DATA SHEET
FEAST WATSON Sanding Sealer
PRODUCT CODE 870-94641 Data Sheet No. AUDW0744
APPROVALS NA
Description
FEAST WATSON Sanding Sealer is a colourless solvent based clear for sealing bare timber under oil or water based clear
finishes.
Features Benefits
Clear wood sealer For preparing porous open grained timber for clear polyurethanes.
Fills grain & sands easily Gives a better, smoother finish with less effort.
Quick drying Reduces time on the job.
Uses
Use FEAST WATSON Sanding Sealer as an interior timber grain sealer prior to applying FEAST WATSON oil or water based
polyurethanes, to give a smooth finish to the topcoats.
Performance Guide
Weather Not suitable for exterior use. Salt Unaffected by splash or spillage
Heat Up to 120C. Prolonged exposure to 120C heat Water Resists condensation and water with approved
will cause embrittlement. topcoat.
Solvent Resists alcohol and hydrocarbons. Film is Abrasion Good when topcoated.
liable to attack from other strong solvents.
Alkali Suitable for splash (Dilute only)
Acid Suitable for splash (Dilute only)
Typical Properties and Application Data
Gloss Level Flat Thinner Not required
Gloss Level Ind Spread Rate 10.0 sqm/L
Components 1.0
Volume Solids 35.0
Colour Dries to colourless clear, although it Toxicity Lead free. Dry film is non-toxic and
appears milky in the can. conforms to AS1647, Part 3.
Number of Coats 1 Wet film per coat Recommended 100 碌m
Dry film per coat Recommended 35 碌m
8 hours
Touch Dry 3 hours Recoat
Application Method
Data Sheet FEAST WATSON Sanding Sealer
DuSpec Data Code AUDW0744 Page No 1 of 3
Issue No 3.0 Date Issued 23/01/2006
DATA SHEET
FEAST WATSON Sanding Sealer
Data Sheet No. AUDW0744
Application Guide
Surface Preparation
All timber surfaces must be thoroughly clean, dry and completely free from wax, floor polishes, and other contaminents. Wash with
mineral turpentine if needed to remove wax and grease, allow 24 hours, and lightly sand dressed surfaces using 180 - 240 gri
Application Procedure and Equipment
Stir thoroughly before and during use with a broad flat stirrer to maintain a uniform solution.
Apply one coat with at least 8 hours drying before sanding.
Always lay off along the grain.
Brush, short-nap roller or pad
Health and Safety
MSDS 1280 Health Effects For detailed information refer to product label
Number and the current Material Safety Data Sheet
available through Sales and Customer Service
Offices. Health Effects: Splashes to eyes will
cause irritation. Prolonged contact with liquid is
harmful and inhalation of vapour and spray
mists may produce respiratory irritation and
headaches.
Flammability: This product is flammable Protective Personal Protective Equipment: Wear eye
Flammability
Equipment protection, protective clothing and gloves, and if
spraying wear a respirator with a combined
vapour/particulate cartridge.
Disposal Do not dispose down the drain. Refer to your
local council for correct disposal procedures
In the case of emergency please call 1800 033 111
Precautions and Limitations
Do not apply if surface temperature is below 10C or conditions indicate it will fall below 10C during drying period.
Only apply to new timber or to timber from which all previous finishes have been removed.
Moisture content of timber should be close to
Transport and Storage
Pack A 870-94641
Sizes 4 Litre 1 Litre 500ml 250ml Flash point 36C
UN Number 1263
Weight 4.2 Kg 1.1 Kg 524g 262g
Dangerous 3 Package II
Goods Class Group
Shipment PAINTS
Name
Data Sheet FEAST WATSON Sanding Sealer
DuSpec Data Code AUDW0744 Page No 2 of 3
Issue No 3.0 Date Issued 23/01/2006
DATA SHEET
FEAST WATSON Sanding Sealer
Data Sheet No. AUDW0744
Disclaimer
Dulux and Other marks followed by 庐 are registered trademarks. Marks followed by the symbol of 鈩? are trademarks.
The data provided within the Duspec system is correct at the time of publication, however it is the responsibility of those using this information to
check that it is current prior to specifying or using any of these coating systems.
DISCLAIMER: Any advice, recommendation, information, assistance or service provided by any of the divisions of Orica Consumer Products in
relation to goods manufactured by it or their use and application is given in good faith and is believed by Orica Consumer Products to be appropriate
and reliable. However, any advice, recommendation, information, assistance or service provided by Orica Consumer Products is provided without
liability or responsibility PROVIDED THAT the foregoing shall not exclude, limit, restrict or modify the right entitlements and remedies conferred
upon any person or the liabilities imposed upon Orica Consumer Products by any condition or warranty implied by Commonwealth, State or
Territory Act or ordinance void or prohibiting such exclusion limitation or modification. Coating systems can be expected to perform as indicated on
the Duspec Spec Sheet so long as applications and application procedures of the individual products are followed as recommended on the
appropriate Product data Sheet. "Orica" "Dulux" "Berger" "Berger
Gold Label" "Hadrian" "Walpamur" "Levene" "Acratex" and Other marks followed by 庐 are registered trademarks of Orica Australia Pty Ltd ABN 99
004 117 828. Marks followed by the symbol 鈩? are trademarks.
Please note that this document is only valid for 60 days from the date of issue.
Orica Consumer Products 1970 Princes Highway Clayton, Victoria 3168 AU ABN 99 004 117 828
Data Sheet FEAST WATSON Sanding Sealer
DuSpec Data Code AUDW0744 Page No 3 of 3
Issue No 3.0 Date Issued 23/01/2006
|