iron oxide water;(deionized water) ethylene glycol 2-4-pentanediol,2-methyl;(hexylene glycol) film formers, resins & additives supp data:swelling are conditions associated with excessive first aid proc:material, persistent skin/eye irritation or vent:limits, lel below stated limit, and to remove decomp
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INGEST:HARMFUL/FATAL. EYE:CAUSES
SEVERE IRRITATION. SKIN:CAUSES PRIMARY IRRITATION. MAY BE ABSORBED
THROUGH SKIN. INHAL:VAPOR AND SPRAY MIST MAY BE HARMFUL IF INHALED.
VAPOR GENERATED AT ELEVATED TEMP S IRRITATES EYES, NOSE & THROAT.
VAP IRRITATES EYES/NOSE/THROAT. CHRONIC:AVOID LONG TERM & RPTD
CONT. (EFTS OF OVEREXP).
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ:CNTNS ETHYLENE GLYCOL WHICH MAY CAUSE
KIDNEY & LIVER DMG & WHICH HAS BEEN SHOWN TO CAUSE BIRTH DEFECTS IN
LAB ANIMALS. NO EVIDENCE OF THESE EFTS HAS BEEN FOUND IN HUMANS.
CNTNS HEXYLENE GLYCO L WHICH HAS CAUSED ADVERSE KIDNEY & LIVER EFTS
IN LAB ANIMALS. THERE IS NO EVIDENCE OF THESE EFTS IN HUMANS. (SUPP
DATA)
Medical Cond Aggravated by Exposure:NOT APPLICABLE.
======================= First Aid Measures =======================
First Aid:INGEST:DO NOT INDUCE VOMIT. EYE:FLUSH IMMED W/PLENTY OF WATER
FOR AT LEAST 15 MINS. SKIN:FLUSH IMMED W/PLENTY OF WATER FOLLOWED
BY WASHING W/SOAP & WATER. INHAL:REMOVE TO FRESH AIR. APPLY ARTF
RESP & OTHER SUPPORTIVE MEASURES AS REQ. OTHER:IF ANY OF FOLLOWING
OCCUR DURING/FOLLOWING USE OF PROD, CALL POIS CTL CTR, EMERG ROOM
OR MD IMMED:HAVE MSDS INFO AVAIL. INGEST, EXCESS EXPOS TO
CORROSIVE(ING 7)
===================== Fire Fighting Measures =====================
Flash Point Method:PMCC
Extinguishing Media:NFPA CLASS B EXTING (CO*2/DRY CHEM/UNIVERSAL AQ
FILM FORMING FOAM) DESIGNED TO EXTING NFPA CLASS IIIB COMBUST LIQ
FIRES
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. WATER SPRAY MAY BE INEFTIVE BUT MAY BE USED TO COOL CLSD CNTNRS
TO PVNT PRESS BUILDUP & POSS (SUPP DATA)
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE OR BURST
(DUE TO THE BUILD-UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME
HEAT.
Spill Release Procedures:PROVIDE MAXIMIM VENTILATION. ONLY PERS
EQUIPPED W/PROPER RESP & SKIN & EYE PROT SHOULD BE PERMITTED IN
AREA. REMOVE ALL SOURCES OF IGNITION. TAKE UP SPILLED MATL
W/SAWDUST, VERMICULITE, OR OTHER ABSOR B MATL & PLACE INTO
CONTAINERS FOR DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
====================== Handling and Storage ======================
Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LARGE
QTYS IN BUILDINGS DESIGNED & PROTECTED FOR STORAGE OF NFPA CLASS
IIIB COMBUSTIBLE LIQUIDS. PROTECT FROM FREEZING.
Other Precautions:IF MATERIAL IS PART OF MULTIPLE COMPONENT COATING
SYSTEM, READ MSDS FOR OTHER COMPONENT OR COMPONENTS BEFORE BLENDING
AS THE RESULTING MIXTURE MAY HAVE THE HAZARDS OF ALL ITS PARTS.
Respiratory Protection:WHERE VENTILATION IS INADEQUATE, USE A
NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:PROVIDE GEN DILUTION OR LOC EXHST VENT IN VOLUME & PATTERN
TO KEEP CONC OF INGREDS BELOW LOWEST SUGGESTED EXPOS (ING 8)
Protective Gloves:NITRILE, NEOPRENE OR LATEX GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:IMPERMEABLE APRON.
Work Hygienic Practices:CLEAN OR DISCARD CONTAMINATED CLOTHING & SHOES.
Supplemental Safety and Health
FIRE FIGHT PROC:AUTOIGNIT OR EXPLO WHEN EXPOSED TO EXTREME HEAT. IF
WATER IS USED, FOG NOZZ ARE PREF. EFTS OF OVEREXP:PRLNGD EXPOS TO
INGREDS MAY CAUSE KIDNEY &/OR LIVER DMG. REDNESS, ITCHING, BURNING
SENSATION & VISUAL DISTURBANCES MAY INDICATE EXCESS EYE CONT.
DRYNESS, ITCHING, CRACKING, BURNING, REDNESS, & (ING 6)
HCC:N1
Boiling Pt:B.P. Text:>212F,100C
Vapor Pres:14.9
Vapor Density:HVR/AIR
Spec Gravity:1.78
Evaporation Rate & Reference:22 (BUTYL ACETATE=100)
Solubility in Water:35.9%
Appearance and Odor:VISCOUS LIQUID WITH ODOR CHARACTERISTIC OF THE
CHEMICAL FAMILY & SOLVENTS LISTE
Percent Volatiles by Volume:57.50
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRODUCE HAZ DECOMP PRODS WHEN
HEATED. WELDING, BRAZING OR FLAME-CUTTING ON SURFS COATED W/PROD
MAY PRODUCE CO FUMES.
Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL, AND LOCAL ENVIRONMENTAL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WASTE MANA GEMENT FACILITY.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.