=====================  Product Identification  =====================

MSDS NAME:PARAFFIN WAX
NIIN:00-285-2045
MSDS Number: BHYCH
=== Responsible Party ===
Company:WALNUT HILL ENTERPRISES, INC.
Address:GREEN LANE & WILSON AVENUE
Box:599
City:BRISTOL
State:PA
ZIP:19007
Country:US
Info Phone Num:215-785-6511
Emergency Phone Num:215-785-6511
CAGE:0LM34
=== Contractor Identification ===
Company:WALNUT HILL ENTERPRISES INC
Address:GREEN LANE AND WILSON AVE
Box:599
City:BRISTOL
State:PA
ZIP:19007
Country:US
Phone:215-785-6511
CAGE:0LM34

=============  Composition/Information on Ingredients  =============

Name:PARAFFIN WAX; FULLY REFINED.
CAS:64742-43-4
Fraction by Wt: <100%
Other REC Limits:NONE SPECIFIED

Name:HYDROTREATED AND/OR CLAY-TREATED PARAFFIN WAX.
CAS:64742-51-4
Fraction by Wt: <100%
Other REC Limits:NONE SPECIFIED

=====================  Hazards Identification  =====================

Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:THIS WAX IS NON-TOXIC AND ITS MOST
    LIKELY HAZARD IS THERMAL BURNS OCCURRING WHEN MOLTEN WAX IS SPILLED
    ON THE SKIN, OR WHEN VAPORS OF OVERHEATED WAX ARE INHALED.
Explanation of Carcinogenicity:THIS PRODUCT IS NOT LISTED BY IARC, NTP
    OR OSHA AS A CARCINOGEN, MUTAGEN, TERATOGEN OR NEUROTOXIN.
Effects of Overexposure:THERMAL BURNS FROM CONTACT WITH MOLTEN WAX.
    RESPIRATORY IRRITATION, COUGHING FROM INHALING VAPOR FROM
    OVERHEATING.
Medical Cond Aggravated by Exposure:NONE REPORTED

=======================  First Aid Measures  =======================

First Aid:CONTACT WITH MOLTEN WAX:IMMEDIATELY COOL WITH WATER. REMOVE
    BY DISSOLVING WITH VEGETABLE OR MINERAL OIL. DO NOT PEEL OFF. SEE
    DOCTOR. INHALATION:REMOVE FROM EXPOSURE, AND TREAT SYMPTOMATICALLY.
    INGEST ION: CONSULT PHYSICIAN.

=====================  Fire Fighting Measures  =====================

Flash Point:>400F,>204C
Extinguishing Media:USE CARBON DIOXIDE, FOAM, OR DRY CHEMICAL. DO NOT
    USE WATER.
Fire Fighting Procedures:FIRE FIGHTERS SHOULD USE NIOSH APPROVED SCBA &
    FULL PROTECTIVE EQUIPMENT WHEN FIGHTING CHEMICAL FIRE. USE WATER
    SPRAY TO COOL NEARBY CONTAINERS EXPOSED TO FIRE.
Unusual Fire/Explosion Hazard:FIRE OR EXCESSIVE HEAT MAY CAUSE
    PRODUCTION OF HAZARDOUS DECOMPOSITION PRODUCTS.

==================  Accidental Release Measures  ==================

Spill Release Procedures:SPILLED LIQUID:KEEP OUT OF DRAINS, SEWERS, AND
    WATERWAYS. COOL TO SOLIDIFY AND SCRAPE OR SCOOP INTO CONTAINERS FOR
    RECYCLE OR DISPOSAL. SOLID:SWEEP OR PICK UP.
Neutralizing Agent:NONE

======================	Handling and Storage  ======================

Handling and Storage Precautions:DO NOT HEAT ABOVE FLASHPOINT. DO NOT
    HEAT WITH OPEN FLAME OR OPEN ELECTRICAL COIL.
Other Precautions:AVOID CONTAMINATION BY USING CLOSED CONTAINERS. FIRE
    EXTINGUISHERS SHOULD BE READILY AVAILABLE.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:RESPIRATOR WILL NOT NORMALLY BE NECESSARY. USE
    NIOSH/MSHA APPROVED AIR SUPPLIED RESPIRATOR OR RESPIRATOR FOR OIL
    MIST IF EXPOSURE IS ABOVE THE TLV/PEL. SEE 29 CFR 1910.134 FOR
    REGULATIONS PERTAINING T O RESPIRATOR USE.
Ventilation:NORMAL ROOM VENTILATION SHOULD BE SUFFICIENT. SUPPLEMENT
    WITH LOCAL EXHAUST IF NEEDED (VAPORS FROM HEATING).
Protective Gloves:HEAT RESISTANT
Eye Protection:SAFETY GLASSES
Other Protective Equipment:WEAR CLOTHING AND EQUIPMENT NECESSARY TO
    PROTECT FROM SPLASHES WHEN HANDLING MOLTEN WAX.
Work Hygienic Practices:USE GOOD INDUSTRIAL HYGIENE PRACTICE. MINIMIZE
    PERSONAL CONTACT.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

==================  Physical/Chemical Properties  ==================

HCC:N1
Boiling Pt:B.P. Text:SOLID
Melt/Freeze Pt:M.P/F.P Text:137F,58C
Spec Gravity:0.82
Solubility in Water:NEGLIGIBLE
Appearance and Odor:WHITE WAXY SOLID. NEARLY ODORLESS

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS
Stability Condition to Avoid:HIGH TEMPERATURES, OPEN FLAMES, OTHER
    IGNITION SOURCES.
Hazardous Decomposition Products:CARBON DIOXIDE,CARBON MONOXIDE

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISCARD ANY PRODUCT, RESIDUE, DISPOSAL CONTAINER
    OR LINER IN ACCORDANCE WITH ALL FEDERAL, STATE AND LOCAL
    REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***