MSDS NAME:774571 HMF 2603D/77-3 49
NIIN:00F048010
MSDS Number: BZDTP
=== Responsible Party ===
Company:FIBERITE CORP SUB OF BEATRICE FOODS
Address:501 W 3RD ST
City:WINONA
State:MN
ZIP:55987-2854
Country:US
Info Phone Num:507-452-8092
Emergency Phone Num:507-452-8051
CAGE:GO121
=== Contractor Identification ===
Company:FIBERITE CORP SUB OF BEATRICE FOODS
Address:501 W 3RD STREET
Box:City:WINONA
State:MN
ZIP:55987-2854
Country:US
Phone:507-452-8082/507-452-8092
CAGE:07314
Company:FIBERITE CORP SUB OF BEATRICE FOODS
Address:501 W 3RD ST
City:WINONA
State:MN
ZIP:55987-2854
Country:US
Phone:507-454-3611
CAGE:GO121
============= Composition/Information on Ingredients =============
Name:CARBON/GRAPHITE FIBERS
Fraction by Wt: 40-70%
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:CARBON/GRAPHITE FIBERS-EYES/SKIN: MAY
CAUSE IRRITATION & MECHANICAL DERMATITIS, POSSIBLE ALLERGIC
REACTION TO SIZING. INHALATION: RESPIRATORY IRRITATION DUE TO
AIRBORNE FIBERS.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:CARBON/GRAPHIC FIBERS: IRRITATION, ITCHING.
======================= First Aid Measures =======================
First Aid:INHALATION: REMOVE TO FRESH AIR. GIVE OXYGEN/MOUTH TO MOUTH
IF NECESSARY. EYES: IRRIGATE W/WATER FOR A MINIMUM OF 15 MINS.
SKIN: WASH THOROUGHLY W/SOAP & WATER. OBTAIN MEDICAL ATTENTION IN
ALL CASES.
===================== Fire Fighting Measures =====================
Extinguishing Media:CO2, FOAM, DRY CHEMICAL, WATER
Fire Fighting Procedures:DISSIPATE HEAT BY SPREADING MATERIAL APART &
DOUSING W/WATER.
Unusual Fire/Explosion Hazard:CONTAINS EMISSIONS USING LOCAL EXHAUST.
Spill Release Procedures:CONTAMINATED MATERIAL SHOULD BE PICKED UP &
DISPOSED OF PROPERLY.
====================== Handling and Storage ======================
Handling and Storage Precautions:STORE AT/BELOW 0F. WHEN PROCESSING AT
ELEVATED TEMPS, PROVIDE ADEQUATE VENTILATION TO CONTROL PROCESSING
VAPORS & FUMES.
Other Precautions:USE GLOVES WHEN HANDLING UNCURED MATERIAL IS STRONGLY
RECOMMENDED. AVOID SKIN CONTACT! AVOID HEATING MATERIAL IN BULK.
CURING SHOULD ONLY BE DONE IN WELL-VENTILATED/CLOSED SYSTEMS.
PROTECT ELECTRICAL EQUIPMENT AGAINST INFILTRATION.
Respiratory Protection:USE NIOSH APPROVED RESPIRATOR IF EXPOSURE LIMITS
ARE EXCEEDED. PROVIDE NIOSH APPROVED RESPIRATORS TO MINIMIZE
EXPOSURE TO GAS, VAPORS/FUMES RELEASED DURING LAY UP/MOLDING
OPERATIONS.
Ventilation:GOOD GENERAL/LOCAL EXHAUST: TO CONTROL AIRBORNE LEVELS <
EXPOSURE LIMITS, WHERE GRINDING/HEATING OPERATIONS OCCUR.
Protective Gloves:IMPERVIOUS
Eye Protection:SAFETY GLASSES/FACE SHIELD
Other Protective Equipment:CLEAN BODY COVERING CLOTHING TO MINIMIZE
EXPOSURE.
Supplemental Safety and Health
Waste Disposal Methods:DISPOSE OF IAW/FEDERAL, STATE & LOCAL
REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.