May 2008 Page 1 of 2
MATERIAL SAFETY DATA SHEET
MAY BE USED TO COMPLY WITH OSHA鈥橲 HAZARD COMMUNICATION STANDARD, 29 CFR 1910.1200 AND
SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT (SARA) OF 1986 PUBLIC LAW 99-499. STANDARD SHOULD BE
CONSULTED FOR SPECIFIC REQUIREMENTS.
SECTION I (IDENTIFICATION)
MANUFACTURER/ EUTECTIC CORPORATION TELEPHONE NUMBER:
SUPPLIERS NAME: N94 W14355 Garwin Mace Drive 1-800-558-8524
Menomonee Falls, WI 53051 USA
PRODUCT NAME: Eutectic 157
PRODUCT CLASSIFICATION: Solder Alloy
SECTION II (HAZARDOUS INGREDIENTS/IDENTITY INFORMATION)
IMPORTANT: This section covers the materials from which these products are manufactured. The fumes and gases produced during normal use of
these products are covered in Section V. The term "Hazardous" in "Hazardous Ingredients" should not only be interpreted as a term required and
defined in OSHA Hazard Communication Standard (29 CFR Part 1910.1200), but also as defined by other regulatory agencies. The chemicals or
compounds subject to reporting under Title III, in Section 313, of the Superfund Amendments and Reauthorization Act (SARA) are marked by the
symbol #.
WARNING: This product contains or produces a chemical known to the State of California to cause birth defects (or other reproductive harm) and
cancer. (California Health & Safety Code 25249.5 et seq.)
Exposure Limit (mg/m3)
CAS
INGREDIENTS NUMBER OSHA PEL ACGIH-TLV Percent Ingredients (by weight)
Tin 7440-31-5 2 2 60 鈥? 100
Silver # 7440-22-4 0.01 0.01 3鈥?7
SECTION III (PHYSICAL DATA)
Silver color, solid, no characteristic odor.
SECTION IV (FIRE AND EXPLOSION HAZARD DATA)
Nonflammable: Brazing flames can ignite combustibles. Refer to American National Standard Z49.1 for fire prevention during welding/brazing.
Rating under National Fire Protection 704: Health, 1; Flammability, 0; Reactivity, 0. Use CO2 or dry chemical extinguisher. Use NIOSH approved self-
contained breathing apparatus and full protective clothing if involved in fire. Finely divided dust may form explosive mixtures with air.
SECTION V (REACTIVITY DATA)
STABILITY: Stable Boiling Point: Tin: 2270 掳C
CONDITIONS TO AVOID: None Silver: 2210 掳C
INCOMPATIBILITY (Conditions to avoid): Strong acids/alkalis
HAZARDOUS POLYMERIZATION: will not occur.
Dust should be kept at a minimum. Brazing fumes cannot be classified simply. The composition and quantity of both are dependent upon the metal
being brazed, the process, procedure, and the filler material used. Other conditions which also influence the composition and quantity of the fumes and
gases to which workers may be exposed include: coatings on the metal being soldered (such as paint, plating, or galvanizing), the number of workers and
the volume of the work area, the quality and the amount of ventilation, position of the worker鈥檚 head with respect to the fume plume, as well as the
presence of contaminants in the atmosphere (such as chlorinated hydrocarbon vapors from cleaning and degreasing activities).
When the material is consumed, the fume and gas decomposition products generated are different in percent and form from the ingredients listed in
Section II. Fume and decomposition products, not the ingredients in the flux are important. Decomposition products include those originating from the
volatilization, reaction, or oxidation of materials in Section II, plus those from the base metal and coating, etc., as noted above. These components are
virtually always present as complex oxides and not as metals (Characterization of Arc Welding Fume: American Welding Society).
Monitor fume levels. One recommended way to determine the composition and quantity of fumes and gas to which workers are exposed is to take an air
sample in the worker's breathing zone (see ANSI/AWS F1.1, F1.2, F1.3, F1.4, and F1.5, available from the "American Welding Society," 550 N.W.
LeJeune Road, Miami, FL 33126).
SECTION VI (HEALTH HAZARD DATA)
Threshold Limit Value (TLV): The ACGIH recommended general limit for welding fume NOS (not otherwise specified) is 5 mg/m鲁. The ACGIH
1999 preface states: "The TLV-TWA should be used as guides in the control of health hazards and should not be used as firm lines between safe and
dangerous concentrations." See Section V for specific fume constituents that may modify the TLV.
MSDS: Eutectic 157 Page 2 of 2
EFFECTS OF OVEREXPOSURE - Brazing may create one or more of the following health hazards:
FUMES AND GASES can be dangerous to your health.
PRIMARY ROUTES OF ENTRY are the respiratory system. Other possible routes are eyes, ingestion, and/or skin contact.
PREEXISTING respiratory or allergic conditions may be aggravated in some individuals (i.e. asthma, emphysema).
SHORT TERM (ACUTE) OVEREXPOSURE to welding fumes may result in discomfort such as metal fume fever, dizziness, nausea, or dryness or
irritation of nose, throat, or eyes. PRIMARY ROUTE OF ENTRY is the respiratory system.
LONG TERM (CHRONIC) OVEREXPOSURE is believed by some investigators to affect pulmonary functions. PRIMARY ROUTE OF ENTRY
is the respiratory system.
See Section VII for precautions.
EMERGENCY & FIRST AID PROCEDURES: Call for medical aid. Employ first aid techniques recommended by The American Red Cross.
INHALATION: Remove to fresh air. If breathing is difficult, administer oxygen. If not breathing, begin artificial respiration.
If no detectable pulse, begin Cardiopulmonary Resuscitation. (CPR). Call for medical aid.
SKIN: Wash affected area with soap and water. If rash develops, see a physician.
EYES: Flush with a large amount of fresh water for at least 15 minutes. Get medical attention.
INGESTION: Seek medical attention.
CARCINOGENICITY
WELDING FUMES (not otherwise specified) are considered to be carcinogenic defined with no further categorization by NIOSH and IARC.
SECTION VII (PRECAUTION FOR SAFE HANDLING AND USE/APPLICABLE CONTROL MEASURES)
Steps to be taken if material is released or spilled: Sweep up.
Waste disposal method: Dispose of in accordance with all federal state, and local regulations.
SECTION VIII ( SPECIAL PROTECTION INFORMATION)
Read and understand the manufacturer's instructions and precautionary label on this product.
See American National Standard Z49.1, Safety in Welding and Cutting, published by the "American Welding Society," 550 N.W. LeJeune Road,
Miami, FL 33126 and OSHA Publication 2206 (29CFR 1910), U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954,
Pittsburgh, PA 15250-7954 for more detail on the following:
Ventilation: Use enough ventilation, local exhaust at the arc, or both, to keep the fumes and gases below the TLV's in the workers breathing
zone and the general area. Train the welder to keep his head out of the fumes. Monitor fume levels and do not exceed permissible exposure limits or
values.
Respiratory Protection: Use respirable fume respirator or air supplied respirator when brazing/welding in a confined space or where local exhaust or
ventilation does not keep exposure below the TLV's.
Eye Protection: Wear appropriate brazing glasses with side shield.
Protective Clothing: Wear head, hand, and body protection which help to prevent injury. See ANSI Z49.1.
Waste: Dispose of any grinding dust and waste residues in accordance with EPA or local regulations. Plastic containers and cardboard packaging can
be recycled.
Storage: Keep material sealed and dry before use. Keep remaining product sealed and dry.
Wash thoroughly after handling to remove all residue. Remove and professionally wash contaminated clothing before reuse.
SUPPLEMENTAL INFORMATION
IARC: International Agency for the Research on Cancer
ACGIH: American Conference of Governmental Industrial Hygienists
NIOSH: National Institute for Occupational Safety and Health
NTP: National Toxicology Program
PEL: Permissible Exposure Limit
OSHA: U.S. Occupational Safety and Health Administration
TLV: Threshold Limit Value
CAS: Chemical Abstracts Service Registry Number
Exposure limits are subject to change. Contact ACGIH, OSHA, NIOSH, and IARC for current values.
The information in this MSDS was obtained from sources we believe are reliable. However, this information is provided without any representation or
warranty, expressed or implied, regarding accuracy or correctness. The conditions or methods of handling, storage, use, and disposal of the product are
beyond our control and may be beyond our knowledge. For this and other reasons we do not assume responsibility and expressly disclaim liability of
loss, damage, or expense arising from it or any way connected with the handling, storage, use, or disposal of the product.
|