3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
Material Safety Data Sheet
Copyright, 2006, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 05/11/2006
Supercedes Date: 03/28/2003
Document Group: 10-2794-5
Product Use:
Specific Use: Rubber and Gasket Bonding Adhesive
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
MAGNESIUM RESINATE 68611-24-5 20 - 30
METHYL ETHYL KETONE 78-93-3 20 - 30
POLYCHLOROPRENE 9010-98-4 10 - 20
MIXED HEXANE ISOMERS Mixture 10 - 20
N-HEXANE 110-54-3 7 - 13
TOLUENE 108-88-3 5 - 10
LIGHT SOLVENT NAPHTHA 64741-84-0 3- 7
MIXED HEPTANES Mixture 3- 7
CYCLOHEXANE 110-82-7 < 1.5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: yellow, solvent odor
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and
explode. Extremely flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and
flash back. May cause target organ effects. Contains a chemical or chemicals which can cause birth defects or other
_________________________________________________________________________________________________
Page 1 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
reproductive harm.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
May be absorbed through skin and cause target organ effects.
Inhalation:
Upper Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
and throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, nausea, diarrhea and vomiting.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Prolonged or repeated exposure may cause:
Liver Effects: Signs/symptoms may include loss of appetite, weight loss, fatigue, weakness, abdominal tenderness and
jaundice.
Central Neuropathy: Signs/symptoms may include irritability, memory impairment, personality changes, sleep disorders, and
decreased ability to concentrate.
Peripheral Neuropathy: Signs/symptoms may include tingling or numbness of the extremities, incoordination, weakness of
the hands and feet, tremors and muscle atrophy.
Kidney Effects: Signs/symptoms may include reduced or absent urine production, increased serum creatinine, lower back
pain, increased protein in urine, and increased blood urea nitrogen (BUN).
Methyl ethyl ketone has been shown to potentiate the neurotoxic effects of n-hexane.
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
_________________________________________________________________________________________________
Page 2 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting. Give victim two glasses of water. Never give anything by mouth to an unconscious
person. Get immediate medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
No Data Available
Autoignition temperature
-14.00 潞F [Test Method: Tagliabue Closed Cup] [Details:
Flash Point
CONDITIONS: (petroleum distillate)]
1.00 % volume
Flammable Limits - LEL
11.50 % volume
Flammable Limits - UEL
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Extremely
flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards,
respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information
on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up
by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-
sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to
disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build
dikes to prevent entry into sewer systems or bodies of water. Avoid contact with incompatible materials listed in the Reactivity Data
Section. Cover spill area with a fire-extinguishing foam. An aqueous film forming foam (AFFF) is recommended. Working from
around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix
in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible using non-sparking tools. Clean up
_________________________________________________________________________________________________
Page 3 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
residue with an appropriate organic solvent. Read and follow safety precautions on the solvent label and MSDS. Place in a metal
container approved for transportation by appropriate authorities. Seal the container. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat,
sparks, open flame, pilot lights and other sources of ignition. Ground containers securely when transferring contents. Wear low static
or properly grounded shoes. Avoid breathing of vapors, mists or spray. Avoid static discharge. Avoid eye contact with vapors, mists,
or spray. Avoid contact with oxidizing agents.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container
tightly closed. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide local exhaust ventilation at transfer points. Provide appropriate local exhaust
ventilation on open containers.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Polyethylene/Ethylene Vinyl Alcohol.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M
Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
CYCLOHEXANE ACGIH TWA 100 ppm
CYCLOHEXANE OSHA TWA 300 ppm Table Z-1
_________________________________________________________________________________________________
Page 4 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
N-HEXANE ACGIH TWA 50 ppm Skin Notation*
N-HEXANE OSHA TWA, Vacated 50 ppm Table Z-1A
N-HEXANE OSHA TWA 500 ppm Table Z-1A
METHYL ETHYL KETONE ACGIH TWA 200 ppm
METHYL ETHYL KETONE ACGIH STEL 300 ppm
METHYL ETHYL KETONE OSHA TWA 200 ppm Table Z-1A
METHYL ETHYL KETONE OSHA STEL 300 ppm Table Z-1A
TOLUENE ACGIH TWA 50 ppm Skin Notation*; Table A4
TOLUENE CMRG STEL 75 ppm Skin Notation*
TOLUENE OSHA TWA, Vacated 100 ppm
TOLUENE OSHA STEL, Vacated 150 ppm
TOLUENE OSHA TWA 200 ppm Table Z-2
TOLUENE OSHA CEIL 300 ppm Table Z-2
* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,
either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
yellow, solvent odor
Odor, Color, Grade:
Liquid
General Physical Form:
No Data Available
Autoignition temperature
-14.00 潞F [Test Method: Tagliabue Closed Cup] [Details:
Flash Point
CONDITIONS: (petroleum distillate)]
1.00 % volume
Flammable Limits - LEL
11.50 % volume
Flammable Limits - UEL
140.00 潞F
Boiling point
>=2.50 [Ref Std: AIR=1]
Vapor Density
120.0000 mmHg [Details: CONDITIONS: @ 68F]
Vapor Pressure
0.880 [Ref Std: WATER=1]
Specific Gravity
No Data Available
pH
No Data Available
Melting point
>=2.00 [Ref Std: ETHER=1]
Evaporation rate
Approximately 1.14 lb HAPS/lb solids [Test Method: Calculated]
Hazardous Air Pollutants
21 % weight [Test Method: Calculated]
Hazardous Air Pollutants
1.5 lb HAPS/gal [Test Method: Calculated]
Hazardous Air Pollutants
550 g/l [Test Method: South Cost Air Qual Mgmt Dist] [Details:
Volatile Organic Compounds
CONDITIONS: Rule 443.1, calculated]
62.00 % weight
Percent volatile
550 g/l [Test Method: South Cost Air Qual Mgmt Dist] [Details:
VOC Less H2O & Exempt Solvents
CONDITIONS: Rule 443.1, calculated]
_________________________________________________________________________________________________
Page 5 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
1300.0 - 2600.0 centipoise
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Strong oxidizing agents
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Aldehydes During Combustion
Carbon monoxide During Combustion
Carbon dioxide During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste product
in a permitted hazardous waste facility.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable), D035 (Methyl ethyl ketone)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
_________________________________________________________________________________________________
Page 6 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
62-1300-0635-6, 62-1300-2630-5, 62-1300-2631-3, 62-1300-2632-1, 62-1300-5530-4, 62-1300-6530-3, 62-1300-7530-2, 62-
1300-8530-1, 62-1300-9530-0
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No % by Wt
TOLUENE 108-88-3 5 - 10
METHYL ETHYL KETONE 78-93-3 20 - 30
N-HEXANE 110-54-3 7 - 13
CYCLOHEXANE 110-82-7 < 1.5
This material contains a chemical which requires export notification under TSCA Section 12[b]:
Ingredient (Category if applicable) C.A.S. No Regulation Status
N-HEXANE 110-54-3 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
CYCLOHEXANE 110-82-7 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
STATE REGULATIONS
Contact 3M for more information.
CALIFORNIA PROPOSITION 65
Ingredient C.A.S. No. Classification
TOLUENE 108-88-3 *Developmental Toxin
* WARNING: contains a chemical or chemicals which can cause birth defects or other reproductive harm.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
_________________________________________________________________________________________________
Page 7 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
WHMIS: Hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 3 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Revision Changes:
Section 16: NFPA hazard classification heading was modified.
Section 3: Other potential health effects heading was modified.
Copyright was modified.
Section 8: Exposure guidelines data source legend was modified.
Section 3: Immediate physical hazard(s) was modified.
Section 5: Fire fighting procedures information was modified.
Section 5: Unusual fire and explosion hazard information was modified.
Section 7: Handling information was modified.
Section 7: Storage information was modified.
Section 8: Engineering controls information was modified.
Section 8: Eye/face protection phrase was modified.
Section 15: 311/312 hazard categories heading was modified.
Section 15: International regulations information was modified.
Section 15: State regulations information was modified.
Section 15: US federal regulations information was modified.
Section 15: WHMIS regulations information was modified.
Section 10: Hazardous polymerization heading was modified.
Section 15: TSCA section 12[b] text was modified.
Section 3: Other health effects information was modified.
Section 16: NFPA explanation was modified.
Section 15: Inventories information was modified.
Section 15: EPCRA 313 text was modified.
Section 15: California proposition 65 heading was modified.
Section 15: California proposition 65 reproductive harm warning was modified.
Section 12: Ecotoxicological information heading was modified.
_________________________________________________________________________________________________
Page 8 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Grip(TM) Rubber and Gasket Adhesive 1300 05/11/2006
Section 12: Chemical fate information heading was modified.
Section 8: Exposure guidelines legend was modified.
Section 8: Exposure guideline note was modified.
Section 9: Property description for optional properties was modified.
Section 16: NFPA hazard classification for special hazards was modified.
Section 3: Other health effects information (reproductive hazards) was modified.
Section 3: Other potential health effects was modified.
Section 12: Ecotoxicological phrase was modified.
Section 12: Chemical Fate phrase was modified.
Section 2: Ingredient phrase was added.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 9 of 9
|