May 2008 Page 1 of 3
MATERIAL SAFETY DATA SHEET
MAY BE USED TO COMPLY WITH OSHA'S HAZARD COMMUNICATION STANDARD, 29 CFR 1910.1200 AND SUPERFUND
AMENDMENTS AND REAUTHORIZATION ACT (SARA) OF 1986 PUBLIC LAW 99-499. STANDARD
SHOULD BE CONSULTED FOR SPECIFIC REQUIREMENTS.
SECTION I (IDENTIFICATION)
MANUFACTURER/ EUTECTIC CORPORATION TELEPHONE NUMBER:
SUPPLIERS NAME: 94 W14355 Garwin Mace Drive 1-800-558-8524
Menomonee Falls, WI 53051 USA
PRODUCT NAME: StainTin 157 Pa Syringe
PRODUCT CLASSIFICATION: Solder Paste (Lead < 0.1 %)
SECTION II (HAZARDOUS INGREDIENTS/IDENTITY INFORMATION)
IMPORTANT: This section covers the materials from which these products are manufactured. The fumes and gases produced during normal use of these
products are covered in Section V. The term "Hazardous" in "Hazardous Ingredients" should not only be interpreted as a term required and defined in OSHA
Hazard Communication Standard (29 CFR Part 1910.1200), but also as defined by other regulatory agencies. The chemicals or compounds subject to
reporting under Title III, in Section 313, of the Superfund Amendments and Reauthorization Act (SARA) are marked by the symbol #.
WARNING: This product contains or produces a chemical known to the State of California to cause birth defects (or other reproductive harm) and cancer.
(California Health & Safety Code 25249.5 et seq.)
EXPOSURE LIMIT (mg/m鲁) WEIGHT
INGREDIENTS CAS No. OSHA PEL ACGIH TLV PERCENT INGREDIENTS
Tin 7440-31-5 2 2 88 - 98
Silver # 7440-22-4 0.01 0.1 1-5
Sebacic Acid 111-20-6 n.a. n.a.
Diethylamine Hydrochloride 660-68-4 n.a. n.a.
Succinic Acid 110-15-6 n.a. n.a.
White Protopet IS 8009-03-8 n.a. n.a.
Percentages and formula are listed as proprietary.
SECTION III (POTENTIAL HEALTH EFFECTS AND HEALTH HAZARD DATA)
Target organ statement:
DANGER: Causes severe burns to eyes. May be an irritation to respiratory system and skin. Prolonged overexposure to silver can lead to
kidney damage.
SHORT TERM (ACUTE) OVEREXPOSURE TO PASTE:
Swallowing May cause burns of mouth and throat.
Inhalation Irritation to respiratory system. Coughing and sneezing, and may result in discomfort such as dizziness, nausea, or
dryness or irritation of nose, throat or eyes. Existing lung disorders will be aggravated.
Skin Contact Dermatitis. Existing disorders will be aggravated.
Eye Contact Irritation to the eyes, tearing, burn of the eye surfaces.
Brazing fumes cannot be classified simply. The composition and quantity of both are dependent upon the metal being brazed, the process,
procedure, and the filler material used. Other conditions which also influence the composition and quantity of the fumes and gases to which
workers may be exposed include: coatings on the metal being soldered (such as paint, plating, or galvanizing), the number of workers and the
volume of the work area, the quality and the amount of ventilation, position of the workers鈥? head with respect to the fume plume, as well as the
presence of contaminants in the atmosphere (such as chlorinated hydrocarbon vapors from cleaning and decreasing activities).
When the material is consumed, the fume and gas decomposition products generated are different in percent and form from the ingredients
listed in Section II. Fume and decomposition products, not the ingredients in the flux are important. Decomposition products include those
originating from the volatilization, reaction, or oxidation of materials in Section II, plus those from the base metal and coating, etc., as noted
above. These components are virtually always present as complex oxides and not as metals (Characterization of Arc Welding Fume: American
Welding Society).
MSDS: StainTin 157 Pa Syringe Page 2 of 3
SHORT TERM (ACUTE) AND CHRONIC OVEREXPOSURE:
WHITE PROTOPET IS: White protopet IS is a medical grade (USP) petrolatum and is nontoxic and fully complies with the Food and Drug
Administration鈥檚 requirement for petrolatum as per CFR 121.1166.
SEBACIC ACID: Acute exposure has low toxicity potential. However, long-term exposure has been found to produce irritation of the
respiratory tract and alteration of kidney and liver functions. Maximum recommended concentration of sebacic acid in working areas should
not exceed 4 mg/cu meter.
DIETHYLAMINE HYDROCHLORIDE: Material may be irritating to the eyes, skin and mucous membrane.
SUCCINIC ACID: Dust or mist, if inhaled, may irritate nose, throat, and lungs. Although small amounts may be used as a food additive,
large doses (10 grams), if ingested, produce a laxative reaction, possible vomiting, weakness and may irritate the gastrointestinal tract. Contact
with skin may cause slight skin irritation. Hot, concentrated solutions may cause burns. Severe eye irritant.
SILVER: Overexposure to silver dusts or fumes may cause a permanent grayish pigmentation of the skin and can cause irritation of the skin
and mucous membranes. Prolonged overexposure can lead to kidney damage.
TIN: Inhalation of tin oxide may lead to benign pneumoconiosis. Certain tin salts are mild irritants to the skin and mucous membranes.
CARCINOGENICITY
WELDING FUMES (not otherwise specified) are considered to be carcinogenic defined with no further categorization by NIOSH and IARC.
SECTION IV ( EMERGENCY AND FIRST AID PROCEDURES)
Swallowing: Call a physician at once or your poison control center. Advise of Section II immediately. Do not induce vomiting. If
conscious, give soluble calcium or magnesium in any form: milk, calcium gluconate or calcium lactate solutions, if available.
Do not give carbonates or bicarbonates.
Skin: Promptly flush with water for 15 minutes to remove all residue. If rash or burn develops, consult a physician. Remove
contaminated clothing and shoes. Wash contaminated clothing before reuse.
Inhalation: Remove to fresh air. If fumes are inhaled, call a physician.
Eyes: Flush with water for at least 15 minutes to remove all residue. Hold eyelids apart during irrigation. Get immediate medical
help!
SECTION V (FIRE AND EXPLOSION DATA)
Flashpoint: Will not burn.
Extinguishing media: Use CO2 or dry chemical extinguisher.
Special fire fighting procedures: Fire fighters should wear self-contained breathing apparatus and full protective clothing.
Unusual fire and explosion hazards: Dense smoke may be generated in a fire.
Rating under National Fire Protection 704: Health, 2; Flammability, 0; Reactivity, 1.
SECTION VI (REACTIVITY DATA)
Stability consideration: stable
Hazardous polymerization: will not occur
Conditions to avoid: Moisture, excessive heat during storage
Incompatibility: Materials to avoid: Oxidizing agents
Hazardous combustion or decompositions products: Carbon dioxide, carbon monoxide generated on heating.
SECTION VII ( SPILL AND LEAK RESPONSE)
Steps to be taken if material is released or spilled: Contain spill, absorb, sweep up and dispose. Flush area to chemical sewer.
Waste disposal method: Dispose of in accordance with all federal state, and local regulations.
MSDS: StainTin 157 Pa Syringe Page 3 of 3
SECTION VIII ( SPECIAL PROTECTION INFORMATION)
Respiratory protection: If the workstation is not properly ventilated to exhaust all fumes and vapors, use a NIOSH approved mask. Monitor
fume levels.
Ventilation: Adhere to environmental regulations for exhausts. Use enough ventilation, local exhaust at the arc, or both, to keep the fumes and
gases below the TLV鈥檚 in the workers breathing zone and the general area. Train the worker to keep his head out of the fumes. Maintain
airflow away from user to exhaust all dusts and fumes, so that the TLV is never exceeded.
Protective gloves: Rubber gloves.
Eye protection: Chemical safety goggles.
Other protective equipment: Full protective equipment normally used in soldering operation to prevent any contact. Review operations
to avoid contact with hazardous gas, liquid, or solid. See also:
29CFR 1910.132 - 29 CFR 1910.140 Personal Protective Equipment
29 CFR 1910.251 - 29 CFR 1910.257 Welding, Cutting and Brazing
SECTION IX (STORAGE, HANDLING AND SPECIAL PRECAUTIONS)
Precautions to be taken in handling and storage: Store 157Pa at ambient conditions. Store in plastic container or plastic lined or rubber
lined containers. Do not store in steel containers. Wash thoroughly after handling to remove all residue.
Other precautions: Do NOT breathe fumes. Professionally wash contaminated clothing before reuse. Existing lung disorders will have
increased toxic susceptibility.
SECTION X (PHYSICAL PROPERTIES)
Appearance and odor: Solder & flux paste with no characteristic odor.
SECTION XI (OPTIONAL INFORMATION)
IARC: International Agency for the Research on Cancer
ACGIH: American Conference of Governmental Industrial Hygienists
NIOSH: National Institute for Occupational Safety and Health
NTP: National Toxicology Program
PEL: Permissible Exposure Limit
OSHA: U.S. Occupational Safety and Health Administration
TLV: Threshold Limit Value
CAS: Chemical Abstracts Service Registry Number
Exposure limits are subject to change. Contact ACGIH, OSHA, NIOSH, and IARC for current values.
The information in this MSDS was obtained from sources we believe are reliable. However, this information is provided without any
representation or warranty, expressed or implied, regarding accuracy or correctness. The conditions or methods of handling, storage, use, and
disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons we do not assume responsibility
and expressly disclaim liability or loss, damage, or expense arising from it or in any way connected with the handling, storage, use, or disposal
of the product.
|