===================== Product Identification =====================
MSDS NAME:INCONEL WELDING ELECTRODES 182T
NIIN:01-080-6481
MSDS Number: BQFDK
=== Responsible Party ===
Company:INCO ALLOYS INTERNATIONAL INC,WELDING PRODUCTS CO
Address:1401 BURRIS RD
City:NEWTON
State:NC
ZIP:28658-1754
Country:US
Info Phone Num:800-624-3411, 704-465-0352
Emergency Phone Num:304-526-5780
CAGE:9Z762
=== Contractor Identification ===
Company:INCO ALLOYS INTERNATIONAL INC
Address:1401 BURRIS RD
Box:City:NEWTON
State:NC
ZIP:28658-1754
Country:US
Phone:800-624-3411
CAGE:9Z762
============= Composition/Information on Ingredients =============
Name:CALCIUM CARBONATE (MARBLE) (LIMESTONE)
CAS:1317-65-3
RTECS #:EV9580000
Fraction by Wt: 5-10%
Other REC Limits:NONE SPECIFIED
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST; 9192
Name:CHROMIUM (SARA III)
CAS:7440-47-3
RTECS #:GB4200000
Fraction by Wt: 10-30%
Other REC Limits:NONE SPECIFIED
OSHA PEL:1 MG/M3
ACGIH TLV:0.5 MG/M3; 9192
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB
Name:IRON
CAS:7439-89-6
RTECS #:NO4565500
Fraction by Wt: 5-10%
Other REC Limits:NONE SPECIFIED
OSHA PEL:10 MG/M3 FUME
ACGIH TLV:5 MG/M3 FUME
Name:MANGANESE (SARA III)
CAS:7439-96-5
RTECS #:OO9275000
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
OSHA PEL:(C) 5 MG/M3 DUST
ACGIH TLV:5 MG/M3 DUST 9293
Name:MANGANESE OXIDE
CAS:1317-35-7
RTECS #:OP0895000
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
OSHA PEL:(C),5 MG/M3(MN)
ACGIH TLV:5 MG MN/M3; 9293
Name:MOLYBDENUM
CAS:7439-98-7
RTECS #:QA4680000
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3; 9293
Name:CRYOLITE, SODIUM ALUMINUM FLUORIDE, SODIUM FLUOALUMINATE
CAS:15096-52-3
RTECS #:WA9625000
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
Name:SILICATE BINDERS (SODIUM SILICATE)
CAS:1344-09-8
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
Name:NICKEL (SARA III)
CAS:7440-02-0
RTECS #:QR5950000
Fraction by Wt: 40-70%
Other REC Limits:1 MG/M3
OSHA PEL:1 MG/M3
ACGIH TLV:1 MG/M3; 9192
Name:COLUMBIUM, NIOBIUM
CAS:7440-03-1
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
Name:TITANIUM (DRY POWDER) (TI)
CAS:7440-32-6
RTECS #:XR1700000
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
Name:TITANIUM DIOXIDE
CAS:13463-67-7
RTECS #:XR2275000
Fraction by Wt: 1-5%
Other REC Limits:NONE SPECIFIED
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST; 9293
Name:SILICA, CRYSTALLINE - FUSED
CAS:60676-86-0
RTECS #:VV7328000
Fraction by Wt: 0.1-1.0%
Other REC Limits:NONE SPECIFIED
OSHA PEL:SEE TABLE Z3
ACGIH TLV:0.1 MG/M3 RDUST;9293
===================== Hazards Identification =====================
LD50 LC50 Mixture:ORAL (RAT) LD50: >9,000 MG/M3 (NICKEL)
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:EYES: WELDING FUMES AND DUST MAY CAUSE
IRRITATION, CONJUNCTIVITIS. SKIN: FUMES AND DUST MAY CAUSE
IRRITATION, DERMATITIS. INHALATION: FUMES AND DUST MAY, DEPENDING
ON THE SPECIFIC FEATURES OF THE PROC ESS USED, POSE A LONG TERM
HEALTH HAZARD. INGESTION: HEALTH HAZARDS, IF ANY,DEPENDS ON THE
SPECIFIC WELDING INGREDIENTS.
Effects of Overexposure:EYES: IRRITATION, CONJUNCTIVITIS. SKIN:
IRRITATION, DERMATITIS. INHALATION: ALLERGIC REACTIONS, RESPIRATORY
TRACT IRRITATION, AND HEALTH HAZARDS DEPENDING ON THE SPECIFIC
FEATURES OF THE PROCESS USED. INGESTION: DIGESTIVE TRACT
DISTURBANCES. HEALTH HAZARDS, IF ANY, DEPENDS ON THE SPECIFIC
WELDING INGREDIENTS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
======================= First Aid Measures =======================
Eyes: FLUSH WITH LARGE AMOUNTS OF WATER. IF IRRITATION
PERSISTS GET MEDICAL ATTENTION. SKIN: WASH AREA WITH SOAP AND
WATER. IF RASH DEVELOPS GET MEDICAL ATTENTION. INHALATION: MOVE TO
FRESH AIR. IF SE VERE RESPIRATORY IRRITATION PERSISTS GET MEDICAL
ATTENTION. INGESTION: GET MEDICAL ATTENTION.
===================== Fire Fighting Measures =====================
Flash Point:NONFLAMMABLE
Extinguishing Media:MEDIA SUITABLE FOR SURROUNDING FIRE.
Fire Fighting Procedures:NONE SPECIFIED BY MANUFACTURER.
Unusual Fire/Explosion Hazard:SPARKS FROM WELDING IN USER OPERATIONS
COULD IGNITE FLAMMABLE OR COMBUSTIBLE LIQUIDS, VAPORS, AND SOLIDS.
================== Accidental Release Measures ==================
Spill Release Procedures:VACUUM OR SHOVEL ANY SPILLED MATERIAL INTO A
SUITABLE CONTAINER. ALLOY WASTE ARE NORMALLY COLLECTED TO RECOVER
MATAL VALUES.
Neutralizing Agent:NONE
====================== Handling and Storage ======================
Handling and Storage Precautions:NONE SPECIFIED BY MANUFACTURER.
Other Precautions:USE INDUSTRIAL HYGIENE AIR MONITORING TO INSURE USE
OF THIS MATERIAL DOES NOT CREATE EXPOSURES EXCEEDING RECOMMENDED
EXPOSURE LIMITS.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:USE AIR-SUPPLIED RESPIRATOR IN CONFINED SPACES.
RESPIRATORY PROTECTION IS NECESSARY WHEN EXPOSURE LIMITS FOR
AIRGORNE CONTAMINANTS ARE EXCEEDED DURING WELDING WITH THESE
ELECTRODES. USE ONLY NIOSH APP ROVED IN ACCORDANCE W/29 CFR
1910.134.
Ventilation:USE LOCAL EXHAUST WHEN WELDING. PROVIDE ADEQUATE
VENTILATION TO MAINTAIN EXPOSURES BELOW ACCEPTABLE EXPOSURE LIMITS.
Protective Gloves:WEAR PROTECTIVE WELDER GLOVES.
Eye Protection:WEAR WELDER'S FACE AND EYE SHIELD.
Other Protective Equipment:FACE PROTECTION, FLAME RETARDANT CLOTHING,
AND RECOMMENDED LENS SHADE.
Work Hygienic Practices:WASH AFTER HANDLING AND BEFORE EATING,
DRINKING, OR SMOKING. LAUNDER CONTAMINATED CLOTHING BEFORE REUSE.
Supplemental Safety and Health
INGREDIENTS OF FUMES AND GASES GENERATED IN WELDING DEPENDS ON
ELECTRODE TYPE AND ITS FLUX, BASE METAL AND SPECIFIC PROCESS BEING
USED. INGREDIENTS MAY INCLUDE METALS, METAL OXIDES, CHROMATES,
FLUORID ES, CARBON MONOXIDE, OZONE, AND OXIDES OF NITROGEN.
PHOSGENE CAN BE PRODUCED IF CHLORINATED SOLVENT VAPORS ARE PRESENT.
================== Physical/Chemical Properties ==================
HCC:N1
Melt/Freeze Pt:M.P/F.P Text:>1832F,>100
Spec Gravity:4-6 GM/CC
Appearance and Odor:METALLIC SILVER COLORED SOLID WIRE WITH A FLUXX
COATING OR FLUX CORE, ODORLESS.
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:THIS PRODUCT IS NON-REACTIVE (STABLE) AS
SHIPPED.
Hazardous Decomposition Products:INGREDIENTS MAY INCLUDE METALS, METAL
OWXIDES, CHROMATES, FLU0RIDES, CARBON MONOXIDE, OZONE, AND OXIDES
OF NITROGEN.
Conditions to Avoid Polymerization:WILL NOT OCCUR.
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSE OF WASTE IN ACCORDANCE WITH LOCAL, STATE
AND FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|
|