MSDS NAME:POLY(VINYL CHLORIDE), MEDIUM MOLECULAR WEIGHT,34677-2
NIIN:00N050014
MSDS Number: BVJGP
=== Responsible Party ===
Company:ALDRICH CHEMICAL CO INC
Box:355
City:MILWAUKEE
State:WI
ZIP:53201
Country:US
Info Phone Num:414-273-3850
Emergency Phone Num:414-273-3850
CAGE:60928
=== Contractor Identification ===
Company:ALDRICH CHEMICAL CO INC
Address:1001 WEST ST PAUL AVE
Box:355
City:MILWAUKEE
State:WI
ZIP:53233
Country:US
Phone:414-273-3850
CAGE:60928
============= Composition/Information on Ingredients =============
Name:ETHYLENE, CHLORO-, POLYMER; (POLYVINYL CHLORIDE RESIN).
(MAY CONTAIN TRACE AMOUNTS OF ING 2)
CAS:9002-86-2
RTECS #:KV0350000
OSHA PEL:N/K
ACGIH TLV:N/K
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: MAY BE HARMFUL BY INHALATION,
INGESTION, OR SKIN ABSORPTION. CAUSES EYE AND SKIN IRRITATION.
MATERIAL IS IRRITATING TO MUCOUS MEMBRANES AND UPPER RESPIRATORY
TRACT. TO THE BEST OF MFR KNOWLEDGE , THE CHEMICAL, PHYSICAL, AND
TOXICOLOGICAL PROPERTIES HAVE NOT BEEN THORO INVESTIGATED.
Explanation of Carcinogenicity:CONTAINS A TRACE AMOUNT OF VINYL
CHLORIDE, A KNOWN HUMAN CARCINOGEN.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
======================= First Aid Measures =======================
Eyes: IMMED FLUSH WITH COPIOUS AMOUNTS OF WATER FOR AT LEAST
15 MINUTES. SKIN: IMMED FLUSH WITH COPIOUS AMOUNTS OF WATER FOR AT
LEAST 15 MINUTES WHILE REMOVING CONTAMD CLTHG & SHOES. INHAL:
REMOVE TO FRESH AIR. IF NOT BRTHG GIVE ARTF RESP.IF BRTHG IS
DFCLT, GIVE OXYGEN. INGEST: WASH OUT MOUTH W/WATER PROVIDED PERSON
IS CONSCIOUS. CALL A PHYS.
===================== Fire Fighting Measures =====================
Extinguishing Media:WATER SPRAY. CARBON DIXOIDE, DRY CHEMICAL POWDER OR
APPROPRIATE FOAM.
Fire Fighting Procedures:NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP. DO
NOT DIRECT A SOLID STREAM OF WATER/FOAM INTO BURNING MOLTEN
MATERIAL; THIS MAY CAUSE SPATTERING & (SUPDAT)
Unusual Fire/Explosion Hazard:EMITS TOXIC FUMES UNDER FIRE CONDITIONS.
Spill Release Procedures:WEAR NIOSH/MSHA APPRVD SCBA, RUBBER BOOTS &
HEAVY RUBER GLOVES. SWEEP UP, PLACE IN A BAG AND HOLD FOR WASTE
DISPOSAL. AVOID RAISING DUST. VENT AREA AND WASH SPILL SITE AFTER
MATL PICKUP IS COMPLETE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
====================== Handling and Storage ======================
Handling and Storage Precautions:DO NOT BREATHE DUST. AVOID CONT
W/EYES, SKIN & CLTHG. AVOID PRLNGD/RPTD EXPOS. IRRITANT. STORE IN A
COOL DRY PLACE.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.
Respiratory Protection:WEAR APPROPRIATE NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:MECHANICAL EXHAUST REQUIRED.
Protective Gloves:CHEMICAL-RESISTANT GLOVES.
Eye Protection:SAFETY GOGGLES.
Other Protective Equipment:OTHER PROTECTIVE CLOTHING.
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING.
Supplemental Safety and Health
FIRE FIGHT PROC: SPREAD FIRE.
Waste Disposal Methods:DISSOLVE/MIX MATERIAL WITH A COMBUSTIBLE SOLVENT
& BURN IN A CHEMICAL INCINERATOR EQUIPPED W/AN AFTERBURNER &
SCRUBBER.OBSERVE ALL FEDERAL, STATE AND LOCAL ENVIRONMENTAL REGS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.