LPS LABORATORIES
MSDS
MATERIAL SAFETY DATA SHEET
Section 1 - Product Identification and Use
Manufacturer's Name: Trade Name:
LPS Laboratories LPS Tapmatic AquaCut Cutting Fluid
Address (Number Street): Chemical Family:
4647 Hugh Howell Road Blended Compound
Address (City, State, Zip): Part Numbers:
Tucker, GA 30085-5052 01204, 01216, 01228, 01205
Telephone Number: 770-934-7800
Emergency Telephone Number: 1-800-424-9300 Chemtrec
Outside U.S.: (703) 527-3887
Hazardous Materials Description and proper shipping name (49 CFR 172.101):
Compound, Boiler, Preserving Liquid NMFC 50093 SUB 2 BRL/BXS CL55
TSCA Inventory: HMIS Labeling: Health: 1
All of the ingredients are listed on the TSCA inventory. Flammability: 0
Reactivity: 0
Section 2 - Hazardous Ingredients / Identity Information
ACGIH OTHER
Ingredients CAS Numbers %WW OSHA PEL TLV LIMITS
Amine Salt of Organic Phosphate Ester unknown 2-4 N.E. N.E. None
Section 3 - Physical / Chemical Characteristics
Boiling point (F潞): 212掳F Specific gravity (H20 = 1): 1.0
Vapor pressure ( mmHg) @100潞F: 18 Percent volatile by volume (%): 95
Vapor density (Air = 1): approx. 0.6 Evaporation rate (Water = 1): 1
Solubility in water: 100%
Appearance and odor: Clear, turquoise liquid with cinnamon odor.
Section 4 - Fire and Explosion Hazard
Flash point (method used): Nonflammable Flammable limits (of diluent ): LEL N.A. UEL N.A.
Extinguishing media: N.A.
Special fire fighting procedures: None
Unusual fire and explosive hazards: None
N.E. = Not established
N.A. = Not applicable
Section 5 - Health Hazard Data
Primary route(s) of entry: Inhalation, eyes
Health hazard/effects of over exposure:
Inhalation: Headache, dizziness, and nausea.
Eyes: Liquid will cause temporary irritation.
Skin: Repeated or prolonged contact may cause drying of skin.
Ingestion: Not a likely route of exposure. Ingestion may result in nausea, abdominal discomfort, or diarrhea.
Medical conditions aggravated by exposure: None known.
Chemicals listed as potential carcinogen: NTP: No IARC: No OSHA: No
Emergency and first aid procedures:
Inhalation: Move to fresh air and provide oxygen if breathing is difficult.
Eyes: Flush eyes with plenty of water. If irritation persists, contact physician.
Skin: Wash with soap and water; apply medicated skin cream.
Ingestion: Give two glasses of water and induce vomiting immediately by touching finger to back of victim's
throat. Never give anything by mouth to an unconscious person.
Section 6 - Reactivity Data
Stability: Stable Conditions to avoid: None
Incompatibility (Materials to avoid): Magnesium and strong oxidizing agents.
Hazardous decomposition products: Carbon monoxide upon thermal decomposition.
Hazardous polymerization: Will not occur.
Section 7 - Precautions for Safe Handling and Use
Steps to be taken in case material is released or spilled: Remove leaking container and contain spill. Soak or mop up
with absorbent material and discard.
Waste disposal methods: Dispose of in accordance with local, state and federal regulations
RCRA Hazardous Waste No.: N.A.
CERCLA Reportable Quantity: None
SARA TITLE III Chemicals: None
Precautions to be taken in handling and storage: Product should be stored above 20掳F and below 120掳F. Keep
containers closed when not in use.
Section 8 - Control Measures
Respiratory Protection: None required if good ventilation is maintained.
Ventilation: Local exhaust is usually adequate.
Protective gloves: N.A.
Eye protection: Safety glasses.
Other protective equipment: N.A.
Work/hygienic practices: Wash hands with soap and water after use and/or before breaks, lunch and at the end of work
periods. Remove contaminated clothing and launder before reuse.
Section 9 - Preparation Date of MSDS
The foregoing technical information and recommendations are compiled from sources that are believed to be accurate and reliable.
However, they are supplied without warranty or guarantee of any kind either expressed or implied. The purchaser is responsible for
selecting and determining the suitability of products for purchaser鈥檚 particular needs and we disclaim any responsibility for improper
applications or misuse of our products in any manner whatsoever.
January 31, 2000
Fred Fugitt, Technical Services Chemist
Ed Williams, Manager of Research and Development Form # 2576
LPS Laboratories LPS Tapmatic AquaCut Cutting Fluid
|