strong base anion exchange polymer chloride ion form;(quat water supp data: for information on the design, installation, use ing 3: normal operating conditions.
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYE: MAY CAUSE IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
======================= First Aid Measures =======================
First Aid:EYE: FLUSH W/LGE AMT OF WATER FOR AT LEAST 15 MINS. CONSULT
MD IF IRRITATION PERSISTS. SKIN: FLUSH W/COPIOUS AMOUNTS OF WATER.
SEE MD. INHAL: REMOVE TO FRESH AIR. SUPPORT BREATHING(GIVE O*2/ARTF
RESP). INGEST: CALL MD IMMEDIATELY.
===================== Fire Fighting Measures =====================
Extinguishing Media:USE FOLLOWING EXTING MEDIA WHEN FIGHTING FIRES
INVOLVING THIS MATL: CARBON DIOXIDE, DRY CHEMICAL, WATER SPRAY.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT.
Unusual Fire/Explosion Hazard:COMBUSTION GENERATES TOXIC FUMES OF
NITROGEN OXIDES, HYDROGEN CHLORIDE.
Spill Release Procedures:WEAR GLOVES MADE OF COTTON/CANVAS. ADDTNL PERS
PROT EQUIP SHOULD INCL SAFETY GLASSES(ANSI Z87.1/APPRVD
EQUIVALENT). FLOOR MAY BE SLIPPERY; USE CARE TO AVOID FALLING.
TRANSFER SPILLED MATL TO SUITABLE CNTNRS FOR RECOVERY OR DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
====================== Handling and Storage ======================
Handling and Storage Precautions:MIN RECOM STOR TEMP FOR MATL IS
OC/32F. MAX RECOM STOR TEMP FOR MATL IS 60C/140F. KEEP FROM
FREEZING; MATL STABILITY MAY BE AFFECTED.
Other Precautions:MAX RECOM OP TEMP FOR MATL IS 77C/170F. PROPERLY
DESIGNED EQUIP IS VITAL IF THESE ION EXCHANGE RESINS ARE TO BE USED
IN CONJUNCTION W/STRONG OXIDIZING AGENTS SUCH AS NITRIC ACID TO
PVNT RAPID BUILD-UP OF PRESS & POSS EXPLOS. CONSULT(SUPDAT)
Respiratory Protection:RESP PROT PROGRAM MEETING OSHA 1910.134 & ANSI
Z88.2 REQS MUST BE FOLLOWED WHENEVER WORKPLACE CNDTNS WARRANT
RESPIRATORS USE. NONE REQUIRED UNDER NORMAL OPERATING CONDITIONS.
USE NIOSH/MSHA APPRVD RES P APPROP FOR EXPOS OF CONCERN.
Ventilation:VENT SYS EMPLOYED IS DEPENDENT ON USER'S SPEC APPLIC OF
MATL. REFER TO CURRENT EDITION OF INDUSTRIAL VENT: A (SUPDAT)
Protective Gloves:IMPERVIOUS GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGS.
Other Protective Equipment:EMERG EYE WASH AND DELUGE SHOWER WHICH MEET
ANSI DESIGN CRITERIA .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
PH: 7-9 AQUEOUS SLURRY. OTHER PREC: A SOURCE KNOWLEDGEABLE IN HNDLG OF
MATLS BEFORE PRECEDING. DO NOT PACK COLUMN W/DRY ION EXCHANGE
RESINS. DRY BEADS EXPAND WHEN WETTED; THIS EXPANSION CAN CAUSE GLAS
S COLUMNS TO SHATTER. VENT: MANUAL OF RECOM PRAC PUBLISHED BY
AMERICAN CONFERENCE OF GOVT INDUSTRIAL HYGIENISTS(ING 3)
Waste Disposal Methods:UNUSED RESIN MAY BE INCINERATED/LANDFILLED IN
FACILITIES MEETING LOCAL, STATE & FEDERAL REGULATIONS. FOR CONTAMD
RESIN, THE USER MUST DETERMINE THE HAZARD AND USE AN APPROPRIATE
DISPOSAL METHOD.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.