non-hazardous ients volatile organic compounds: neglig levels of voc emissions are expected ing 2:hydrocarbons may be emitted at application temp. emissions data is other prot equip:provide a cold water source for burn treatment.
HB FULLER CO -- HOT MELT ADHESIVE, 00-0710
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CGQFF
MSDS NAME: HOT MELT ADHESIVE, 00-0710
Responsible Party
Name: HB FULLER CO
Address: 3530 LEXINGTON AVE N
City: ST PAUL MN 55126-8076
Info Phone: 612-481-3300
Emergency Phone Number: 800-228-5635;800-424-9300(CHEMTREC)
Published: Y
=======================================================
Contractor Summary
=======================================================
Name: H B FULLER COMPANY
Address: 3530 LEXINGTON AVENUE N
City: ST PAUL MN 55126-8076
Phone: 888-853-1758/651-236-5300
Name: HB FULLER CO
Address: 1200 WOLTERS BLVD
City: VADNAIS HEIGHTS MN 55110
Phone: 612-481-3300
=======================================================
Ingredients
=======================================================
Name: NON-HAZARDOUS INGREDIENTS
OSHA PEL: N/K (FP N)
ACGIH TLV: N/K (FP N)
-----------------------------
RTECS #: 9999999VO
Name: VOLATILE ORGANIC COMPOUNDS: NEGLIG LEVELS OF VOC EMISSIONS ARE EXPECTED
AT AMBIENT TEMP & PRESS. LOW MOLECULAR WT
-----------------------------
Name: ING 2:HYDROCARBONS MAY BE EMITTED AT APPLICATION TEMP. EMISSIONS DATA IS
BEST DEVEL BY MONITORING ACTUAL PLANT CNDTNS.
-----------------------------
Name: OTHER PROT EQUIP:PROVIDE A COLD WATER SOURCE FOR BURN TREATMENT.
=======================================================
Health Hazards Data
=======================================================
LD50 LC50 Mixture: NONE SPECIFIED BY MANUFACTURER.
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: YES
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Effects of Exposure: ACUTE:EYES:VAPORS AND FUMES RELEASED AT OR ABOVE
APPLICATION TEMPERATURES MAY CAUSE IRRITATION. SKIN:CONTACT WITH MOLTEN
MATERIAL WILL CAUSE BURNS. INHALATION:VAPORS AND FUMES MAY CAUSE IRRITATION
OF THE NOSE, THROAT AND RESPIRATORY TRACT.OVEREXPOSURE MAY CAUSE HEADACHES
AND DIZZINESS. INGESTION:NOT (EFTS OF OVEREXP)
Explanation Of Carcinogenicity: NOT RELEVANT
Signs And Symptions Of Overexposure: HLTH HAZ:AN ANTICIPATED ROUTE OF EXPOSURE.
SMALL AMOUNTS ARE NOT ANTICIPATED TO BE HARMFUL. CHRONIC:NO ANTICIPATED
CHRONIC EFFECTS.
Medical Cond Aggravated By Exposure: NO KNOWN EFFECTS ON OTHER ILLNESSES.
First Aid: EYES:IMMED FLUSH W/POTABLE WATER FOR MIN OF 15 MINS, SEEK ASSISTANCE
FROM MD (FP N). INHAL:REMOVE SUBJECT TO FRESH AIR. CALL MD IF SYMPS PERSIST.
INGEST:IF PERS CAN SWALLOW, GIVE 1 GLASS OF WATER/MILK . DO NOT INDUCE VOMIT.
GET IMMED MED ATTN. NEVER GIVE ANYTHING BY MOUTH TO UNCON PERS. SKIN:FOR
BURNS:IMMERSE CONT AREA IMMED IN COLD, CLEAN WATER. DO NOT ATTEMPT TO REMOVE
SET PROD. REMOVAL (SUPDAT)
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: ALLOW TO SOLIDIFY AT ROOM TEMPERATURE, SCRAPE UP
& PLACE IN DISPOSAL CONTAINER.
Neutralizing Agent: NONE SPECIFIED BY MANUFACTURER.
Waste Disposal Methods: DISP MUST BE I/A/W FED, STATE & LOC REGS(FP N). TO
THE BEST OF MFR'S KNOWLEDGE, THIS PROD DOES NOT MEET DEFINITION OF HAZ WASTE
UNDER U.S. EPA HAZ WASTE REGS 40 CFR 261. DISP OF IN APPRVD LANDFILL. CO
NSULT STATE, LOC/PROVINCIAL AUTHS FOR MORE(SUPDAT)
Handling And Storage Precautions: AVOID BREATHING VAPORS/FUMES OF HEATED
PRODUCT. PREVENT CONTACT W/MOLTEN PRODUCT.
Other Precautions: CONSULT TECHNICAL DATA SHEET FOR SPECIFIC STORAGE
INSTRUCTIONS.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Flash Point Method: COC
Flash Point Text: >400F,>204C
Extinguishing Media: CARBON DIOXIDE, DRY CHEMICAL, CHEMICAL FOAM OR WATER FOG.
USING A DIRECT, STRAIGHT WATER STREAM MAY TEND TO SPREAD FIRE.
Fire Fighting Procedures: USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT (FP N). AVOID USING DIRECT STRAIGHT WATER STREAM ON MOLTEN MATL TO
REDUCE SPLATTERING & SPREADING OF FIRE.
Unusual Fire/Explosion Hazard: NONE KNOWN.
=======================================================
Control Measures
=======================================================
Respiratory Protection: NOT NORMALLY REQUIRED. USE NIOSH APPROVED RESPIRATOR IF
CONDITIONS WARRANT.
Ventilation: HOT MELTS SHOULD BE USED W/GOOD VENT. AT APPLICATION TEMP USE OF
LOC EXHST OVER PREMELTING RESERVOIR IS ENCOURAGED.
Protective Gloves: THERMALLY PROTECTIVE GLOVES.
Eye Protection: ANSI APPROVED CHEM WORKERS GOGGS (FP N).
Other Protective Equipment: ANSI APPRVD EYE WASH FOUNTAIN & DELUGE SHOWER (FP
N). AT ELEVATED TEMPS PVNT CONT BY WEARING LONG SLEEVED SHIRT.
Work Hygienic Practices: NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health: FIRST AID PROC:COULD RSLT IN SEV TISS DMG.
COVER CONT AREA W/CLEAN WET COMPRESSES & TAKE SUBJECT TO MD IMMED. NOTE
TO MD:MATL SHOULD NOT BE FORCIBLY PULLED FROM SKIN. MINERAL OIL MAY BE USED
TO LOOSEN MATL. WASTE DISP METH:RESTRICTIVE REQUIREMENTS.
=======================================================
Physical/Chemical Properties
=======================================================
Spec Gravity: 0.98
Appearance and Odor: SOLID, CHARACTERISTIC COLOR; NEUTRAL ODOR.
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: NONE SPECIFIED BY MANUFACTURER.
Materials To Avoid: NOT ESTABLISHED.
Hazardous Decomposition Products: HAZARDOUS COMBUSTION PRODUCTS:INCOMPLETE
COMBUSTION CAN YIELD LOW MOLECULAR WEIGHT HYDROCARBONS, CARBON MONOXIDE.
Hazardous Polymerization Indicator: NO
Conditions To Avoid Polymerization: NOT RELEVANT
=======================================================
Toxicological Information
=======================================================
=======================================================
Ecological Information
=======================================================
=======================================================
MSDS Transport Information
=======================================================
=======================================================
Regulatory Information
=======================================================
=======================================================
Other Information
=======================================================
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: HOT MELT ADHESIVE, 00-0710
Assigned IND: Y
Company: HB FULLER CO
Street: 1200 WOLTERS BLVD
City: VADNAIS HEIGHTS MN
Zipcode: 55110
Health Emergency Phone: 800-228-5635;800-424-9300(CHEMTREC)
Label Required IND: Y
Date Of Label Review: 02/24/1998
Status Code: C
Label Date: 02/24/1998
Origination Code: G
Eye Protection IND: YES
Skin Protection IND: YES
Signal Word: WARNING
Respiratory Protection IND: YES
Health Hazard: Moderate
Contact Hazard: Moderate
Fire Hazard: Slight
Reactivity Hazard: None
Hazard And Precautions: COMBUSTIBLE. ACUTE:EYES:VAPORS AND FUMES RELEASED AT OR
ABOVE APPLICATION TEMPERATURES MAY CAUSE IRRITATION. SKIN:CONTACT WITH MOLTEN
MATERIAL WILL CAUSE BURNS. INHALATION:VAPORS AND FUMES MAY CAUSE I RRITATION
OF THE NOSE, THROAT AND RESPIRATORY TRACT. OVEREXPOSURE MAY CAUSE HEADACHES
AND DIZZINESS. CHRONIC:NONE LISTED BY MANUFACTURER.
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.