===================== Product Identification =====================
MSDS NAME:03-BL-51 BASE,BLUE 35450,POLYURETHANE
NIIN:01-015-7339
Kit Part:Y
MSDS Number: BGDNR
=== Responsible Party ===
Company:DEFT CHEMICAL COATINGS
Address:17451 VON KARMAN AVE
City:IRVINE
State:CA
ZIP:92714-6205
Country:US
Emergency Phone Num:NONE
CAGE:EO418
=== Contractor Identification ===
Company:AMERICAN STANDARDS INC
Address:11187 SUN CENTER DR
Box:City:RANCHO CORDOVA
State:CA
ZIP:95670-6120
Country:US
Phone:916-635-5800
CAGE:44361
Company:DEFT CHEMICAL COATINGS
CAGE:EO418
Company:DEFT, INC.
Address:17451 VON KARMAN AVE
City:IRVINE
State:CA
ZIP:92614
Country:US
Phone:949-474-0400
CAGE:33461
============= Composition/Information on Ingredients =============
Name:METHYL ETHYL KETONE (2-BUTANONE) (MEK) (SARA III)
CAS:78-93-3
RTECS #:EL6475000
Fraction by Wt: 11.0%
OSHA PEL:200 PPM/300 STEL
ACGIH TLV:200 PPM/300STEL 9192
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS
Name:2-ETHOXYETHYL ACETATE (CELLOSOLVE ACETATE) (EGEEA)
CAS:111-15-9
RTECS #:KK8225000
Fraction by Wt: 21.0%
OSHA PEL:S,100 PPM
ACGIH TLV:S, 5 PPM; 9192
Name:ETHYL ACETATE (CAS #141-78-6) (%WT 11 PLUS/MINUS 2)
RTECS #:AH4250000
Fraction by Wt: 13.0%
ACGIH TLV:400 PPM
Name:DIBUTYL TIN DILAURATE (AS TIN)
CAS:77-58-7
RTECS #:WH7000000
Fraction by Wt: 0.05%
OSHA PEL:S, 0.1 MG/M3
ACGIH TLV:S, 0.1 MG/M3; 8990
Name:NON-AQUEOUS SOLUTION,HAZARD UNKNOWN,UNIDENTIFIED(% WT TAKEN
BY DIFFERENCE 54.95)
Fraction by Wt: 55.0%
===================== Hazards Identification =====================
Effects of Overexposure:SKIN/EYE:IRRTIATION;INH:IRRIT OF RISP
TRACT.ACUTE NERVOUS STSTM DEPRESSION FOLLOWD BY HEAD/DIZZ.
======================= First Aid Measures =======================
First Aid:EYES/SKIN:FLUSH IMMEDIATELY WITH WATER FOR 15 MIN. REMOVE
CONTAMINATED CLOTHING. INHALES: REMOVE TO FRESH AIR. GIVE CPR OR
OXYGEN IF NEEDED. KEEP WARM/QUIET.GET MEDICAL ATTENTION. EFFECTS
SHOULD DISAP PEAR AFTER 10 MIN.
===================== Fire Fighting Measures =====================
Flash Point:20F(-6.6C)-TCC
Extinguishing Media:CO*2, FOAM, DRY CHEM & H*2O FOG.
Fire Fighting Procedures:WEAR SCBA. COOL EXPD. CONTRS W/H*2O. H*2O
INEFF. ON FIRE.
Unusual Fire/Explosion Hazard:CONTRS MAY EXPLD IN HT OF FIRE. RUNOFF TO
DRS MAY CRTE FIRE OR EXPLOS. HAZ FLAMM VAP MAY SPRD FR SPL
================== Accidental Release Measures ==================
Spill Release Procedures:EVACUATE UNPROTECTED PERSONS. ELIM IGNITION
SOURCES. STOP LEAK. H*2O SPRAY COOL CONT/DIVERT SPILL FROM
FIRE/HEAT. PROVIDE VENTILATION. ABSORB W/COMMERCIAL
ABSORBENT,SHOVEL INTO METAL DRUMS:LG SPILL:DI KE W COMMERCIAL
ABSORBENT,PUMP INTO COVERED DRUMS.
====================== Handling and Storage ======================
Handling and Storage Precautions:STORE IN COOL,DRY,WELL VENT,LOW FIRE
RISK AREA. PROTECT FROM PHYSICAL DAMAGE.AVOID ANY PHYSICAL CONTACT.
KEEP CONTAINERS TIGHTLY CLOSED.
Other Precautions:PREVENT PROLONGD/REPEATD BREATHING OF VAP OR SPRAY
MIST.CAN CAUSE ALLERGIC REACTION.FOLLOW SPECIAL PRECAUTIONS TO
APPLY ON HOT SURFACES.IF WATER IS USED FOR FIRE,FOG NOZZLES ARE
PREFERABLE.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:SUPPLIED AIR RESPIR/SCBA; ESCAPE: GAS MASK
Ventilation:MECH(GEN)OR LOCAL EXHAUST THAT PROVIDES ADEQUATE
VENTILATION
Protective Gloves:RUBBER/NEOPRENE
Eye Protection:CHEM SPLASH GOGGLES
Other Protective Equipment:WEAR FULL PROTECTIVE CLOTHING.
Supplemental Safety and Health
MSDS FM MFR DATE:03/23/83; TWO PART RESIN MODIFIED POLYURETHANE
COATING; THIS DATA DESCRIBES BASE P/N INK "B" FOR CATALYST;
MIL-C-82286B.KEY1:F3.
================== Physical/Chemical Properties ==================
HCC:F2
Boiling Pt:B.P. Text:168-313F
Vapor Density:>1.0
Spec Gravity:1.2677
Evaporation Rate & Reference:<1(SLOWR THAN ETHR
Solubility in Water:NELIGIBLE
Appearance and Odor:BLUE PAINT
Percent Volatiles by Volume:56.9
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
OXIDIZERS, CORROSIVES, PEROXIDES
Stability Condition to Avoid:HIGH TEMPERATURES,IGNITION SOURCES
Hazardous Decomposition Products:CO*2, CO, TOXIC OXIDES.
Conditions to Avoid Polymerization:ELEVTD TEMPERATURE
==================== Disposal Considerations ====================
Waste Disposal Methods:ELIMINATE IGNITION SOURCES. DESTROY BY LIQUID
INCINERATION. INCINERATION WILL BE EASIER BY MIXING WITH A MORE
FLAMMABLE SOLVENT. HANDLE & DISPOSE IN FULL COMPLIANCE WITH ALL
APPLICABLE INTERNATIONAL,F ED,STATE & LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|