AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 1 of 12
Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
AMMO-CARB
STATEMENT OF HAZARDOUS NATURE
CONSIDERED A HAZARDOUS SUBSTANCE ACCORDING TO OSHA 29 CFR
1910.1200.
SUPPLIER
Company: Aquarium Pharmaceuticals Incorporated Company: Aquarium Pharmaceuticals Incorporated
Address: Address:
PO Box 218 50 East Hamilton Street
Chalfont Chalfont
PA, 18914-0218 PA, 18914
USA USA
Telephone: +1 215 822 8181 Telephone: +1 215 822 8181
Emergency Tel: +1800 222 1222 (US Only)
PRODUCT USE
Used according to manufacturers directions. For product 80.
SYNONYMS
Section 2 - COMPOSITION / INFORMATION ON INGREDIENTS
NAME CAS RN %
zeolites 1318-02-1 80-90
carbon, steam activated - not regulated 7440-44-0 10-20
water 7732-18-5 1-5
Section 3 - HAZARDS IDENTIFICATION
CANADIAN WHMIS SYMBOLS
EMERGENCY OVERVIEW
RISK
May cause fire.
Cumulative effects may result following exposure*.
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 2 of 12
Section 3 - HAZARDS IDENTIFICATION
Exposure may produce irreversible effects*.
May produce discomfort of the eyes and respiratory tract*. *(limited evidence)
POTENTIAL HEALTH EFFECTS
ACUTE HEALTH EFFECTS
SWALLOWED
The material has NOT been classified as "harmful by ingestion". This is because
of the lack of corroborating animal or human evidence. The material may still be
damaging to the health of the individual, following ingestion, especially where
pre-existing organ (e.g. liver, kidney) damage is evident. Present definitions
of harmful or toxic substances are generally based on doses producing mortality
(death) rather than those producing morbidity (disease, ill-health).
Gastrointestinal tract discomfort may produce nausea and vomiting. In an
occupational setting however, unintentional ingestion is not thought to be cause
for concern.
EYE
There is some evidence to suggest that this material can cause
eye irritation and damage in some persons.
SKIN
The material is not thought to produce adverse health effects or skin irritation
following contact (as classified using animal models). Nevertheless, good
hygiene practice requires that exposure be kept to a minimum and that suitable
gloves be used in an occupational setting.
Entry into the blood-stream, through, for example, cuts, abrasions or lesions,
may produce systemic injury with harmful effects. Examine the skin prior to the
use of the material and ensure that any external damage is suitably protected.
INHALED
There is some evidence to suggest that this material, if inhaled, can irritate
the throat and lungs of some persons.
Although inhalation is not thought to produce harmful effects, the material may
still produce health damage, especially where pre-existing organ (e.g. liver,
kidney) damage is evident. Present definitions of harmful or toxic substances
are generally confined to doses producing mortality (death) rather than those
producing morbidity (disease, ill-health).
There is some evidence to suggest that the material can cause respiratory
irritation in some persons. The body's response to such irritation can cause
further lung damage.
Persons with impaired respiratory function, airway diseases and conditions such
as emphysema or chronic bronchitis, may incur further disability if excessive
concentrations of particulate are inhaled.
CHRONIC HEALTH EFFECTS
Long term exposure to high dust concentrations may cause changes in lung
function i.e. pneumoconiosis; caused by particles less than 0.5 micron
penetrating and remaining in the lung. Prime symptom is breathlessness; lung
shadows show on X-ray. Substance accumulation, in the human body, may occur and
may cause some concern following repeated or long-term occupational exposure.
There has been some concern that this material can cause cancer or mutations but
there is not enough data to make an assessment.
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 3 of 12
Section 4 - FIRST AID MEASURES
SWALLOWED
- Immediately give a glass of water.
- First aid is not generally required. If in doubt, contact a Poisons
Information Center or a doctor.
EYE
If this product comes in contact with the eyes:
- Wash out immediately with fresh running water.
- Ensure complete irrigation of the eye by keeping eyelids apart and away from
eye and moving the eyelids by occasionally lifting the upper and lower lids.
- If pain persists or recurs seek medical attention.
- Removal of contact lenses after an eye injury should only be undertaken by
skilled personnel.
SKIN
If skin or hair contact occurs:
- Flush skin and hair with running water (and soap if available).
- Seek medical attention in event of irritation.
INHALED
- If fumes or combustion products are inhaled remove from contaminated area.
- Other measures are usually unnecessary.
NOTES TO PHYSICIAN
Treat symptomatically.
Section 5 - FIRE FIGHTING MEASURES
Flash Point (F): Not Applicable
Lower Explosive Limit (%): Not Applicable
Upper Explosive Limit (%): Not Applicable
Autoignition Temp (F): Not Applicable
EXTINGUISHING MEDIA
- There is no restriction on the type of extinguisher which may be used.
Use extinguishing media suitable for surrounding area.
FIRE FIGHTING
- Alert Emergency Responders and tell them location and nature of hazard.
- Wear breathing apparatus plus protective gloves for fire only.
- Prevent, by any means available, spillage from entering drains or water
course.
- Use fire fighting procedures suitable for surrounding area.
- Do not approach containers suspected to be hot.
- Cool fire exposed containers with water spray from a protected location.
- If safe to do so, remove containers from path of fire.
- Equipment should be thoroughly decontaminated after use.
GENERAL FIRE HAZARDS/HAZARDOUS COMBUSTIBLE PRODUCTS
- Solid which exhibits difficult combustion or is difficult to ignite.
- Avoid generating dust, particularly clouds of dust in a confined or
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 4 of 12
Section 5 - FIRE FIGHTING MEASURES
unventilated space as dusts may form an explosive mixture with air, and any
source of ignition, i.e. flame or spark, will cause fire or explosion. Dust
clouds generated by the fine grinding of the solid are a particular hazard;
accumulations of fine dust may burn rapidly and fiercely if ignited.
- Dry dust can be charged electrostatically by turbulence, pneumatic transport,
pouring, in exhaust ducts and during transport.
- Build-up of electrostatic charge may be prevented by bonding and grounding.
- Powder handling equipment such as dust collectors, dryers and mills may
require additional protection measures such as explosion venting.
Decomposition may produce toxic fumes of, carbon dioxide (CO2), other pyrolysis
products typical of burning organic material.
May emit poisonous fumes.
May emit corrosive fumes.
FIRE INCOMPATIBILITY
Avoid contamination with oxidizing agents i.e. nitrates, oxidizing acids,
chlorine bleaches, pool chlorine etc. as ignition may result.
PERSONAL PROTECTION
Glasses:
Chemical goggles.
Gloves:
PVC chemical resistant type.
Respirator:
Particulate
Section 6 - ACCIDENTAL RELEASE MEASURES
MINOR SPILLS
- Clean up all spills immediately.
- Avoid breathing dust and contact with skin and eyes.
- Wear protective clothing, gloves, safety glasses and dust respirator.
- Use dry clean up procedures and avoid generating dust.
- Sweep up, shovel up or vacuum up (consider explosion-proof machines designed
to be grounded during storage and use).
- Place spilled material in clean, dry, sealable, labeled container.
MAJOR SPILLS
Moderate hazard.
- CAUTION: Advise personnel in area.
- Alert Emergency Responders and tell them location and nature of hazard.
- Control personal contact by wearing protective clothing.
- Prevent, by any means available, spillage from entering drains or water
courses.
- Recover product wherever possible.
- IF DRY: Use dry clean up procedures and avoid generating dust. Collect
residues and place in sealed plastic bags or other containers for disposal. IF
WET: Vacuum/shovel up and place in labelled containers for disposal.
- ALWAYS: Wash area down with large amounts of water and prevent runoff into
drains.
- If contamination of drains or waterways occurs, advise emergency services.
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 5 of 12
Section 6 - ACCIDENTAL RELEASE MEASURES
ACUTE EXPOSURE GUIDELINE LEVELS (AEGL) (in ppm)
AEGL 1: The airborne concentration of a substance above which it is predicted
that the general population, including susceptible individuals, could
experience notable discomfort, irritation, or certain asymptomatic nonsensory
effects. However, the effects are not disabling and are transient and
reversible upon cessation of exposure.
AEGL 2: The airborne concentration of a substance above which it is predicted
that the general population, including susceptible individuals, could
experience irreversible or other serious, long-lasting adverse health effects
or an impaired ability to escape.
AEGL 3: The airborne concentration of a substance above which it is predicted
that the general population, including susceptible individuals, could
experience life-threatening health effects or death.
EMERGENCY RESPONSE PLANNING GUIDELINES (ERPG)
The maximum airborne concentration below which it is believed that nearly all
individuals could be exposed for up to one hour WITHOUT experiencing or developing
life-threatening health effects is:
carbon, steam activated - not regulated 500 mg/m続
irreversible or other serious effects or symptoms which could
impair an individual's ability to take protective action is:
carbon, steam activated - not regulated 10 mg/m続
other than mild, transient adverse effects
without perceiving a clearly defined odour is:
carbon, steam activated - not regulated 6 mg/m続
The threshold concentration below which most people.
will experience no appreciable risk of health effects:
carbon, steam activated - not regulated 2 mg/m続
American Industrial Hygiene Association (AIHA)
Ingredients considered according exceed the following cutoffs
Very Toxic (T+) >= 0.1% Toxic (T) >= 3.0%
R50 >= 0.25% Corrosive (C) >= 5.0%
R51 >= 2.5%
else >= 10%
where percentage is percentage of ingredient found in the mixture
Section 7 - HANDLING AND STORAGE
PROCEDURE FOR HANDLING
NOTE: Wet, activated carbon removes oxygen from the air thus producing a severe
hazard to workers inside carbon vessels and in enclosed or confined spaces where
activated carbons might accumulate. Before entry to such areas, sampling and
test procedures for low oxygen levels should be undertaken; control conditions
should be established to ensure the availability of adequate oxygen supply.
- Avoid all personal contact, including inhalation.
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 6 of 12
Section 7 - HANDLING AND STORAGE
- Wear protective clothing when risk of exposure occurs.
- Use in a well-ventilated area.
- Prevent concentration in hollows and sumps.
- DO NOT enter confined spaces until atmosphere has been checked.
- DO NOT allow material to contact humans, exposed food or food utensils.
- Avoid contact with incompatible materials.
- When handling, DO NOT eat, drink or smoke.
- Keep containers securely sealed when not in use.
- Avoid physical damage to containers.
- Always wash hands with soap and water after handling.
- Work clothes should be laundered separately.
- Launder contaminated clothing before re-use.
- Use good occupational work practice.
- Observe manufacturer's storing and handling recommendations.
- Atmosphere should be regularly checked against established exposure standards
to ensure safe working conditions are maintained.
RECOMMENDED STORAGE METHODS
- Polyethylene or polypropylene container.
- Check all containers are clearly labelled and free from leaks.
STORAGE REQUIREMENTS
Observe manufacturer's storing and handling recommendations.
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE CONTROLS
Source Material TWA TWA STEL STEL Peak Peak
ppm mg/m続 ppm mg/m続 ppm mg/m続
_________________________ ________________ _____ _____ _____ _____ _____ _____
US - Idaho - Toxic and Silicates (less 15
Hazardous Substances - than 1%
Mineral Dust crystalline
silica):
Graphite
(natural)
US - California Graphite, -- 5
Permissible Exposure synthetic
Limits for Chemical Respirable
Contaminants fraction(n)
US - Vermont Permissible Graphite, 5
Exposure Limits Table synthetic -
Z-1-A Final Rule Limits Respirable
for Air Contaminants Fraction
US - Vermont Permissible Graphite, 10
Exposure Limits Table synthetic -
Z-1-A Final Rule Limits Total dust
for Air Contaminants
Canada - Yukon Graphite (See
Permissible (synthetic) Table
Concentrations for 11)
Airborne Contaminant
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 7 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Source Material TWA TWA STEL STEL Peak Peak
ppm mg/m続 ppm mg/m続 ppm mg/m続
_________________________ ________________ _____ _____ _____ _____ _____ _____
Substances
US - California Graphite, -- 10
Permissible Exposure synthetic Total
Limits for Chemical dust
Contaminants
US - Minnesota Graphite, 10
Permissible Exposure synthetic -
Limits (PELs) Total dust
No data available: zeolites as (CAS: 1318-02-1) / (CAS: 37305-72-9) / (CAS: 50809-51-3) / (CAS: 52349-29-8) / (CA
No data available: water as (CAS: 7732-18-5)
No data for Ammo-Carb.
EXPOSURE STANDARDS FOR MIXTURE
"Worst Case" computer-aided prediction of spray/ mist or fume/ dust components
and concentration:
"Worst Case" computer-aided prediction of spray/ mist or fume/ dust components
and concentration:
Composite Exposure Standard for Mixture (TWA) :3.7221 mg/m続.
"Worst Case" computer-aided prediction of spray/ mist or fume/ dust components
and concentration:
Composite Exposure Standard for Mixture (TWA) (mg/m続):
Operations which produce a spray/mist or fume/dust, introduce particulates to
the breathing zone.
If the breathing zone concentration of ANY of the components listed below is
exceeded, "Worst Case" considerations deem the individual to be overexposed.
Component Breathing Zone ppm Breathing Zone mg/m続 Mixture Conc (%).
Component Breathing Zone Mixture Conc
(mg/m続) (%)
carbon, steam activated - not reg 2.9777
20.0
INGREDIENT DATA
ZEOLITES:
Dusts not otherwise classified, as inspirable dust;
ES TWA: 10 mg/m続.
Particulate (insoluble or poorly soluble *) Not Otherwise Specified (P.N.O.C)
TLV TWA: 10 mg/m続 Inhalable particulate
TLV TWA: 3 mg/m続 Respirable particulate
OEL-Sweden, United Kingdom: 10 mg/m続 total dust, 5 mg/m続 respirable dust
These "dusts" have little adverse effect on the lungs and do not produce toxic
effects or organic disease. Although there is no dust which does not evoke some
cellular response at sufficiently high concentrations, the cellular response
caused by P.N.O.C.s has the following characteristics:
- the architecture of the air spaces remain intact,
- scar tissue (collagen) is not synthesised to any degree,
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 8 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
- tissue reaction is potentially reversible.
Extensive concentrations of P.N.O.C.s may:
- seriously reduce visibility,
- cause unpleasant deposits in the eyes, ears and nasal passages,
- contribute to skin or mucous membrane injury by chemical or mechanical action,
per se, or by the rigorous skin cleansing procedures necessary for their
removal. [ACGIH]
This limit does not apply:
- to brief exposures to higher concentrations
- nor does it apply to those substances that may cause physiological impairment
at lower concentrations but for which a TLV has as yet to be determined.
This exposure standard applies to particles which
- are insoluble or poorly soluble* in water or, preferably, in aqueous lung
fluid (if data is available) and
- have a low toxicity (i.e.. are not cytotoxic, genotoxic, or otherwise
chemically reactive with lung tissue, and do not emit ionizing radiation, cause
immune sensitization, or cause toxic effects other than by inflammation or by a
mechanism of lung overload)
* Notice of intended change.
CARBON, STEAM ACTIVATED - NOT REGULATED:
for carbon blacks of mineral origin
TLV TWA: 3.5 mg/m続 A4
NOTE: This substance has been classified by the ACGIH as A4 NOT classifiable as
causing Cancer in humans.
ES TWA: 3 mg/m続
Carbon blacks of vegetable origin not listed.
WATER:
No exposure limits set by NOHSC or ACGIH.
PERSONAL PROTECTION
EYE
- Safety glasses with side shields.
- Chemical goggles.
- Contact lenses pose a special hazard; soft lenses may absorb irritants and all
lenses concentrate them. DO NOT wear contact lenses.
HANDS/FEET
Wear chemical protective gloves, eg. PVC.
Wear safety footwear or safety gumboots, eg. Rubber.
OTHER
- Overalls.
- P.V.C. apron.
- Barrier cream.
- Skin cleansing cream.
- Eye wash unit.
RESPIRATOR
Protection Half-Face Full-Face Powered Air
Factor Respirator Respirator Respirator
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 9 of 12
Section 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
10 x PEL P1 - PAPR-P1
Air-line* - -
50 x PEL Air-line** P2 PAPR-P2
100 x PEL - P3 -
Air-line* -
100+ x PEL - Air-line** PAPR-P3
* - Negative pressure demand ** - Continuous flow
Explanation of Respirator Codes:
Class 1 low to medium absorption capacity filters.
Class 2 medium absorption capacity filters.
Class 3 high absorption capacity filters.
PAPR Powered Air Purifying Respirator (positive pressure) cartridge.
Type A for use against certain organic gases and vapors.
Type AX for use against low boiling point organic compounds (less than
65ºC).
Type B for use against certain inorganic gases and other acid gases and vapors.
Type E for use against sulfur dioxide and other acid gases and vapors.
Type K for use against ammonia and organic ammonia derivatives
Class P1 intended for use against mechanically generated particulates of sizes
most commonly encountered in industry, e.g. asbestos, silica.
Class P2 intended for use against both mechanically and thermally generated
particulates, e.g. metal fume.
Class P3 intended for use against all particulates containing highly toxic
materials, e.g. beryllium.
The local concentration of material, quantity and
conditions of use determine the type of personal
protective equipment required.
Use appropriate NIOSH-certified respirator based on informed professional
judgement. In conditions where no reasonable estimate of exposure can be
made, assume the exposure is in a concentration IDLH and use NIOSH-certified
full face pressure demand SCBA with a minimum service life of 30 minutes, or
a combination full facepiece pressure demand SAR with auxiliary self-contained
air supply. Respirators provided only for escape from IDLH atmospheres shall be
NIOSH-certified for escape from the atmosphere in which they will be used.
ENGINEERING CONTROLS
- Local exhaust ventilation is required where solids are handled as powders or
crystals; even when particulates are relatively large, a certain proportion will
be powdered by mutual friction.
- If in spite of local exhaust an adverse concentration of the substance in air
could occur, respiratory protection should be considered.
Such protection might consist of:
(a): particle dust respirators, if necessary, combined with an absorption
cartridge;
(b): filter respirators with absorption cartridge or canister of the right type;
(c): fresh-air hoods or masks
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL PROPERTIES
Does not mix with water.
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 10 of 12
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
Molecular Weight: Not Applicable Boiling Range (C): Not Applicable
Melting Range (C): Not Available Specific Gravity (water=1): Not Available
Solubility in water (g/L): Immiscible pH (as supplied): Not Applicable
pH (1% solution): Not Applicable Vapor Pressure (kPa): Not Applicable
Volatile Component (%vol): Not Applicable Evaporation Rate: Not Applicable
Relative Vapor Density (air=1): Not Applicable Flash Point (C): Not Applicable
Lower Explosive Limit (%): Not Applicable Upper Explosive Limit (%): Not Applicable
Autoignition Temp (C): Not Applicable Decomposition Temp (属C): Not Available
State: Divided Solid
APPEARANCE
Black crystalline sand-like granules; insoluble in water.
Section 10 - CHEMICAL STABILITY AND REACTIVITY INFORMATION
CONDITIONS CONTRIBUTING TO INSTABILITY
- Presence of incompatible materials.
- Product is considered stable.
- Hazardous polymerization will not occur.
STORAGE INCOMPATIBILITY
Activated carbon, when exposed to air, represents a potential fire hazard due to
a high surface area and adsorptive capacity. Freshly prepared material may
ignite spontaneously in the presence of air especially at high humidity.
Spontaneous combustion in air may occur at 90-100 deg. C. The presence of
moisture in air facilitates the ignition. Drying oils and oxidising oils promote
spontaneous heating and ignition; contamination with these must be avoided.
Unsaturated drying oils (linseed oil etc.) may ignite following adsorption owing
to an enormous increase in the surface area of oil exposed to air; the rate of
oxidation may also be catalysed by metallic impurities in the carbon. A similar,
but slower effect occurs on fibrous materials such as cotton waste. Spontaneous
heating of activated carbon is related to the composition and method of
preparation of the activated carbon. Free radicals, present in charcoal, are
responsible for autoignition. Self-heating and autoignition may also result from
adsorption of various vapours and gases (especially oxygen). For example,
activated carbon auto- ignites in flowing air at 452-518 deg. C.; when the base,
triethylene-diamine, is adsorbed on the carbon (5%) the autoignition temperature
is reduced to 230-260 deg. C.. An exotherm is produced at 230-260 deg. C., at
high flow rates of air, although ignition did not occur until 500 deg. C..
Mixtures of sodium borohydride with activated carbons, in air, promote the
oxidation of sodium borohydride, producing a self-heating reaction that may
result in the ignition of charcoal and in the production of hydrogen through
thermal decomposition of the borohydride.
Avoid reaction with oxidizing agents.
Section 11 - TOXICOLOGICAL INFORMATION
Ammo-Carb
Not available. Refer to individual constituents.
unless otherwise specified data extracted from RTECS - Register of Toxic Effects
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 11 of 12
Section 11 - TOXICOLOGICAL INFORMATION
of Chemical Substances
ZEOLITES:
~TOXICITY FIGURE
Oral~rat~LD50~>5110~mg/kg
Dermal~rabbit~LD50~>2000~mg/kg
Inhalation~-~LC50~>18.3~mg/l/1hr
~OTHER
for sodium aluminosilicate, zeolite A:
Skin (rabbit): non-irritating
Eye (rabbit): slight
[Grace]
CARBON, STEAM ACTIVATED - NOT REGULATED:
No data of toxicological significance identified in literature search.
WATER:
No significant acute toxicological data identified in literature search.
Section 12 - ECOLOGICAL INFORMATION
Marine Pollutant:Not Determined
DO NOT discharge into sewer or waterways.
Refer to data for ingredients, which follows:
ZEOLITES:
for sodium aluminosilicate, zeolite A
Fish toxicity (Brachidario rerio) 96H LC50: 1800 mg/l
Aquatic toxicity (Dapnia magna) 24H EC50: 2808 mg/l
Algal toxicity (Scenedesmus subspecies) 96H NOEC: 10 mg/l
Bacterial toxicity (Pseudomonas putida): 330 mg/l, initial inhibition of
cell multiplication
[Grace]
Section 13 - DISPOSAL CONSIDERATIONS
Disposal Instructions
All waste must be handled in accordance with local, state and federal
regulations.
- Recycle wherever possible.
- Consult manufacturer for recycling options or consult Waste Management
Authority for disposal if no suitable treatment or disposal facility can be
identified.
- Dispose of by: Burial in a licensed land-fill or Incineration in a licensed
apparatus (after admixture with suitable combustible material)
- Decontaminate empty containers. Observe all label safeguards until containers
are cleaned and destroyed.
continued...
AMMO-CARB
Chemwatch Material Safety Data Sheet
Issue Date: 22-Dec-2005 CHEMWATCH 4658-39
CD 2005/4 Page 12 of 12
Section 14 - TRANSPORTATION INFORMATION
NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS:UN,IATA,IMDG
Section 15 - REGULATORY INFORMATION
RISK
Risk Codes Risk Phrases
R07 May cause fire.
REGULATIONS
No regulations applicable
carbon, steam activated - not regulated (CAS: 7440-44-0) is found on the
following regulatory lists;
Canada Domestic Substances List (DSL)
US - Minnesota Hazardous Substance List
US EPA High Production Volume Program Chemical List
US Toxic Substances Control Act (TSCA)
water (CAS: 7732-18-5) is found on the following regulatory lists;
Canada Domestic Substances List (DSL)
US Toxic Substances Control Act (TSCA)
No data available for zeolites as CAS: 1318-02-1, CAS: 37305-72-9, CAS:
50809-51-3, CAS: 52349-29-8, CAS: 53025-48-2, CAS: 53060-43-8, CAS: 53569-61-2,
CAS: 53789-62-1, CAS: 54693-40-2, CAS: 54824-24-7, CAS: 56747-83-2, CAS:
61710-45-0, CAS: 75216-11-4, CAS: 76774-74-8, CAS: 85117-23-3.
Section 16 - OTHER INFORMATION
LIMITED EVIDENCE
Cumulative effects may result following exposure*.
May produce discomfort of the eyes and respiratory tract*.
Limited evidence of a carcinogenic effect*.
* (limited evidence).
Reasonable care has been taken in the preparation of this information, but the
author makes no warranty of merchantability or any other warranty, expressed or
implied, with respect to this information. The author makes no representations
and assumes no liability for any direct, incidental or consequential damages
resulting from its use. For additional technical information please call our
toxicology department on +800 CHEMCALL.
Issue Date: 22-Dec-2005
Print Date: 22-Dec-2005
This document is copyright. Apart from any fair dealing for the purposes of
private study, research, review or criticism, as permitted under the Copyright
Act, no part may be reproduced by any process without written permission from
CHEMWATCH. TEL (+61 3) 9572 4700.
|