Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
1. IDENTIFICATION OF MATERIAL & SUPPLIER
FYREWRAP庐
Brand Name:
Insulfrax
Product Group:
Fyrewrap庐 Structural Blanket 96
Other Names:
None Allocated
UN Number:
None Allocated
DG Class
None Allocated
Packaging Group
None Allocated
Hazchem Code
Not Scheduled
Poisons Schedule
Thermal Insulation
Product Use
Manufacturer/Supplier: Unifrax Limited Unifrax Australia Pty. Ltd.
Mill Lane, Rainford 336 Settlement Road
St. Helens Thomastown 3074
Merseyside 20 WA118L Victoria
UK Australia
Unifrax France
17 Rue Antoine Durafour
Lorette 20 42420
France.
See page 8
Contact:
2. HAZARDS IDENTIFICATION
Flammability
Non flammable
Fire Hazards:
Non explosive
Explosive Hazards:
Temporary mild irritation to eyes, skin and upper respiratory
Health Hazards:
system. Pre-existing skin and respiratory conditions including
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 1
Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
2. Hazards Identification cont鈥檇:
dermatitis, asthma and chronic lung disease might be
aggravated by exposure.
3. COMPOSITION AND INFORMATION ON INGREDIENTS
Component CAS Proportion
Alkaline earth silicate fibres 436 083 99 7 (SiO ) 60 鈥? 70%
虏
(CaO + MgO) 30 鈥? 40%
4. FIRST AID MEASURES
In case of skin irritation rinse affected areas with water and
Skin:
wash gently. Do not rub or scratch exposed skin.
In case of eye contact flush abundantly with water; have
Eyes:
eye bath available. Do not rub eyes.
If these become irritated move to a dust free area, drink
Nose & Throat:
water and blow nose. If symptoms persist, seek medical
advice.
5. FIRE FIGHTING MEASURES.
Not Flammable and not explosive. Packaging and
Fire Explosion Hazard:
surrounding materials may be combustible.
None Allocated.
Hazchem Code:
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 2
Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
6. ACCIDENTAL RELEASE MEASURES
Where abnormally high dust concentrations occur, provide the workers with appropriate
protective equipment as detailed in Section 8.
Prevent further dust dispersion eg damping the materials.
Methods for Cleaning Up
Pick up large pieces and use a vacuum cleaner fitted with high efficiency filter (HEPA)
If brushing is used, ensure that the area is wetted down first.
Do not use compressed air for clean-up.
Do not allow to be wind blown.
Do not flush spillage to drain and prevent from entering natural watercourses.
Check for local regulations, which may apply.
7. HANDLING & STORAGE
Handling:
Handling can be a source of dust emission. The process or processes should be
designed to limit the amount of handling. Whenever possible, handling should be
carried out under controlled conditions (ie., use dust exhaust system).
Regular good housekeeping will minimise secondary dust dispersal.
Storage:
Store in original packaging in dry area whilst awaiting use.
Always use sealed and visibly labeled containers.
Avoid damaging containers.
Reduce dust emission during unpacking.
Emptied containers, which may contain debris, should be cleaned before disposal or
recycling.
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 3
Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
8. EXPOSURE CONTROLS & PERSONAL PROTECTION
Engineering Controls
Review your application(s) in order to identify potential sources of dust exposure.
Local exhaust ventilation, which collects dust at source, can be used. Eg down draft
tables, emission controlling tools and material handling equipment.
Keep the workplace clean. Use a vacuum cleaner fitted with an HEPA filter; avoid
brushing and using compressed air.
Personal Protection
Wear gloves and work clothes which are loose fitting at the
Skin Protection:
neck and wrists. Soiled clothes should be cleaned to
remove excess fibres before being taken off (eg. Use
vacuum cleaner, not compressed air).
As necessary, wear goggles or safety glass with side
Eye Protection:
shields.
Respirators are recommended. All respirators used shall
Respiratory Protection:
comply with the provisions of AS1715 and 1716.
In case of higher concentrations or where the
concentration is not known, please seek advice from your
company and/or your supplier.
9. PHYSICAL & CHEMICAL PROPERTIES
White
Appearance:
>1330掳 C
Melting Point:
Not applicable
Boiling Point:
Not applicable
Vapour Pressure:
2.60
Specific Gravity:
Not soluble in water
Solubility in Water:
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 4
Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
9. Physical & Chemical Properties cont鈥檇:
Not applicable
Vapour Density:
Not applicable
pH Value
10. STABILITY & REACTIVITY
Stable under normal conditions of use.
Stability:
Upon heating above 900掳 for sustained periods, this
C
Hazardous Reactions
amorphous material begins to transform to mixtures of
Decomposition Products
crystalline phases. For further information refer to
Section 16.
11. TOXICOLOGICAL INFORMATION
Irritant Properties
When tested using approved methods (Directive 67/548/EC, Annex V, Method B4),
fibres contained in this material give negative results. All man made mineral fibres, like
some natural fibres, can produce a mild irritation resulting in itching or rarely, in some
sensitive individuals, in slight reddening. Unlike other irritant reactions this is not the
result of allergy or chemical skin damage but is caused by a temporary mechanical
effect.
Other Animal Studies
These materials have been designed to allow rapid clearance from tissue. And this low
biopersistence has been confirmed in many studies using EU protocol ECB/TM/27 (rev
7) and the German method specified in TRGS 905 (1999). When inhaled, even at very
high doses, they do not accumulate to any level capable of producing a serious adverse
biological effect. In lifetime chronic studies there was no exposure-related effect more
than would be seen with any 鈥渋nert鈥? dust. Subchronic studies at the highest doses
achievable produced, at worst, a transient mild inflammatory response. Fibres with the
same ability to persist in tissue do not produce tumours when injected into the peritoneal
cavity of rats.
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 5
Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
12. ECOLOGICAL INFORMATION
These products are inert materials, which remain stable overtime.
No adverse effects of this material on the environment are anticipated.
13. DISPOSAL CONSIDERATIONS
Waste shall be placed in containers, plastic bags or other
Waste Disposal:
methods which will prevent Fiber and/or dust emission and
disposed of in accordance with the local waste disposal
authority requirements. There may be specific regulations
at the Local, State or Federal level that pertain to this
material.
14. TRANSPORT INFORMATION
No special transport requirements are necessary.
Ensure that dust is not wind blown during transportation.
15. REGULATORY INFORMATION
R36/37/38 Irritating to eyes, respiratory system and skin.
Risk Statement:
S22 Do not breathe dust. S52 Avoid contact with eyes. S38
Safety Statement:
In insufficient ventilation, wear suitable respiratory equipment.
S40 To clean floor and all objects contaminated by this
Material, use AS approved HEPA fitted vacuum cleaner.
S36/37/39 Wear suitable protective clothing, gloves and eye/
Face protection.
Harmful, irritant.
Hazard Category:
Not scheduled.
Poisons Schedule:
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 6
Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
15. Regulatory Information cont鈥檇:
Regulatory status in the EU, comes from European Directive 67/548/EEC, on the
classification, labeling and packaging of dangerous substances and preparations as
modified by Directive 97/69/EEC.
According to Directive 67/548/EEC, the fibre contained in this product is a mineral wool
belonging to the group of 鈥渕an made vitreous (silicate) fibres with random orientation
with alkaline oxide and alkali earth oxide (Na O+K O+CaO+MgO+BaO) content greater
虏 虏
than 18% by weight鈥?.
Under Directive 67/548/EEC all types of man made vitreous (silicate) fibres are classified
as 鈥渋rritant鈥? despite the fact that testing by the appropriate EU method (B4 in annex 5 of
Directive 67/548/EEC) is providing no response and would not result in irritant
classification.
Under criteria listed in nota Q of Directive 67/548/EEC, AES wools are exonerated from
carcinogen classification because of low pulmonary biopersistence measured by the
methods specified in Europe.
16. OTHER INFORMATION
Useful References (the directives which are cited must be considered in their
amended version)
Council Directive 89/391/EEC dated 12 June 1989 鈥渙n the introduction of measures to
encourage improvements in the safety and health of workers at work鈥? (OJEC L 183 of
29 June 1989,p.1)
Council Directive 67/548/EEC on the 鈥渁pproximation of the laws, regulations and
administrative provision relating to the classification, packaging and labelling of
dangerous substances as modified and adapted to the technical progress鈥? (OJEC L 196
of 16 August 1967,p.1 and its modifications and adaptations to technical progress).
Commission Directive 97/69/EC of 5 December 1997 鈥渁dapting to technical progress for
the 23rd time Council Directive 67/548/EEC, (OJEC L 343 Official Journal of the
European Communities, 13/12/97, p.19).
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 7
Unifrax Australia Pty. Ltd.
326 Settlement Road
Thomastown, VIC 3074
FYREWRAP庐
ACN 093 625 757
Ph: (03) 9463 0000 Fax: (03) 9464 1176
MATERIAL SAFETY DATA SHEET
Classified as Hazardous according to criteria of Worksafe Australia
CONTACT DETAILS:
During Business Hours Ph: +61 3 9463 0000
Contact:
Ph: 1300 797 888
Customer Service Toll Free:
Alan Smith
Emergency / After Hours Contact:
Ph: 0409 288 916
NOTICE: The information presented herein is based on data considered to be accurate
as of the date of preparation of this Material Safety Data Sheet. However, no
warranty or representation, express or implied, is made as to the accuracy or
completeness of the foregoing data and safety information, nor is any
authorisation given or implied to practise any patented invention without
licence. In addition, no responsibility can be assumed by the vendor for any
damage or injury resulting from abnormal use, from any failure to adhere to
recommended practices, or from any hazards inherent in the nature of the
product.
... End Of Report ...
Authorised by: Alan Smith
Version: 1.2
Control Status: Controlled Document
Created on: 01/08/07 8
|