an amine PHYSICAL SPECIFICATIONS
curing agent and formulated with special pigmentation
Solids.…â?¦â?¦â?¦â?¦â?¦â?¦â??.â€?..…â??.93% ± 2% by weight
to produce an abrasion resistant film with a degree of
86% ± 2% by volume
electrical conductivity.
INTENDED USE Pot Life…â?¦â?¦â?¦â?¦â?¦â??.Approximately 4 hours at 70°F
As an internal lining or protective coating on metal,
Shelf Life…â??..24 months minimum at 70°F. Material
concrete, or other conductive surfaces to effectively
in stock should be turned upside down every 3 to 6
bleed off accumulated electrostatic charge. (As
months.
standard concrete filler-sealers having high dielectric
properties cannot be used, Plasite 9200 HAR should
Shipping Weight…â?¦â?¦â?¦â?¦â?¦â??.Approx. 14.2 lbs./gal.
not normally be considered as a total immersion lining
for concrete vessels). FOR INDUSTRIAL USE ONLY!
Gloss…â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â?¦â??...…â??32 at 60°
CHEMICAL RESISTANCE
*Surface Hardness�...Konig Pendulum Hardness of
Excellent resistance to a wide range of chemicals and
155 seconds (Glass Standard = 250 seconds); (ASTM
water solutions.
Method D4366-84)
APPLICATION
*Abrasive Resistance…â??16.1 milligrams average
Formulated for standard production spray equipment.
loss per 1000 cycles. Taber CS-17 Wheel, 1000 gram
weight
COLOR
Medium Gray
Note: Above tests were conducted on film cured at 150°F.
FILM THICKNESS PER COAT
A 6 to 8 mil coat is produced in one multi-pass spray SURFACE PREPARATION
coat. Steel
Surfaces prepared by blasting to degree dictated by
COVERAGE
service conditions. For immersion in severe service, an
1379 mil ft2/gal. ± 2% theoretical. For estimating
SSPC-SP5 or NACE No. 1 white metal with an anchor
purposes, 157 ft2/gal. will produce a 6 to 8 mil film
pattern corresponding to approximately 20 to 25% of
(20% loss included). Two coats will produce a 12 to 15
the total film thickness of the coating film being applied.
mil film for immersion service.
DRYING TIME Concrete
Surface will normally be tack free in 4 to 6 hours at Fully cured concrete must be blasted or acid etched to
70°F. provide a hard, firm, clean and neutral surface for
coating.
CURING TIME
5 days at 90°F; 7 days at 70°F; 10 days at 50°F.
Note: Although concrete may be somewhat conductive, it is
Consult Carboline Technical Service Department for recommended that a prime coat of Plasite 4140 be applied prior
force curing information. to the application of Plasite 9200 HAR.
VOC CONTENT If concrete is to be filled and sealed with Plasite 9028
MI, Plasite 4140 must be used to topcoat the 9028 MI
Thinned 10% by Volume
Coating as Supplied
with PLASITE Thinner #71 prior to the application of Plasite 9200 HAR topcoat.
(Determined Theoretically)
(Determined Theoretically)
For further information contact the Carboline Technical
Service Department.
Color Lbs./Gal. g/L Lbs./Gal. g/L
Medium
0.94 ± 4% 112 ± 4% 1.47 ± 4% 175.5 ± 4%
Gray EQUIPMENT
Spray Application
THINNERS All spray equipment should be thoroughly cleaned
Plasite Thinner #71 is recommended. Normal and the hose, in particular, should be free of old paint
application temperature and conditions will require film and other contaminants.
addition of 10% by volume.
February 2004 291P
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Plasite® are
registered trademarks of Carboline Company.
PLASITE®9200 HAR
Use standard production-type spray guns:
SAFETY
GUN FLUID AIR READ THIS NOTICE
DeVilbiss JGA-510 E 797 SAFETY AND MISCELLANEOUS EQUIPMENT
Binks #18 66-SS 63-PB
Graco P800 04 02
For tank lining work or enclosed spaces, it is
A heavy-duty trigger spring is recommended. Atomizing recommended that the operator provide himself with
air spray is recommended because of the high wear rate clean coveralls and rubber soled shoes and observe
of tips and pump parts on airless spray equipment. good personal hygiene. Certain personnel may be
sensitive to various types of resins which may cause
dermatitis.
MIXING
The curing agent and coating are supplied in separate
containers at a 3:1 ratio. For splitting purposes, use 1 THE SOLVENT IN THIS COATING IS FLAMMABLE
part curing agent to 3 parts coating by volume. AND CARE AS DEMANDED BY GOOD PRACTICE,
Thoroughly mix coating, then add curing agent slowly OSHA, STATE AND LOCAL SAFETY CODES, ETC.
and mix completely with coating. MUST BE FOLLOWED CLOSELY. Keep away from
heat, sparks and open flame and use necessary safety
Note: Continuous mixing during use is required.
equipment, such as, air mask, explosion-proof
electrical equipment, non-sparking tools and ladders,
Note: Nonconductive primers (such as Plasite 7103 Primer)
etc. Avoid contact with skin and breathing of vapor or
should not be used with Plasite 9200 HAR. While it may be
possible to use an electrically conductive primer (such as Plasite spray mist. When working in tanks, rooms and other
1000 inorganic zinc), it is recommended that the Carboline
enclosed spaces, adequate ventilation must be
Technical Service Department be consulted first.
provided. Refer to PLASITE Bulletin PA-3. Keep out
of the reach of children.
APPLICATION PROCEDURE
1. Air supply shall be uncontaminated. Adjust air
CAUTION - Read and follow all caution statements on
pressure to approximately 50 lbs. at the gun and
this product data sheet, material safety data sheet and
provide 5 to 10 lbs. of pot pressure. Adjust spray
container label for this product.
gun by first opening liquid valve and then adjusting
air valve to give an 8� to 12� wide spray pattern with
best possible atomization. Continuous agitation
during use is required.
2. Apply a “mist� bonding pass. This data sheet provides standard information on the
3. Allow to dry approximately one minute, but not long coating and application procedure. Since varying con-
enough to allow film to completely dry. ditions may not be covered, consult with your local sales
4. Apply crisscross multi-passes, moving gun at fairly representative or Carboline Technical Service
rapid rate, maintaining a wet appearing film. Fast Department for further information.
multi-passes may be applied until you have film
thickness of approximately 6 to 7 mils
(approximately 7 to 8 wet mils).
5. Overcoat time will vary both with temperature and
ventilation and will normally require 10 to 12 hours at
70°F for enclosed spaces. Less time is required for
exteriors. Remove all overspray by dry brushing or
scraping if required.
6. By repeating Step No. 4, a homogeneous film of 12
to 15 mils is obtained.
7. Equipment must be thoroughly cleaned immediately
after use with Plasite thinner to prevent the setting of
the coating.
Note: All welds, pits and rough metal areas should be coated by
brush prior to spray application.
February 2004
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline® and Plasite® are
registered trademarks of Carboline Company.
|