3M GENERAL OFFICES -- JET MELT, 3792-LM-PG
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: BVXKX
MSDS NAME: JET MELT, 3792-LM-PG
Responsible Party
Name: 3M GENERAL OFFICES
Address: 3M CENTER
City: ST PAUL MN 55144-1000
Info Phone: 612-733-1110
Emergency Phone Number: 612-733-1110
Published: Y
=======================================================
Contractor Summary
=======================================================
Name: MINNESOTA MINING AND MFG CO, DBA 3M
Address: 3M CENTER BLDG 224-5S-04
City: SAINT PAUL MN 55144-1000
Phone: 866-556 5712 / 612-733-1110
Name: MINNESOTA MINING AND MFG CO ENGINEERING DOCUMENT SYSTEMS DIV
Address: 3M CTR
City: SAINT PAUL MN 55144-1000
Phone: 612-737-4114
=======================================================
Ingredients
=======================================================
Cas: 24937-78-8
Name: ACETIC ACID ETHENYL ESTER POLYMER WITH ETHENE; (ETHLENE-VINYL ACETATE
POLYMER)
% Wt: 60-70
OSHA PEL: N/K (FP N)
ACGIH TLV: N/K (FP N)
------------------------------
Cas: 68132-00-3
Name: HYDROCARBON RESIN
% Wt: 30-40
OSHA PEL: N/K (FP N)
ACGIH TLV: N/K (FP N)
-----------------------------
Name: SUPDAT:CNDTNS. THESE PROCESS RELS MAY PRDCE IRRIT/ANY OF HLTH EFTS LISTED
WHEN EMISSIONS ARE PRESENT AT ELEVATED
-----------------------------
Name: ING 3:CONCS. USE W/APPROP LOC EXHST VENT. NOTE:LAB ANIMALS WERE CONDUCTED
TO CHARACT VOLATS RELS DURING JET-MELT
-----------------------------
Name: ING 4:USE. AIR SAMPLES WERE COLLECTED FROM HEAD SPACE OF ADHESIVE &
FROM SIMULATED BRTHG ZONE OF POLYGUN USER
-----------------------------
Name: ING 5:DURING APPLICATION. ALTHOUGH ACETIC ACID & ACROLEIN WERE
MEASURED IN PROD'S HEAD SPACE, CHEMS WERE NOT
-----------------------------
Name: ING 6:DETECTED IN BRTHG ZONE AIR SAMPLES (I.E., CHEM CONCS WERE BELOW
LOWER LIMS OF ANALYTICAL DETECTION). THESE
-----------------------------
Name: ING 7:RSLTS INDICATE VERY LOW INHAL HAZ WHEN NORMAL INDUS HYGIENE
PRACTICES ARE USED. HOWEVER, CUSTOMER
-----------------------------
Name: ING 8:CORRESPONDENCE INDICATE THAT EYE & UPPER RESP SYS IRRIT MAY
OCCUR. FOR THIS REASON, PROD SHOULD BE USED IN
-----------------------------
Name: ING 9:WELL VENTILATED AREA.
=======================================================
Health Hazards Data
=======================================================
LD50 LC50 Mixture: NONE SPECIFIED BY MANUFACTURER.
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: YES
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Effects of Exposure: YE CONT:VAPS FROM HEATED MATL MAY CAUSE IRRIT. SINGLE
EXPOS MAY CAUSE MILD IRRIT: SIGNS/SYMPS CAN INCL REDNESS, SWELL, PAIN &
TEARING. SKIN: BURNS(FROM CONT W/MOLTEN MATL: SIGNS/SYMPS MAY INCL BURNING
PAIN, RED & SWOLLEN SKIN & BLISTERS. MILD IRRIT: SIGNS/SYMPS CAN INCL
REDNESS, SWELL & ITCH. INHAL: (EFTS OF OVEREXP)
Explanation Of Carcinogenicity: NOT RELEVANT
Signs And Symptions Of Overexposure: HLTH HAZ:IRRIT(UPPER RESP): SIGNS/SYMPS
CAN INCL SORENESS OF NOSE & THROAT, COUGH & SNEEZING. VAPS OF HEATED
MATL MAY CAUSE RESP SYS IRRIT. INGEST:NOT LIKELY RTE OF EXPOS TO THIS PROD.
IRRIT OF GI TIS S: SIGNS/SYMPS CAN INCL PAIN, VOMITUS, ABDOM TENDERNESS,
NAUS, BLOOD IN VOMITUS & BLOOD IN FECES. OTHER HLTH HAZ(SUPDAT)
Medical Cond Aggravated By Exposure: NONE SPECIFIED BY MANUFACTURER.
First Aid: EYE:IMMEDIATELY FLUSH W/LARGE AMOUNTS OF WATER FOR AT LEAST 15
MINUTES. GET IMMEDIATE MEDICAL ATTENTION. SKIN:IMMEDIATELY FLUSH AFFECTED
AREA W/LARGE AMOUNTS OF WATER & COVER W/CLEAN DRESSING. DO NOT ATTEMPT
TO REMOVE ADHESIVE. HAVE BURN TREATED BY MD. INHAL:REMOVE PERSON TO FRESH
AIR. IF SIGNS/SYMPTOMS CONTINUE, CALL MD. INGEST:DO NOT INDUCE VOMITING.
DRINK 2 GLASSES OF WATER. CALL MD.
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: OBSERVE PRECAUTIONS FROM OTHER SECTIONS. COLLECT
SPILLED MATERIAL.
Neutralizing Agent: NONE SPECIFIED BY MANUFACTURER.
Waste Disposal Methods: DISPOSE OF WASTE PRODUCT IN A SANITARY LANDFILL. SINCE
REGULATIONS VARY, CONSULT APPLICABLE LOCAL, STATE & FEDERAL REGULATIONS
OR AUTHORITIES BEFORE DISPOSAL.
Handling And Storage Precautions: AVOID EYE CONTACT W/VAPOR, SPRAY OR MIST.
AVOID SKIN CONTACT W/HOT ADHESIVE & APPLICATOR TIP. AVOID PROLONGED
BREATHING OF VAPORS. DO NOT INGEST.
Other Precautions: KEEP OUT OF REACH OF CHILDREN.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Flash Point Method: COC
Flash Point Text: >450F,>232C
Extinguishing Media: WATER SPRAY, CARBON DIOXIDE, DRY CHEMICAL, FOAM.
Fire Fighting Procedures: USE NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT (FP N).
Unusual Fire/Explosion Hazard: NO UNUSUAL FIRE OR EXPLOSION HAZARDS ARE
ANTICIPATED.
=======================================================
Control Measures
=======================================================
Respiratory Protection: NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR EXPOSURE
OF CONCERN (FP N).
Ventilation: PROVIDE APPROPRIATE LOCAL EXHAUST FOR MOLTEN OR EXTRUDED MATERIAL.
USE IN A WELL-VENTILATED AREA.
Protective Gloves: APPROPRIATE GLOVES, SUCH AS NOMEX.
Eye Protection: UNVENTED GOGGLES.
Other Protective Equipment: NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices: NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health: APPEAR/ODOR:PUNGENT RESINOUS ODOR). EFTS OF
OVEREXP:INFO:EXPOS TO THIS MATL IN NORMAL STOR & HNDLG HAS NOT BEEN
REPORTED TO CAUSE SIGNIFICANT ADVERSE HLTH EFTS. HOWEVER, UNDER NORMAL
PROCESSING CNDTNS , E.G., GRINDING/HEATING, THIS PROD MAYRELS FUMES &
VAPS OF VARIABLE COMPOSITION BASED ON SPECIFIC PROCESS
=======================================================
Physical/Chemical Properties
=======================================================
HCC: N1
Spec Gravity: 1.01 (H*2O=1)
Solubility in Water: NIL
Appearance and Odor: WAXY SOLID, TRANSLUCENT, SOLID ADHESIVE IN RODS; ODORLESS.
(WHEN MOLTEN:(SUPDAT
Percent Volatiles by Volume: 0 (WT)
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products: CARBON MONOXIDE & CARBON DIOXIDE. TOXIC
VAPORS, GASES OR PARTICULATES.
Hazardous Polymerization Indicator: NO
Conditions To Avoid Polymerization: NOT RELEVANT
=======================================================
Toxicological Information
=======================================================
=======================================================
Ecological Information
=======================================================
=======================================================
MSDS Transport Information
=======================================================
=======================================================
Regulatory Information
=======================================================
=======================================================
Other Information
=======================================================
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: JET MELT, 3792-LM-PG
Company: MINNESOTA MINING AND MFG CO ENGINEERING DOCUMENT SYSTEMS DIV
Street: 3M CTR
City: SAINT PAUL MN
Zipcode: 55144-1000
Health Emergency Phone: 612-733-1110
Label Required IND: Y
Date Of Label Review: 10/13/1994
Status Code: C
Label Date: 10/13/1994
Origination Code: G
Eye Protection IND: YES
Skin Protection IND: YES
Signal Word: CAUTION
Respiratory Protection IND: YES
Health Hazard: Slight
Contact Hazard: Slight
Fire Hazard: Slight
Reactivity Hazard: None
Hazard And Precautions: COMBUSTIBLE. ACUTE:EYE CONTACT:VAPORS FROM HEATED
MATERIAL MAY CAUSE IRRITATION. SINGLE EXPOSURE MAY CAUSE MILD IRRITATION:
SIGNS OR SYMPTOMS CAN INCLUDE REDNESS, SWELLING, PAIN & TEARING.
SKIN:BURNS (FROM CONTACT W/MOLTEN MATERIAL: SIGNS OR SYMPTOMS MAY INCLUDE
BURNING PAIN, RED & SWOLLEN SKIN & BLISTERS. MILD IRRITATION: SIGNS
OR SYMPTOMS CAN INCLUDE REDNESS, SWELLING & ITCHING. INHAL:IRRITATION .
INGEST:GASTROINTESTINAL IRRITATION. CHRONIC:NONE LISTED BY MANUFACTURER.
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
4193, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
5193, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
6193, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
7193, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
8193, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
2190, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
3190, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
4190, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
5190, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
6190, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
7190, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
8190, SCOTCH BRAND V.C.I. CORR INHIBITING (SUPDAT)
| 9002-88-4
7632-00-0
112945-52-5 |
|
WATER PROOFING SOLUTION
| 108-88-3
78-93-3
64475-85-0
9010-98-4
22708-90-3
1333-86-4
28085-50-1
1330-20-7 |
|
WATER BASED INK FOR THE 4697 PRINTER, 016-0974-00
| |
|
WATER BASED INK FOR THE 4697 PRINTER, 016-0975-00
| |
|
WATER BASED INK FOR THE 4697 PRINTER, 016-0976-00
| |
|
WATER BASED INK FOR THE 4697 PRINTER, 016-0977-00
| |
|
INK CARTRIDGE, BJI-642, F47-0011-000
| |
|
INK CARTRIDGE BLACK BC-02, F45-0241-400
| |
|
MAZIN SR
| |
|
OKIDATA 400/800 REPLACEMENT TONER
| |
|
HENCO-SOLV 311 (10-763)
| |
|
SB1223 EPOXY HARDENER
| |
|
DEGREASEALL DG7S-6
| |
|
JOINTING COMPOUND JC5A, 823E508
| |
|
JET MELT, 3792-LM-PG
| 24937-78-8
68132-00-3 |
|
JET MELT, 3792-LM-TC
| 24937-78-8
68132-00-3 |
|
JET MELT, 3792-LM-Q (1PC)
| 24937-78-8
68132-00-3 |
|
SCOTCHCAST EXPANDABLE SEALANT FOR 4411 REHAB KIT PT A
| |
|
SCOTCHCAST EXPANDABLE SEALANT FOR 4411 REHAB KIT PT B
| 25723-16-4
25322-69-4
7732-18-5
98-94-2 |
|
SCOTCHCAST EXPANDABLE SEALANT FOR 4416 REHAB KIT PT A
| |
|
SCOTCHCAST EXPANDABLE SEALANT FOR 4416 REHAB KIT PT B
| 25723-16-4
25322-69-4
7732-18-5
98-94-2 |
|
SCOTCHCAST EXPANDABLE SEALANT FOR K&B REHAB KIT PT A
| |
|
SCOTCHCAST EXPANDABLE SEALANT FOR K&B REHAB KIT PT B
| 25723-16-4
25322-69-4
7732-18-5
98-94-2 |
|
708GC, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
700GC, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
55GC, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
M50, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
716GC, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
1200, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
M50P, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
M40, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
M-20-600, MAGIC LENS CLEANING ANTI-FOGGING (SUPP DATA)
| |
|
WASH N'WEAR LSG MIDTONE BASE INTERIOR PAINT, 5842
| |
|
ACRY-GLO SG H&T MIDTONE BASE EXTERIOR PAINT, 5882
| |
|
SELFLOC 1425B
| |
|
DIESEL-MATE, 0318
| |
|
3500 SERIES, SPILFYTER FOR HYDROCARBON (SUPDAT)
| |
|
CUTTING OIL FRESHENER
| 7732-18-5 |
|
RPC-060 DECACHLOROBIPHENYL
| 2051-24-3 |
|
|