Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

N/A

File Name: alexlind_com_au---duothane_partapds.asp
                                                                                                            Page 1 of 2




DUOTHANE PART A

USES:
1. May be used to coat ALL timber species and particle board.
2. Mix DUOTHANE FAST A with DUOTHANE PART B for a quick drying first coat.
3. Mix DUOTHANE PART A with DUOTHANE PART B for a hard wearing top coat with excellent flow
properties and resistance to U.V. light.
4. May be applied over TIMBER SEAL.


FLOOR PREPARATION:
New Floors: Fine sand and vacuum thoroughly.
Old Floors: Clean with hot water and detergent .Roughen surface completely with 150 mesh screenback and
vacuum thoroughly. Wipe floor with URETHANE COATINGS THINNERS. Test for compatibility by
applying DUOTHANE on a small section of floor first. If 'crayters' or 'fisheyes' appear, add 10mls of
FLOWMAX Anti rejection Fluid per litre of DUOTHANE and refer to FLOWMAX directions.


APPLICATION:
1. Carefully measure and mix equal quantities of DUOTHANE PART A and DUOTHANE PART B and
stir thoroughly.
2. Apply with mohair roller or brush, allow 4 -6 hours to dry. Do not return unused material to can. New
cork and timber floors will need 3 and 2 coats respectively, sand with 150 grit screenback between coats.
3. Soak brush or roller in URETHANE COATINGS CLEANING SOLVENT. Dry brush or roller before
using.
Page 2 of 2




COVERAGE: 10m虏 per litre. URETHANE COATINGS THINNERS may be added if DUOTHANE has
thickened, or if a higher coverage and a thinner coat is required.


MAINTENANCE: DUOTHANE requires 7 -10 days to fully cure. Avoid heavy traffic during this period.
After curing period sweep floor regularly and wash with warm water and a little methylated spirits. Use
protective pads under legs of furniture.


SHELF LIFE: This product is best if used within 12 months from manufacture (refer to batch number),
when stored in unopened containers under normal conditions of temperature and humidity.


SAFETY DIRECTIONS: Usage of this material must be under well ventilated conditions to minimise
inhalation of vapours. Wear respirator with filters that conform with AS1716. Asthmatics, the very young,
elderly people and pets should leave the site during the first 24 hours. Prevent skin contact by wearing
impervious gloves. Breathing of vapour is harmful and may cause lung irritation and allergic respiratory
reaction. Irritates skin and eyes. Keep tin firmly lidded, as this product cures when exposed to air. In case of
spillage, absorb into dry sand or dirt. Remove from work area and cover with water for 24 hours prior to
disposal.


WARNING FLAMMABLE: Contains 280gms per litre of Aromatic Hydrocarbons. This tin contains
volatile and flammable solvents and when applying the contents adequate ventilation to the outside must be
provided. All potential sources of ignition (open flames, pilot lights, furnaces, spark producing electrical
switches, etc.) must be eliminated in or near the working area. DO NOT SMOKE. Keep tin closed when not
in use.


FIRST AID: If affected by inhalation of vapour, remove to fresh air. If breathing difficulty persists or
occurs later, consult a doctor and have label ready. If swallowed, do NOT induce vomiting. Give water or
milk. CONTACT DOCTOR OR POISONS INFORMATION CENTRE Australia 131126. In case of eye
contact, flush immediately with water for fifteen minutes and call a doctor. In case of skin contact, remove
contaminated clothing and wash skin first with methylated spirits, then with soap and water.

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
alexlind_com_au---bostik_ultralevel_slmsds.asp N/A
alexlind_com_au---bostik_ultrasetmsds.asp N/A
alexlind_com_au---bostik_ultra_np_primermsds.asp N/A
alexlind_com_au---bostik_ultra__np__primerpds.asp N/A
alexlind_com_au---chinawoodoilpds.asp N/A
alexlind_com_au---d519estapolglosssatinandmattpds.asp N/A
alexlind_com_au---deckingoilmsds.asp 138-86-3 5989-27-5
alexlind_com_au---deckingoilpds.asp N/A
alexlind_com_au---deckingstainpds.asp N/A
alexlind_com_au---dimension4pds.asp N/A
alexlind_com_au---duothane_partapds.asp N/A
alexlind_com_au---dwdpds.asp N/A
alexlind_com_au---endure2packmsds.asp 872-50-4 34590-94-8
alexlind_com_au---exterioroilpds.asp N/A
alexlind_com_au---finebuffingoilpds.asp N/A
alexlind_com_au---flatproofpds.asp N/A
alexlind_com_au---floorcleanpds.asp N/A
alexlind_com_au---floorclearglosspds.asp N/A
alexlind_com_au---floorproofglosspds.asp N/A
alexlind_com_au---floorproofthinnersmsds.asp 1330-20-7 108-65-6
alexlind_com_au---floorproofthinnerspds.asp N/A
alexlind_com_au---floorsealpds.asp N/A
alexlind_com_au---floortecglosspds.asp N/A
alexlind_com_au---fungishieldpds.asp N/A
alexlind_com_au---gardenfurnitureoilmsds.asp 138-86-3 5989-27-5
alexlind_com_au---hard_burnishingoilmsds.asp 138-86-3 5989-27-5
alexlind_com_au---highbuildenduremsds.asp 872-50-4 34590-94-8
alexlind_com_au---hispeedfinishingoilmsds.asp 138-86-3 5989-27-5
alexlind_com_au---limingsolutionpds.asp N/A
alexlind_com_au---mastertouchpolishmsds.asp N/A
alexlind_com_au---mastertouchpolishpds.asp N/A
alexlind_com_au---maxithanecleanupsolventpds.asp N/A
alexlind_com_au---maxithaneglossnypds.asp N/A
alexlind_com_au---maxithaneglosspds.asp N/A
alexlind_com_au---maxithanereducerpds.asp N/A
alexlind_com_au---maxithanesatinpds.asp N/A
alexlind_com_au---maxithanewetedgeextendermsds.asp 148462-57-1 148462-58-2 872-50-4
alexlind_com_au---modifiedoilsatinpds.asp N/A
alexlind_com_au---monothanehs50glosspds.asp N/A
alexlind_com_au---proofsealpds.asp N/A
alexlind_com_au---prooftinitpds.asp N/A
alexlind_com_au---quicksteppds.asp N/A
alexlind_com_au---renewmsds.asp N/A
alexlind_com_au---sandingsealerpds.asp N/A
alexlind_com_au---scandinavianoilpds.asp N/A
alexlind_com_au---seamasterpsd.asp N/A
alexlind_com_au---sparmarinepds.asp N/A
alexlind_com_au---squeakycleanmsds.asp N/A
alexlind_com_au---timberfillpds.asp N/A
alexlind_com_au---timbersealpds.asp N/A

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC