TECHNICAL DATA
Supatuff Anti-Slip Coating
Supatuff AS-550
Description
Supatuff Anti-Slip Coating is a high solids, heavy duty, non-slip coating for application in slippery areas to make
them safer for both pedestrian and rolling equipment traffic.
Supatuff Anti-Slip Coating was developed for use in marine and industrial environments to provide a durable
surface with the highest possible non-slip profile. The coating was engineered to with stand heavy traffic from forklifts,
steel-wheeled vehicles and pedestrians.
Formulated with epoxy resins to provide optimum toughness and corrosion resistance, Supatuff Anti-Slip Coating is
resistant to acids, alkalies, solvents, grease, oil, salt water, salt spray, detergents, alcohol, petrol, diesel, jet fuels, and
hydraulic fluids. By virtue of its tenacious bond, rust will not creep under the coating if fractured.
Supatuff Anti-Slip Coating offers optimum adhesion to concrete and metal surfaces and the coatings sealed,
nonporous surface makes it easy to clean.
Areas of Application
鈥? 鈥?
Ramps for vehicular and pedestrian traffic Wet areas subject to vehicular and pedestrian traffic
鈥? 鈥?
Chemical plants Printing plants
鈥? 鈥?
Wharves and loading terminals Heavy manufacturing
鈥? 鈥?
Commercial fishing operations Oil refineries
鈥? 鈥?
Wet deck areas of cargo vessels Harsh marine environments
鈥? 鈥?
Fuel handling depots Stairways, catwalks and gangplanks
鈥? 鈥?
Oil platforms - any place that receives the Mining and Construction industries
harshest wear and tear
Features
鈥? 鈥?
Excellent non-slip properties Aggressive profile friction surface provides high traction
鈥? 鈥?
Highly chemical resistant Full range of colours available
鈥? 鈥?
Excellent wear resistance High build application
鈥? 鈥?
High impact resistance Easily applied
The information contained in this Technical Bulletin is as up to date and correct as possible as at the time of issue. The data
provided should be used as a guide only as the performance of the product will vary depending on differing operating conditions
and application methods.
The sale of any product described in this Technical Bulletin will be in accordance with ITW Polymers & Fluids Conditions Of Sale, a
copy of which is available on request. To the extent permitted by law, ITW Polymers & Fluids excludes all other warranties in
relation to this product.
Last Modified February 2004
Page 2 of 4
General Properties
Shelf life 2 years
:
Mixing Proportions by Volume 1 Hardener to 5 compound
:
Solids Content 93%
:
Density 1.92 kg/litre
:
Application Temperatures 10掳C 鈥? 40掳C
:
Work Time Per Pack 1 hour at 20掳C
:
Tack-free Time 8 hours at 20掳C
:
Cure Times
Light Traffic 24 hours at 20掳C
:
Heavy Traffic 72 hours at 20掳C
:
Full Chemical Resistance 7 days
:
Finish Semi gloss variegated profile
:
Colours Full range available
:
Abrasion Resistance Excellent
:
Coefficient of friction Dry 鈥? 0.88
:
Wet 鈥? 0.93
:
Water Resistance Excellent
:
Clean ability Very good
:
Up to 950C Dry Heat
Temperature Resistance :
Estimating Data
= 6.4 m2/ coat
Roller 8 litre Supatuff Anti-Slip Coating + 1 kg Colourpack
= 8.8 m2/ coat
Trowel 8 litre Supatuff Anti-Slip Coating + 1 kg Colourpack
Application Directions
Surface Preparation
Concrete
Remove any old paint and all loose material. New concrete must be at least 28 days old. Ensure surface is clean,
free of dust, laitence, oils, curing compounds or other contaminants. Remove any oil or grease contamination by
washing with a suitable degreaser. Hose off with high-pressure water and allow to dry. Acid etch using Epirez
Concrete Etch & Cleaner. Neutralise surface by washing with fresh water and allow to dry. Alternatively lightly
captive blast clean to expose firmly held aggregate to industrially accepted standards.
Steel
Ensure that the surface is free from oil and grease. Abrasive blast clean in accordance with AUSTRALIAN
STANDARD AS1627:9 - 2002 to a profile of 50 microns. Coating of the prepared steel should be completed within 4
hours.
Surface preparation guidelines cannot cover all site or field contingencies and it is always recommended that an on
the-spot adhesion test be performed as part of the Standard Quality Assurance audit for the project.
AUSTRALIA NEW ZEALAND
ITW Polymers & Fluids ITW Polymers & Fluids
100 Hassall Street 18-26 Amelia Earhart Avenue
Wetherill Park NSW 2164 Airport Oaks, Mangere, Auckland
Phone (02) 9757 8800 Fax (02) 9757 3855 Phone (09) 256 2122 Fax (09) 256 2124
Page 3 of 4
Priming
Supatuff Anti-Slip Coating may be directly applied to good quality dense prepared concrete. Porous, highly
absorbent concrete and steel should be primed with Epoxy Primer/ Sealer (123) prior to application to provide better
surface adhesion. Allow to dry for approximately 3 hours or until touch dry prior to the application of Supatuff Anti-
Slip Coating. Drying times will be lengthened by high humidity and low temperatures. Application of Supatuff Anti-
Slip Coating should take place within 24 hours after priming.
Application
Supatuff Anti-Slip Coating can be applied at surface temperatures between 10掳C and 40掳C. Application is not
recommended when surface temperatures are above 40掳C or below 10掳C. Curing times will increase substantially at
temperatures below 10掳C.
Add the complete contents of the selected colour pack to each 8 litre compound and mix thoroughly with a slow speed
(400 rpm) mechanical mixer. Make sure all settlement is lifted off the bottom of the container and is uniformly
dispersed in the material. Pour the entire contents of the hardener container into the compound and mix with the slow
speed mechanical mixer for approximately 3-5 minutes or until the mixed material assumes a uniform colour and
appearance. Scrape the bottom and sides during the mixing process to ensure all parts are mixed thoroughly.
Working pot life is approximately 1 hour at 20掳C. Supatuff Anti-Slip Coating can be applied by roller, trowel or spray
equipment if required.
Higher temperatures will shorten curing time and conversely, lower temperature will lengthen curing time. Exterior
applications must be protected from rain for at least 12 to 24 hours after application according to humidity. Protect
from heavy or extended exposure to water, oil and chemicals for 5 to 7 days during final cure.
ROLLER
Rolled applications provide the most aggressive non-slip characteristics with an irregular, ridged profile.
Use a hard faced roller. It is important that the rolled profile expose the maximum amount of non-slip aggregate. If
aggregate is not properly exposed, the coating may become slippery when wet. Pour a 鈥渞ibbon鈥? of Supatuff Anti-Slip
Coating on the surface approximately 600mm long and 150mm wide. Roll material in one direction only, in slow
straight strokes pulling material towards one with a moderate amount of pressure. Do not over-roll too many times or
press down too heavily. Be careful that material does not build up too quickly along welds (roll across, not along
them). Material applied too thickly may not cure properly.
TROWEL
Trowel applications provide excellent non-slip characteristics with a rough, textured surface.
Use a flexible bladed plasterer鈥檚 finishing trowel approximately 100mm by 300mm. Use smooth edges, not notched.
Pour a 鈥渞ibbon鈥? of Supatuff Anti-Slip Coating on the surface approximately 600mm long and 150mm wide. Hold
trowel at 45掳 angle to surface and spread with a sweeping motion. Reverse the angle of the trowel for the opposite
stroke. Pull material towards one. To cover corners, etc. pull using straight strokes using the material on the trowel.
Cleaning
Tools and equipment may be cleaned before hardening commences by washing with Epirez Clean Up Solvent. Do
not use for cleaning hands or mixing with product.
AUSTRALIA NEW ZEALAND
ITW Polymers & Fluids ITW Polymers & Fluids
100 Hassall Street 18-26 Amelia Earhart Avenue
Wetherill Park NSW 2164 Airport Oaks, Mangere, Auckland
Phone (02) 9757 8800 Fax (02) 9757 3855 Phone (09) 256 2122 Fax (09) 256 2124
Page 4 of 4
Limitations
Supatuff Anti-Slip Coating Should not be applied at temperatures below 100C or temperatures above 400C.Curing
times will increase substantially at temperatures below 100C.
Supatuff Anti-Slip Coating should not be applied to surfaces known to suffer from rising damp.
Supatuff Anti-Slip Coating is not recommended for application over tiles.
For more information contact the technical department.
Maintenance
Maintain a clean surface to ensure that the non-slip safety performance of Supatuff Anti-Slip Coating be maximised.
The following cleaning procedure is recommended.
Clean with a neutral detergent cleaner mixed as directed with water. For stubborn oil and grease use a suitable
surface degreaser prior to cleaning with a neutral detergent. Scrub surface with a long handled, fibre-bristle brush or
floor machine. Rinse with clean water and dry.
Note: It is important that manufacturer鈥檚 instructions on dilutions of cleaning solutions are followed.
Packaging
Supatuff Anti-Slip Coating is available in 8 litre packs. Each pack contains Hardener and Compound in correct
proportions for use. Selected Colourpack must be added.
Ordering Information:
Supatuff Anti-Slip Coating Neutral 8 litre #992908
Colourpack 1 kg #Various
Safety Precautions
Follow normal coating procedures. Keep away from fire or naked flame. Keep contents away from children. If
swallowed call a Doctor or Poisons Information Centre. If swallowed DO NOT induce vomiting. When mixing or using,
avoid skin contact or breathing of vapours. If splashed on skin, wash with warm soapy water. During application,
wear protective clothing and where necessary, goggles and mask or respirator. Provide adequate fresh air
ventilation.
TDG Code: Hardener - UN 1760 Compound / Colour Pack (Various) - Not Classified
Note
The figures quoted for work time, setting time and strengths are not definitive. They are dependent on job site
conditions and will vary accordingly. In all cases we endeavour to provide typical figures for use as a guide.
Health & Safety Information
The product is hazardous. A Material Safety Data Sheet is available from the ITW Polymers & Fluids Technical
Department upon request or available on our website www.epirez.com.au .
AUSTRALIA NEW ZEALAND
ITW Polymers & Fluids ITW Polymers & Fluids
100 Hassall Street 18-26 Amelia Earhart Avenue
Wetherill Park NSW 2164 Airport Oaks, Mangere, Auckland
Phone (02) 9757 8800 Fax (02) 9757 3855 Phone (09) 256 2122 Fax (09) 256 2124
|