Search   
MSDS 
:
 Titanium(III) chloride, Al reduced, 98%
CAS 
:
 12003-13-3
SYNONYMS 
:
 None.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 12003-13-3 |Titanium(III) chloride | 98 | 234-421-8 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 14 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Reacts violently with water. Causes burns.Air
sensitive.Water-reactive.

Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
Causes gastrointestinal tract burns. The toxicological properties of
this substance have not been fully investigated.
Inhalation:
Causes chemical burns to the respiratory tract. The toxicological
properties of this substance have not been fully investigated.
Chronic:
Chronic exposure may cause effects similar to those of acute
exposure.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately. Do NOT allow victim to rub eyes or keep eyes closed.
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. If water-reactive products are embedded in the skin, no
water should be applied. The embedded products should be covered
with a light oil.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4
cupfuls of milk or water. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If breathing is difficult, give oxygen. Do NOT use
mouth-to-mouth resuscitation. If breathing has ceased apply
artificial respiration using oxygen and a suitable mechanical device
such as a bag and a mask.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Water
Reactive. Material will react with water and may release a flammable
and/or toxic gas. May ignite or explode on contact with steam or
moist air. May re-ignite after fire is extinguished.
Extinguishing Media:
Use dry sand or earth to smother fire. Use foam, dry chemical, or
carbon dioxide. DO NOT USE WATER! Contact professional fire-fighters
immediately.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Avoid generating dusty conditions. Provide
ventilation. Do not expose spill to water. Cover with dry earth, dry
sand, or other non-combustible material followed with plastic sheet
to minimize spreading and contact with water.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Do not allow water to get into the container because of violent
reaction. Do not breathe dust, vapor, mist, or gas. Do not get in
eyes, on skin, or on clothing. Keep container tightly closed. Do not
ingest or inhale. Do not allow contact with water. Use only in a
chemical fume hood. Discard contaminated shoes. Keep from contact
with moist air and steam.
Storage:
Store in a cool, dry place. Keep container closed when not in use.
Store in a tightly closed container. Keep away from water. Corrosives
area. Storage under a nitrogen blanket has been recommended.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Use explosion-proof ventilation equipment. Facilities storing or
utilizing this material should be equipped with an eyewash facility
and a safety shower. Use adequate ventilation to keep airborne
concentrations low.
Exposure Limits
CAS# 12003-13-3:
United Kingdom, WEL - TWA: (listed as aluminum, soluble salts): 2
mg/m3 TWA
United Kingdom, WEL - STEL: (listed as aluminum, soluble salts):
mg/m3 STEL

Belgium - TWA: (listed as aluminum, soluble salts): 2 mg/m3 VLE (
Al)
France - VME: (listed as aluminum, soluble salts): 2 mg/m3 VME
Germany: (listed as aluminum, soluble salts): 2 mg/m3 VME
Malaysia: (listed as aluminum, soluble salts): 2 mg/m3 TWA (as Al
Spain: (listed as aluminum, soluble salts): 2 mg/m3 VLA-ED (as Al

Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Powder
Color: purple
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: Not available.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: reacts
Specific Gravity/Density:
Molecular Formula: AlCl12Ti3
Molecular Weight: 596.12

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Combines vigorously or explosively with water. Air sensitive.
Material hydrolyzes in contact with moisture/water releasing toxic
and corrosive fumes of hydrogen chloride and aqueous hydrochloric
acid.
Conditions to Avoid:
Exposure to air, exposure to moist air or water.
Incompatibilities with Other Materials:
Oxidizing agents, active metals, alcohols, water.
Hazardous Decomposition Products:
Hydrogen chloride, chlorine, aluminum oxide, titanium/titanium
oxides.
Hazardous Polymerization: Will not occur.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 12003-13-3 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Titanium(III) chloride -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: WATER-REACTIVE SOLID, CORROSIVE, N.O.S.
Hazard Class: 4.3
UN Number: 3131
Packing Group: II
IMO
Shipping Name: WATER-REACTIVE SOLID, CORROSIVE, N.O.S.
Hazard Class: 4.3
UN Number: 3131
Packing Group: II
RID/ADR
Shipping Name: WATER-REACTIVE SOLID, CORROSIVE, N.O.S.
Hazard Class: 4.3
UN Number: 3131
Packing group: II

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 14 Reacts violently with water.
R 34 Causes burns.
Safety Phrases:
S 8 Keep container dry.
S 25 Avoid contact with eyes.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 12003-13-3: 1
Canada
CAS# 12003-13-3 is listed on Canada's NDSL List.
CAS# 12003-13-3 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 12003-13-3 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 6/30/1998 Revision #7 Date: 10/14/2004

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
1-CYANONAPHTHALENE, TECH. 86-53-3
1,4-DICYANO-2-BUTENE, 97% 1119-85-3
4-METHOXY-2-METHYLANILINE, 98% 102-50-1
Perchloromethyl mercaptan, 97% 594-42-3
2,4,5-Trichloroaniline, tech., 97% 636-30-6
2,4,6-Trimethylphenol, 99% 527-60-6
n-Undecyl cyanide, 94% 2437-25-4
2-Methoxy-5-methylaniline, 95% 120-71-8
4-Chloro-o-phenylenediamine, 96% 95-83-0
2-[4-(4-Dimethylaminophenyl)-1,3-butadieny 8903-71-1
Hexachloro-1,3-butadiene, 98% 87-68-3
p-Nitrosophenol 104-91-6
STEARONITRILE TECHN. 90+% 638-65-3
Fumaronitrile, 98% 764-42-1
2-Thiopheneacetonitrile, tech., 94% 20893-30-5
Bis(carboxymethyl) trithiocarbonate, 98% 6326-83-6
5-METHOXY-1,3,4-TRIPHENYL-4,5-DIHYDRO-1H-1,2,4-TRIAZOLIN 0-01-1
3,3'-Thiodipropionitrile 111-97-7
Methylenaminoacetonitrile, 98% 109-82-0
2,2,4,4,6,8,8-Heptamethylnonane, 98% 4390-04-9
N-(2-Aminoethyl)pyrrolidine, 99% 7154-73-6
4-Chloro-2-methoxy-5-methylaniline, tech., 85% 6376-14-3
3-Chloro-4-nitroaniline, 97% 825-41-2
2-Chloro-1,3,2-dioxaphospholane, 97% 822-39-9
Tetraisopropylthiuram disulfide, 98% 4136-91-8
6-Hydroxyflavone 6665-83-4
7-Hydroxyflavone 6665-86-7
2-Chloro-1,4-benzoquinone, 95% 695-99-8
2,6-Dimethoxy-1,4-benzoquinone, 97% 530-55-2
2'-Hydroxy-5'-methoxyacetophenone, 99% 705-15-7
6-NITROINDOLINE 19727-83-4
2-Chlorophenol, 98+% 95-57-8
3,4,5,6-TETRACHLOROPHTHALIMIDE 1571-13-7
Diethyl(phthalimidomethyl)phosphonate, 97% 33512-26-4
4-Butoxy-2-nitroaniline, 99% 3987-86-8
4-Chloro-1,2-phenylenediamine, 97% 95-83-0
Silica gel, 3-6 mm, pore diameter ca. 9 nm 7631-86-9
Ethylenediaminetetraacetic acid dicopper salt, tetrahydrate, 98% 39208-15-6
Diphenylselenium dichloride, 97% 2217-81-4
2-Bromostearonitrile 0-01-1
4-Chlorophenyl methyl sulfide, 98% 123-09-1
N-Cyclohexylaniline, 98% 1821-36-9
3-Amino-4-chlorobenzenesulfonic acid hydrate, 97% 98-36-2
2-Hexenedinitrile 13042-02-9
4-Methylsulphonylbenzyl bromide, tech, 75-80% 53606-06-7
L-1,2,3,4-Tetrahydroisoquinoline-3-Carboxylic Acid, 98% 74163-81-8
Titanium(III) chloride, Al reduced, 98% 12003-13-3
Ethyl-3-Indoleacetate, 99% 778-82-5
1-Acetylindole, 98% 576-15-8
5-Fluoroindole-2-carboxylic acid, 98% 399-76-8

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net