Updated May 29, 2007
Ozokerite Wax
Material Safety Data Sheet ( MSDS)
1. Product Identification 7. Hazards Identification
Product Name: Ozokerite Wax Eye: Solid material is not expected to be an eye irritant; however,
contact with molten wax may cause thermal burns. Vapors from
INCI Name: Ozokerite
molten wax may cause watering of the eyes.
Chemistry: Mineral
CAS Number: 8001-75-0 (EPA), #8021-55-4 (CTFA) Skin: Solid material is not expected to be a skin irritant; however
skin contact with molten wax may cause thermal burns. No harmful
EINECS Number:
effects from skin absorption are expected.
2. Physical & Chemical Properties Inhalation: Vapors emitted from molten wax are expected to have a
low degree of irritation by inhalation.
Melting Point: 164-169 F/73.3-76.1 C
Boiling Point: >650 F/343 C Ingestion: No harmful effects expected.
Non-Volatiles: negligible Signs and Symptoms: Effects of overexposure may include irrita-
tion of the nose and throat.
Viscosity: no data available
Specific Gravity: Approx. 0.96 Cancer: No data available.
Solubility in water: negligible Target Organs: No data available.
Refractive Index: no data available Developmental: No data available.
Appearance & Odor: White solid, none to slight/characteristic Pre-existing Medical Conditions: None known.
odor.
8. First Aid Measures
3. Stability & Reactivity Eyes: If irritation or redness develops from exposure to fumes gen-
erated during hot-melt processing operations, move victim away
Chemical Stability: Stable under normal conditions of storage and
handling. from exposure and into fresh air. Flush eyes with clean water. If
irritation or redness persists, seek medical attention. For contact with
Conditions to Avoid: Avoid all possible sources of ignition.
the molten material, gently open eyelids and flush affected area with
Incompatible Materials: Avoid contact with strong oxidizing agents.
cold water. Seek immediate medical attention.
Hazardous Decomposition Products: Combustion can yield major
amounts of oxides of carbon and minor amounts of oxides of sulfur and Skin: For contact with molten material, leave material on skin and
nitrogen. flush or immerse affected area using cold water. Seek medical atten-
tion.
Hazardous Polymerization: Will not occur.
Inhalation: If respiratory symptoms develop from exposure to fumes
emitted by the molten material, move victim away from source of
4. Handling & Storage
exposure and into fresh air. If symptoms persist, seek medical at-
Handling precautions: Wash thoroughly after handling. Do not wear
contaminated clothing or shoes. Use good personal hygiene practice. tention. If breathing difficulties should develop, oxygen should be
administered by qualified personnel. Seek immediate medical atten-
Storage Precautions: Keep containers tightly closed. Use and store
this material in cool, dry, well-ventilated areas away from heat and all tion.
sources of ignition. Store only in approved containers. Keep away from Ingestion: First aid is not normally required for the solid material;
any incompatible material. Protect containers against physical damage. however, if molten material is swallowed, seek immediate medical
attention.
Other Precautions: none specified
5. Accidental Release Measures 9. Fire Fighting Measures
This material may burn but will not ignite readily. Keep all sources of Flash Point: 400 F (COC) Minimum
ignition away from spill/release. Stay upwind and away from spill. Iso- Extinguishing Media: Dry chemical, foam, water, sand, or earth is
late danger area and keep unauthorized personnel out. Contain spill if it recommended.
can be done with minimal risk. Wear appropriate protective equipment, Fire Fighting Procedures: Emergency responders in the danger
including respiratory protection, as conditions warrant. Prevent spilled area should wear bunker gear and self contained breathing appara-
material from entering sewers, storm drains, other unauthorized treat- tus for fires beyond the incipient state. In addition, responders
ment drainage systems and natural waterways. Notify fire authorities should wear other appropriate protective equipment as conditions
and appropriate federal, state and local agencies. Cleanup under ex- warrant. Isolate danger area, keep unauthorized personnel out. Con-
pert supervision is advised. Minimize dust generation. Sweep up and tain spill if it can be done with minimal risk. Move undamaged con-
package appropriately for disposal. tainers from danger area if it can be done with minimal risk. With
water, cool equipment exposed to fire if it can be done with minimal
risk.
6. Exposure Controls & Personal Protection
Respiratory Protection: None required when working with the solid
material. If airborne concentrations of wax fumes, generated from mol- 10. Toxicological Information
ten wax, are expected, a NIOSH/MSHA approved air purifying respira- No definitive information available on carcinogenicity, mutagenicity,
tor with a dust/mist/fume filter may be used. target organs or developmental toxicity.
Protective Clothing: Not normally required for solid material. The use
of thermally-resistant gloves is recommended when there is a potential 11. Disposal Consideration
for exposure to molten wax. This material, if discarded as produced, is not a RCRA listed or
characteristic hazardous waste. Use which results in chemical or
Other Protective Measures: Approved eye protection to safeguard
against potential eye contact, irritation, or injury is recommended. A physical change or contamination may subject it to hazardous waste
source of clean water should be available in the work area for flushing regulations. Along with properly characterizing all waste materials,
eyes and skin. Impervious clothing should be worn as needed. consult state and local regulations regarding the proper disposal of
this material.
|