=====================  Product Identification  =====================

MSDS NAME:900660622, DEXTER EPOXY PATCH KIT 0151 CLEAR (SUPDAT)
NIIN:01-091-9671
Kit Part:Y
MSDS Number: CDKKK
=== Responsible Party ===
Company:AT&T
Address:ONE OAK WAY
City:BERKELEY HEIGHTS
State:NJ
ZIP:07922-2727
Country:US
Info Phone Num:908-204-8243
Emergency Phone Num:800-424-9300(CHEMTREC)
CAGE:ATTEL
=== Contractor Identification ===
Company:AT AND T NETWORK SYSTEMS
Address:1 OAK WAY
Box:City:BERKLEY HEIGHTS
State:NJ
ZIP:07922
Country:US
CAGE:0PWA9
Company:AT&T
Address:ONE OAK WAY
Box:City:BERKELEY HEIGHTS
State:NJ
ZIP:07922-2727
Country:US
Phone:908-204-8243
CAGE:ATTEL

=============  Composition/Information on Ingredients  =============

Name:TRIETHYLENETETRAMINE
CAS:112-24-3
RTECS #:YE6650000
OSHA PEL:N/K 
ACGIH TLV:N/K 

Name:SILICA GEL; (SILICA, AMORPHOUS)
CAS:112945-52-5
RTECS #:VV7310000
OSHA PEL:6 MG/M3
ACGIH TLV:10 MG/M3

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:NO	Skin:YES  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:ACUTE:IRRITATING TO SKIN AND EYES.
    CHRONIC:EXPOSURE MAY CAUSE SKIN SENSITIZATION. THE TOXICOLOGICAL
    PROPERTIES OF THIS PRODUCT MAY NOT BE FULLY INVESTIGATED.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

Eyes:FLUSH W/WARM WATER FOR AT LEAST 15 MINUTES. SEE MD.
    SKIN:FLUSH W/PLENTY OF WATER. WASH THOROUGHLY W/SOAP & WATER, HAND
    CLEANER OR RUBBING ALCOHOL. DO NOT USE OTHER SOLVENTS TO REMOVE
    MATERIAL FRO M SKIN. IF IRRITATION PERSISTS SEE MD. REMOVE
    CONTAMINATED CLOTHING & LAUNDER BEFORE REUSE. INHAL:REMOVE TO FRESH
    AIR. INGEST:OBTAIN MEDICAL ATTENTION.

=====================  Fire Fighting Measures  =====================

Flash Point:200F,93C
Lower Limits:0.4%
Upper Limits:1.3%
Extinguishing Media:DRY CHEMICAL OR HALON FIRE EXTINGUISHERS, WATER
    SPRAY OR FOG, & FOAM.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
    EQUIPMENT .
Unusual Fire/Explosion Hazard:DENSE SMOKE & TOXIC GASES MAY BE PRODUCED
    UPON COMBUSTION.

==================  Accidental Release Measures  ==================

Spill Release Procedures:SCRAPE UP & TRANSFER TO METAL CONTAINER FOR
    DISPOSAL. USE A RAG OR PAPER TOWEL W/DETERGENT TO WIPE & CLEAN OFF
    REMAINING RESIDUE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE IN A COOL, DRY PLACE. DO NOT MIX
    IN BATCHES OF GREATER THAN ONE POUND TOTAL. FOLLOW RECOMMENDED
    CURING PROCEDURES.
Other Precautions:SILICA PARTICLES IN THIS PRODUCT ARE IN WETTED
    MATERIAL SO AIRBORNE EXPOSURE WILL NOT OCCUR UNLESS CURED MATERIAL
    IS SUBSEQUENTLY GROUND, MACHINED OR SANDED. CORROSIVE, SENSITIZER.
    SLIGHTLY COMBUSTIBL E.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NIOSH APPROVED RESPIRATOR APPROPRIATE FOR
    EXPOSURE OF CONCERN . NOT REQUIRED IF VENTILATION IS SUFFICIENT.
Ventilation:LOCAL EXHAUST VENTILATION IS RECOMMENDED. GENERAL
    VENTILATION MAY BE ACCEPTABLE.
Protective Gloves:IMPERVIOUS PLASTIC OR RUBBER GLOVES.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
    ANSI DESIGN CRITERIA . OTHER CLOTHING &/OR EQUIPMENT AS (SUPP DATA)
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
MFR'S TRADE NAME/PART NO:HARDENER. CNDTNS(POLYM):FAILURE TO OBSERVE
    CAUTIONS MAY RESULT IN EXCESSIVE HEAT BUILD-UP W/RELEASE OF TOXIC
    GASES. OTHER PROT EQUIP:NEEDED TO PROTECT SKIN & CLOTHING.

==================  Physical/Chemical Properties  ==================

Boiling Pt:B.P. Text:531F,277C
Vapor Pres:<0.01
Vapor Density:>1
Spec Gravity:0.98
Solubility in Water:20%
Appearance and Odor:AMBER LIQUID W/SLIGHT AMMONIA LIKE ODOR.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS ACIDS OR MINERAL ACIDS.
Stability Condition to Avoid:NONE.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
    OXIDES OF NITROGEN, ALDEHYDES, ORGANIC ACIDS & UNDETERMINED
    ORGANICS.
Conditions to Avoid Polymerization:AVOID MIXING RESIN & CURING AGENT IN
    BATCHES >1 LB TOTAL. DO NOT HEAT MATL UNLESS CURING SURFS TO BE
    BONDED. (SUPP DATA)

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF I/A/W LOCAL, STATE & FEDERAL RULES &
    REGULATIONS. APPROPRIATE DISPOSAL METHODS MAY INCLUDE LANDFILL OR
    INCINERATION.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***