Plasite庐 943
pattern, tooth or roughness.
TYPE
Plasite 943 is a vinyl ester repair material formulated with
Surface of sound coating surrounding repair area must
special corrosion resistant pigments and minimum length
be contamination free and sanded or lightly blasted prior
of time cure requirements.
to overlapping with Plasite 943 repair material.
INTENDED USE
APPLICATION
Plasite 943 is recommended as a chemical resistant spot
Apply Plasite 943 with supplied brush or plastic
repair material for Plasite vinyl ester lining systems. FOR
applicator to repair area. Overlap on surrounding
INDUSTRIAL USE ONLY!
coating, attempting to feather edge of overlap repair.
COVERAGE
The recommended minimum DFT of the Plasite 943
One Plasite 943 repair kit will cover a total of 3 sq. ft. of
repair shall be 40 mils.
spot repairs when applied at the recommended 40 mil
DFT.
SAFETY
SHELF LIFE
READ THIS NOTICE
1 month at 70掳F. Cooler temperatures will extend shelf
SAFETY AND MISCELLANEOUS EQUIPMENT
life.
For tank lining work or enclosed spaces, it is
POT LIFE
recommended that the operator provide himself with
30 minutes at 70掳F
clean coveralls and rubber soled shoes and observe
good personal hygiene. Certain personnel may be
SET TIME
sensitive to various types of resins which may cause
6 hours at 50掳F; 2 hours at 70掳F
dermatitis.
CURE TIME THE SOLVENT IN THIS COATING IS FLAMMABLE
48 hours at 50掳F; 24 hours at 70掳F AND CARE AS DEMANDED BY GOOD PRACTICE,
OSHA, STATE AND LOCAL SAFETY CODES, ETC.
COLOR
MUST BE FOLLOWED CLOSELY. Keep away from
Dark gray
heat, sparks and open flame and use necessary safety
equipment, such as, air mask, explosion-proof electrical
PACKAGING
equipment, non-sparking tools and ladders, etc. Avoid
Plasite 943 is supplied as a prepackaged repair kit. Kit
contact with skin and breathing of vapor or spray mist.
contents are:
When working in tanks, rooms and other enclosed
鈥? 1 鈥? Quart can part-filled with Plasite 943 pigmented spaces, adequate ventilation must be provided. Refer
to PLASITE Bulletin PA-3. Keep out of the reach of
liquid, Part I
鈥? 1 鈥? Two-ounce plastic bottle part-filled with Plasite children.
943 catalyst liquid, Part II
鈥? 1 鈥? Wooden mixing stick CAUTION - Read and follow all caution statements on
鈥? 1 鈥? Plastic applicator tool this product data sheet, material safety data sheet and
鈥? 1 鈥? 1鈥? brush container label for this product.
MIXING
This data sheet provides standard information on the
Add Plasite 943 Part I and Part II and mix thoroughly.
coating and application procedure. Since varying con-
ditions may not be covered, consult with your local sales
Spread the material on a flat board which extends the
representative or Carboline Technical Service
workable life. This is attributed to the dissipation of the
Department for further information.
heat generated by the exothermic reaction.
SURFACE PREPARATION
Remove all corrosion products, old coating, etc., from
Surface of area to be repaired.
Repair area surface must have neutral pH. Substrate
shall be clean, bright metal with a pronounced anchor
February 2004 252P
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to
verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for
coverage, performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE,
EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline庐 and Plasite庐 are
registered trademarks of Carboline Company.
|