DUTCH BOY PAINTS -- FE-501 GLOSS BLACK FRESH & EASY SPRAY ENAMEL
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CLBTR
MSDS NAME: FE-501 GLOSS BLACK FRESH & EASY SPRAY ENAMEL
Responsible Party
Name: DUTCH BOY PAINTS
Box: 6709
City: CLEVELAND OH 44101
Info Phone: (216) 566-2902
Emergency Phone Number: 216-566-2917
Review Ind: Y
Published: Y
=======================================================
Contractor Summary
=======================================================
Name: DUTCH BOY PAINTS
Box: 6709
City: CLEVELAND OH 44101
Phone: (216) 566-2902
=======================================================
Ingredients
=======================================================
Cas: 74-98-6
RTECS #: TX2275000
Name: PROPANE
Percent by Wt: 14.
OSHA PEL: 1000 PPM
------------------------------
Cas: 106-97-8
RTECS #: EJ4200000
Name: BUTANE
Percent by Wt: 13.
OSHA PEL: 800 PPM
ACGIH TLV: 800 PPM
ACGIH STEL: NOT ESTABLISHED
------------------------------
Cas: 100-41-4
RTECS #: DA0700000
Name: ETHYLBENZENE
Percent by Wt: 3.
OSHA PEL: 100 PPM
ACGIH TLV: 100 PPM
ACGIH STEL: 543 MG/M3;125 PPM
EPA Rpt Qty: 1000 LBS
DOT Rpt Qty: 1000 LBS
------------------------------
Cas: 1330-20-7
RTECS #: ZE2100000
Name: XYLENE
Percent by Wt: 15.
OSHA PEL: 100 PPM
ACGIH TLV: 100 PPM
EPA Rpt Qty: 1000 LBS
DOT Rpt Qty: 1000 LBS
------------------------------
Cas: 67-64-1
RTECS #: AL3150000
Name: ACETONE
Percent by Wt: 47.
OSHA PEL: 750 PPM
ACGIH TLV: 750 PPM
EPA Rpt Qty: 5000 LBS
DOT Rpt Qty: 5000 LBS
=======================================================
Health Hazards Data
=======================================================
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: NO
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Signs And Symptions Of Overexposure: IRRITATION OF EYES, SKIN AND RESPIRATORY
SYSTEM. MAY CAUSE NERVOUS SYSTEM DEPRESSION. EXTREME OVEREXPOSURE MAY
RESULT IN UNCONSCIOUSNESS AND POSSIBLY DEATH. HEADACHE, DIZZINESS, NAUSEA,
AND LOSS OF COORDINATION ARE INDICATIONS OF EXCESSIVE EXPOSURE TO VAPORS OR
SPRAY MISTS. REDNESS AND ITCHING OR BURNING SENSATION MAY INDICATE EYE OR
EXCESSIVE SKIN EXPOSURE.
Medical Cond Aggravated By Exposure: NONE GENERALLY RECOGNIZED.
First Aid: INHALATION: IF AFFECTED, REMOVE FROM EXPOSURE. RESTORE BREATHING.
KEEP WARM AND QUIET. SKIN: WASH AFFECTED AREA THOROUGHLY WITH SOAP AND
WATER. REMOVE CONTAMINATED CLOTHING AND LAUNDER BEFORE RE-U SE. EYES: FLUSH
EYES WITH LARGE AMOUNTS OF WATER FOR 15 MINUTES. GET MEDICAL ATTENTION.
INGESTION: NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. DO NOT
INDUCE VOMITING. GIVE SEVERAL GLAS SES OF WATER AND SEEK MEDICAL ATTENTION.
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: REMOVE ALL SOURCES OF IGNITION. VENTILATE AND REMOVE
WITH INERT ABSORBENT.
Waste Disposal Methods: WASTE FROM THESE PRODUCTS MAY BE HAZARDOUS AS DEFINED
UNDER THE RESOURCE CONSERVATION AND RECOVERY ACT 40 CFR 261. WASTE MUST BE
TESTED FOR IGNITABILITY TO DETERMINE THE APPLICABLE EPA HAZARDOUS WAST E
NUMBERS. DO NOT INCINERATE. DEPRESSURIZE CONTAINER. DISPOSE OF IN
ACCORDANCE WITH FEDERAL, STAT E, AND LOCAL REGULATIONS REGARDING POLLUTION.
Handling And Storage Precautions: CONTENTS ARE EXTREMELY FLAMMABLE. KEEP AWAY
FROM HEAT, SPARKS, AND OPEN FLAME. VAPORS WILL ACCUMULATE READILY AND MAY
IGNITE EXPLOSIVELY. DURING USE AND UNTIL ALL VAPORS ARE GONE: KEEP AREA
VENTILA TED-DO NOT SMOKE-EXTINGUISH ALL FLAMES, PILOT LIGHTS, AND
HEATERS-TURN OFF STOVES, ELECTRIC TOOLS.
Other Precautions: CONSULT NFPA CODE. USE APPROVED BONDING AND GROUNDING
PROCEDURES. CONTENTS UNDER PRESSURE. DO NOT PUNCTURE, INCINERATE, OR EXPOSE
TO TEMPERATURE ABOVE 120 F. HEAT FROM SUNLIGHT, RADIATORS, STOVES, HOT
WATER. INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING AND INHALING THE
CONTENTS CAN BE HARMF UL OR FATAL.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Flash Point Method: PMCC
Flash Point: <-17.6C, 0.F
Lower Limits: 0.7
Upper Limits: 12.8
Extinguishing Media: CARBON DIOXIDE, DRY CHEMICAL, FOAM
Fire Fighting Procedures: FULL PROTECTIVE EQUIPMENT INCLUDING SELF-CONTAINED
BREATHING APPARATUS SHOULD BE USED. WATER SPRAY MAY BE INEFFECTIVE. IF
WATER IS USED, FOG NOZZLES ARE PREFERABLE. WATER MAY BE EXPLOSION WHEN EXPO
SED TO EXTREME HEAT.
Unusual Fire/Explosion Hazard: CLOSED CONTAINERS MAY EXPLODE WHEN EXPOSED TO
EXTREME HEAT.
=======================================================
Control Measures
=======================================================
Respiratory Protection: IF PERSONAL EXPOSURE CANNOT BE CONTROLLED BELOW
APPLICABLE LIMITS BY VENTILATION, WEAR A PROPERLY FITTED ORGANIC
VAPOR/PARTICULATE RESPIRATOR APPROVED BY NIOSH/MSHA FOR PROTECTION AGAINST
MATERIALS IN SECTION II. WHEN SANDING OR ABRADING THE DRIED FILM,WEAR A
DUST/MIST RESPIRATOR APPROVED BY NIOSH/MSHA FOR PROTECTION AGAINST
NON-VOLATILE MATERIALS IN SECT II
Ventilation: LOCAL EXHAUST PREFERABLE. GENERAL EXHAUST ACCEPTABLE IF THE
EXPOSURE TO MATERIALS IN SEC II IS MAINTAINED BELOW APPLICABLE EXPOSURE
LIMITS.
Protective Gloves: WEAR GLOVES WHICH ARE RECOMMENDED BY GLOVE SUPPLIER FOR
PROTECTION
Eye Protection: WEAR SAFETY SPECTACLES WITH UNPERFORATED SIDESHIELDS.
Work Hygienic Practices: WASH HANDS AFTER USING.
Supplemental Safety and Health: NFPA CODE 30B: LEVEL 3 AEROSOLS RED LABEL:
EXTREMELY FLAMMABLE, FLASH BELOW 21 F USE WITH ADEQUATE VENTILATION. AVOID
BREATHING VAPOR AND SPRAY MIST. AVOID CONTACT WITH SKIN AND EYES. RA
TING: HEALTH=2;FLAMMABILITY=4;REACTIVITY=0
=======================================================
Physical/Chemical Properties
=======================================================
B.P. Text: <0-600F
Vapor Density: >AIR
Volatile Org Content %: 45
Evaporation Rate & Reference: FASTER THAN ETHER
Percent Volatiles by Volume: >75
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: NONE KNOWN.
Materials To Avoid: NONE KNOWN.
Hazardous Decomposition Products: BY FIRE: CARBON DIOXIDE, CARBON MONOXIDE,
OXIDES OF METALS IN SECTION II.
Hazardous Polymerization Indicator: NO
=======================================================
Toxicological Information
=======================================================
Toxicological Information: PROLONGED OVEREXPOSURE TO SOLVENT INGREDIENTS IN
SECTION II MAY CAUSE ADVERSE EFFECTS TO THE LIVER, URINARY, BLOOD-FORMING,
CARDIOVASCULAR, AND REPRODUCTIVE SYSTEMS. RATS EXPOSED TO TITANIUM DIOXIDE
DUST AT 250 MG/M3 DEVELOPED LUNG CANCER, HOWEVER, SUCH EXPOSURE LEVELS ARE
NOT ATTAINABLE IN THE WORKPLACE. REPORTS HAVE ASSOCIATED REPEATED AND
PROLONGED OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAI N AND NERVOUS SYSTEM
DAMAGE.
=======================================================
Ecological Information
=======================================================
=======================================================
MSDS Transport Information
=======================================================
=======================================================
Regulatory Information
=======================================================
Sara Title III Information: ETHYLBENZENE, XYLENE
Federal Regulatory Information: TSCA CERTIFICATION: ALL CHEMICALS IN THIS
PRODUCT ARE LISTED, OR ARE EXEMPT FROM LISTING, ON THE TSCA INVENTORY.
State Regulatory Information: CALIFORNIA PROPOSITION 65: THESE PRODUCTS CONTAIN
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
=======================================================
Other Information
=======================================================
Other Information: THE ABOVE INFORMATION PERTAINS TO THESE PRODUCTS AS
CURRENTLY FORMULATED, AND IS BASED ON THE INFORMATION AVAILABLE AT THIS TIME.
ADDITION OF REDUCERS OR OTHER ADDITIVES TO THESE PRODUCTS MAY SUBSTAN TIALLY
ALTER THE COMPOSITION AND HAZARDS OF THE PRODUCTS. SINCE CONDITIONS OF USE
ARE OUTSIDE OUR CONTROL, WE MAKE NO WARRANTIES, EXPRESS OR IMPLIED, AND
ASSUME NO LIABILITY IN CONNECTION WITH ANY US E OF THIS INFORMATION.
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: FE-501 GLOSS BLACK FRESH & EASY SPRAY ENAMEL
Assigned IND: Y
Company: DUTCH BOY PAINTS
PO Box: 6709
City: CLEVELAND OH
Zipcode: 44101
Health Emergency Phone: 216-566-2917
Label Required IND: Y
Date Of Label Review: 04/16/2001
Status Code: A
Origination Code: G
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
PVC GRAY CEMENT, UNI-WELD SERIES 1600, 1700, 1800, 1900
| 109-99-9
78-93-3
108-94-1
9002-86-2
112945-52-5
67-64-1 |
|
PVC GRAY CEMENT,CHEM-TECH:5500;5600
| 109-99-9
78-93-3
108-94-1
9002-86-2
112945-52-5
67-64-1 |
|
SAFTEY MATCH
| |
|
FLASHBREAKER 1
| |
|
REGENT RUBBER STAMP INK RED
| |
|
CODING & MARKING INK 4134, BLACK,WHITE,BLUE,GRAY,BRONZE
| |
|
CODING & MARKING INK 4134, BLACK,WHITE,BLUE,GRAY,BRONZE
| |
|
SO SURE STENCIL INK RED
| 67-64-1
74-98-6
108-88-3
8032-32-4
106-97-8
75-28-5
1330-20-7
100-41-4 |
|
SO SURE STENCIL INK WHITE
| 67-64-1
74-98-6
108-88-3
8032-32-4
106-97-8
75-28-5
1330-20-7 |
|
SO SURE STENCIL INK YELLOW
| 67-64-1
74-98-6
108-88-3
106-97-8
75-28-5
1330-20-7
123-86-4
8006-39-1 |
|
CORRECTION FLUID
| 71-55-6
61788-76-9 |
|
PIGMENT ONE INKED RIBBONS FOR MATRIX
| |
|
4134 CODING AND MARKING INK YELLOW
| |
|
PVC GREY CEMENT,PLASTI-WELD SERIES:203,403
| 109-99-9
78-93-3
108-94-1
9002-86-2
112945-52-5
67-64-1 |
|
2023STRATA BLUE INK MARKING
| |
|
X STAMPER INK XLR-20 WHITE
| |
|
X STAMPER INK XLR-20 WHITE
| |
|
FRAME FAST 280 ADHESIVE
| 7085-85-0 |
|
FRAME FAST AEROSOL ACTIVATOR 304
| 67-64-1
106-97-8
74-98-6 |
|
FIREPOWER FP-10 LUBRICANT ELITE
| |
|
BABY POWDER
| |
|
MIL-PRF-87257A, MLS 97-057
| 128-37-0
29385-43-1
1330-20-7 |
|
FINGERTIP MOISTENER
| |
|
IBM, BLACK NYLON RIBBON
| 32131-17-2
8005-02-5
1325-86-6
548-62-9
6358-85-6
112-80-1
1333-86-4 |
|
SO-SURE WHITE 37875 (54-370) P ENAMEL
| 74-98-6
106-97-8
108-88-3
67-64-1
64475-85-0
75-28-5 |
|
SO-SURE CORROSION PREVENTION COMPOUND
| 67-63-0
811-97-2
8032-32-4
8030-30-6
78-83-1
107-98-2
108-88-3
71-36-3
64741-65-7
64741-97-5
25619-56-1 |
|
PITT PENN PREMIUM HEAVY DUTY MILITARY (SEE SUPPL DATA)
| |
|
V.O.C. COMPLIANT SPRAY PAINT ( AEROSOL )
| 1330-20-7
74-98-6
115-10-6
110-12-3
107-87-9
108-10-1
95-63-6
71-36-3
64742-95-6 |
|
FORMULA 2500 OVEN CLEANER 6221-6
| |
|
SCOTCH-WELD (TM) DP-100 NS (PART A) TRANSLUCENT EPOXY ADHESI
| |
|
SCOTH-WELD (TM) DP-100 NS (PART B) TRANSLUCENT EPOXY ADHESIV
| |
|
AC-236 CLASS B BASE
| |
|
AC-236 ACCELERATOR
| |
|
PITT PENN PREMIUM HEAVY DUTY MILITARY ANTIFREEZE, PREMIXED
| |
|
PITT PENN PREMIUM HEAVY DUTY MILITARY ANTIFREEZE, PREMIXED
| |
|
PITT PENN PREMIUM HEAVY DUTY MILITARY ANTIFREEZE
| |
|
DINITROL AV 30
| |
|
CARBON DIOXIDE GAS
| |
|
DEMAND CS
| |
|
81878 101BR ULTRA COPPER HIGH TEMP RTV SILICONE GASKET MAK
| 70131-67-8
63148-62-9
68611-44-9
2224-33-1
12001-26-2
23843-64-3
96-29-7
1309-37-1 |
|
POLYURETHANE AEROSOL COLORS
| 123-86-4
1330-20-7
8052-41-3
67-64-1
74-98-6
75-28-5
106-97-8 |
|
GARD ANTI RUST SAE 30
| |
|
5506331 MOLYDAG 254
| |
|
DP40 NON SANDING EPOXY PRIMER
| 107-98-2
108-88-3
110-19-0
11103-86-9
1330-20-7
1333-86-4
13463-67-7
14807-96-6
25068-38-6
25086-48-0
67-63-0
7727-43-7
7789-06-2
78-93-3
90438-79-2 |
|
ACMI #4134 CODING & MARKING INK
| |
|
STAR SOLV
| |
|
PRO-SEAL 870 A-2 BASE 0870A65
| 28470-78-2
13463-67-7
1317-65-3
108-88-3
68611-50-7 |
|
HEL-CAT #5D625302
| |
|
FE-501 GLOSS BLACK FRESH & EASY SPRAY ENAMEL
| 74-98-6
106-97-8
100-41-4
1330-20-7
67-64-1 |
|
CRYSTAL SIMPLE GREEN
| 111-76-2 |
|
|