Search   
MSDS  : AXAREL 6000
CAS  : 64742-47-8
NAME  : mixed aliphatic hydrocarbons
PETROFERM INC. -- AXAREL 6000
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CLQLH
MSDS NAME: AXAREL 6000
Responsible Party
Name: PETROFERM INC.
Address: 5415 FIRST COAST HIGHWAY
City: FERNANDINA BEACH FL 32034
Info Phone: 904-261-8286
Emergency Phone Number: 904-261-8286;703-527-3887
=======================================================
Ingredients
=======================================================
Cas: 64742-47-8
RTECS #: OA5504000
Name: MIXED ALIPHATIC HYDROCARBONS
% low Wt: 98.
% high Wt: 100.
OSHA PEL: 500 PPM
ACGIH TLV: NOT EST.
=======================================================
Health Hazards Data
=======================================================
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: YES
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Effects of Exposure: SEE SIGNS AND SYMPTOMS OF OVEREXPOSURE (FP N).
Signs And Symptions Of Overexposure: INHALATION: MAY CAUSE IRRITATION OF THE
UPPER RESPIRATORY TRACT. INGESTION: MAY CAUSE IRRITATION OF THE MOUTH, THROAT
AND GASTROINTESTINAL TRACT WITH NONSPECIFIC DISCOMFORT SUCH AS NAUSEA,
HEADACHE, D IARRHEA, THIRST, AND WEAKNESS. SKIN: MAY CAUSE IRRITATION.
SIGNIFICANT SKIN PERMEATION AND SYSTEMIC TOXICITY AFTER CONTACT APPEAR
UNLIKELY. EYES: LIQUID VAPOR CONTACT MAY CAUSE EYE IRRITATION WITH TEA RING
OR BLURRING OF VISION.
First Aid: INHALATION: REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL
RESPIRATION. IF BREATHINGG IS DIFFICULT, GIVE OXYGEN. CONSULT PHYSICIAN.
INGESTION: DO NOT INDUCE VOMITING. IMMEDIATELY GIVE TWO GLAS SES OF WATER.
SEEK MEDICAL ATTENTION. SKIN: REMOVE CONTAMINATED CLOTHING. THOROUGHLY WASH
AFFECTED AREA WITH SOAP AND WATER; USE SKIN CREAM IF IRRITATION IS SEVERE.
EYES: IMMEDIATELY FLUSH WITH WATER FOR AT LEAST 15 MINUTES. CALL PHYSICIAN
IF IRRITATION PERSISTS.
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: ABSORB SPILL WITH INERT MATERIAL, THEN PLACE IN
CHEMICAL WASTE CONTAINER. FOR LARGE SPILLS, DIKE FOR LATER DISPOSAL. OBSERVE
GOVERNMENT REGULATIONS.
Neutralizing Agent: N/P.
Waste Disposal Methods: WASTE TREAT OR INCINERATE USED MATERIAL IN COMPLIANCE
WITH ALL APPLICABLE FEDERAL, STATE AND LOCAL REGULATIONS.
Handling And Storage Precautions: STORE IN ORIGINAL CONTAINER, PREFERABLY IN A
COOL, VENTILATED, FIRE-RESISTANT BUILDING. AVOID OVERHEATING OR FREEZING.
Other Precautions: SINCE EMPTY CONTAINERS MAY RETAIN PRODUCT RESIDUES (VAPOR,
LIQUID, OR SOLID) ALL LABEL PRECAUTIONS MUST BE OBSERVED.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Flash Point Method: PMCC
Flash Point: =62.8C, 145.F
Lower Limits: 1.0
Upper Limits: 6.0
Extinguishing Media: DRY CHEMICAL, CHEMICAL FOAM, CARBON DIOXIDE. CLASS BC, ABC
FIRE EXTINGUISHER.
Fire Fighting Procedures: NIOSH APPROVED SELF-CONTAINED POSITIVE PRESSURE
BREATHING APPARATUS AND PROTECTIVE CLOTHING SHOULD BE WORN IN FIGHTING FIRES
INVOLVING CHEMICALS.
Unusual Fire/Explosion Hazard: NONE KNOWN.
=======================================================
Control Measures
=======================================================
Respiratory Protection: USE NIOSH APPROVED RESPIRATOR IF VENTILATION IS NOT
SUFFICIENT AND IF MISTS ARE GENERATED.
Ventilation: IF DESIRABLE TO REDUCE ODOR, MECHANICAL (GENERAL) VENTILATION
SHOULD HAVE AN AIRFLOW OF 55 CFM. LOCAL EXHAUST CAN ALSO (SUPPLEMENTAL
SAFETY)
Protective Gloves: CHEMICAL RESISTANT GLOVES SHOULD BE WORN WITH ALL INDUSTRIAL
CHEMICALS.
Eye Protection: ANSI APPROVED CHEMICAL SAFETY GOGGLES (FP N).
Other Protective Equipment: EYEWASH AND DELUGE SHOWER MEETING ANSI DESIGN
CRITERIA (FP N).
Work Hygienic Practices: N/P.
Supplemental Safety and Health: VENTILATION (CON'T): BE EFFECTIVE IN MINIMIZING
ODOR. PHYSICAL/CHEMICAL PROPERTIES (CON'T): % VOLATILE (BY WEIGHT): NOT
DETERMINED.
=======================================================
Physical/Chemical Properties
=======================================================
Boiling Point: =182.2C, 360.F
B.P. Text: 360-440F (182-227C)
Vapor Pres: 1.10 MM HG (25C)
Vapor Density: 6.2
Spec Gravity: 0.81 @ 77F (25C)
Evaporation Rate & Reference: NOT DETERMINED
Solubility in Water: INSOLUBLE
Appearance and Odor: CLEAR, COLORLESS LIQUID WITH MILD HYDROCARBON ODOR.
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: TEMPERATURES ABOVE 360F (182C). KEEP AWAY FROM
HEAT, SPARKS, FLAMES.
Materials To Avoid: STRONG OXIDIZING AGENTS, STRONG ACIDS, STRONG BASES.
Hazardous Decomposition Products: NONE, OTHER THAN NORMAL PRODUCTS OF
COMBUSTION.
Hazardous Polymerization Indicator: NO
Conditions To Avoid Polymerization: WILL NOT OCCUR.
=======================================================
Toxicological Information
=======================================================
Toxicological Information: MIXED ALIPHATIC HYDROCARBON: LD50 ORAL RAT: 39,900
MG/KG. LD50 DERMAL RABBIT: 4,000 MG/KG. LC50 INHALATION (1 HR., RAT): 724.1
MG/L.
=======================================================
Ecological Information
=======================================================
Ecological: NO INFORMATION AVAILABLE.
=======================================================
MSDS Transport Information
=======================================================
Transport Information: NON-REGULATED.
=======================================================
Regulatory Information
=======================================================
Sara Title III Information: NO COMPONENTS OF AXAREL 6000 APPEARS ON SARA 313
TOXIC CHEMICALS LIST (40 CFR 372.65).
Federal Regulatory Information: NO COMPONENTS OF AXAREL 6000 APPEARS ON ANY OF
EPA'S LISTS OF TOXIC OR HAZARDOUS SUBSTANCES. ALL COMPONENTS OF PRODUCT
LISTED ON TSCA INVENTORY. NONE OF COMPONENTS ARE SPECIFICALLY REGULATED OR
PROPOS ED FOR REGULATION UNDER THE FEDERAL CLEAN WATER ACT INCLUDING THE EPA
LIST OF 129 PRIORITY WATER POLLUTANTS OR EPA THE LIST OF OF TOTAL TOXIC
ORGANIC (TTO) (40 CFR 413.02). CANADIAN W CLASSIFICATI ON: CLASS D DIVISION 2
SUBDIVISION B-TOXIC MATERIAL.
State Regulatory Information: NONE OF COMPONENTS OF THIS PRODUCT IS LISTED IN
CALIFORNIA'S SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT OF
1986-PROPOSITION AS A CHEMICAL KNOWN TO CAUSE CANCER, BIRTH DEFECTS, OR OTHER
REPRODUCTIVE HARM.
=======================================================
Other Information
=======================================================
Other Information: NFPA CODES: HEALTH -2, FLAMMABILITY -2, REACTIVITY -0.
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: AXAREL 6000
Company: PETROFERM INC
Street: 5415 FIRST COAST HWY
City: FERNANDINA BEACH FL
Zipcode: 32034
Health Emergency Phone: 904-261-8286;703-527-3887
Label Required IND: Y
Date Of Label Review: 11/13/2001
Status Code: A
Origination Code: F
Eye Protection IND: YES
Skin Protection IND: YES
Signal Word: WARNING
Respiratory Protection IND: YES
Health Hazard: Slight
Contact Hazard: Slight
Fire Hazard: Moderate
Reactivity Hazard: None
Hazard And Precautions: ACUTE: INHALATION: MAY CAUSE IRRITATION OF THE UPPER
RESPIRATORY TRACT. INGESTION: MAY CAUSE IRRITATION OF THE MOUTH, THROAT, AND
GASTROINTESTINAL TRACT WITH NONSPECIFIC DISCOMFORT SUCH AS NAUSEA, HEA DACHE,
DIARRHEA, THIRST, AND WEAKNESS. SKIN: MAY CAUSE IRRITATION. SIGNIFICANT SKIN
PERMEATION AND SYSTEMIC TOXICITY AFTER CONTACT APPEAR UNLIKELY. EYES: LIQUID
VAPOR CONTACT MAY CAUSE EYE IRRITATION WITH TEARING OR BLURRING OF VISION.
CHRONIC: NOT SPECIFIED BY MANUFACTURER (FP N).
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.

*** END OF RECORD ***
Search More   
ALL PAGES On Chemical Property IN THIS GROUP
NAMECAS
TITANIUM/TITANIUM ALLOY, TITANIUM CP, TITANIUM 6A1-4V, ETC 7440-32-6
7429-90-5
7440-47-3
1309-37-1
7439-98-7
7440-02-0
7440-31-5
1314-62-1
7440-67-7
060-1, POSITRON ULTRA HIGH PURITY DIELECTRIC SOLVENT
IMPERIAL 2075TH, HYDRAULIC FLUID PETROLEUM BASE ISO 32
RYDLYME, RID-LIME
DINITROL AV 30
DINITROL AV 30
DINITROL AV 30
DINITROL AV 100D
DINITROL AV 100D
SPRAY PAINT (AEROSOL) SO-SURE WHITE 37875 67-64-1
74-98-6
108-88-3
64475-85-0
106-97-8
75-28-5
ELECTRONIC SOLV #631-914 (BULK FORMULATED)
SURROGATE STANDARD MIXTURE, STM-330N 67-56-1
460-00-4
2037-26-5
SO-SURE CORROSION PREVENTIVE COMPOUND 67-63-0
811-97-2
8032-32-4
8030-30-6
78-83-1
107-98-2
108-88-3
71-36-3
64741-65-7
64741-97-5
25619-56-1
PLASTIC AND METAL ADHESIVE #634
MANGANESE DIOXIDE LITHIUM PRIMARY BATTERIES
13501, METEX STRIP AID
HALOCARBON 25-50 GREASE 9002-83-9
7631-86-9
PETRON PLUS TM INDUSTRIAL SUPER LUBE (NON-AEROSOL) 12845
FC-5158 DYNAMAR MOLD RELEASE
COBALT ALLOY CASTINGS, MAR M-508, X-40 7429-90-5
7440-47-3
7440-48-4
7440-50-8
7440-58-6
1309-37-1
7439-96-5
7439-98-7
7440-02-0
7440-25-7
13463-67-7
7440-33-7
7440-65-5
866, TEC-RINSE
PLY#2 PROTECTIVE SKIN CREAM
FREPON 22 75-45-6
ENERPAC HF & HOF HYDRAULIC OIL
ILSCO DE-OX ANTI-OXIDANT
POLYSPEC FLEX FR-PART A(A760)/(A765)CLEAR OR PIGMENTED 15625-89-5
56803-37-3
68609-97-2
25085-99-8
TOXIC SUBSTANCES MIX #1 AT 2000 UG/ML IN METHYLENE CHLORIDE 95-95-4
65-85-0
95-48-7
106-44-5
75-09-2
DEFOAMER (SPRAY WASH APPLICATIONS)
AXAREL 6000 64742-47-8
DETERGENT GENERAL PURPOSE NONIONIC 9016-45-9
DETERGENT GENERAL PURPOSE, LIQUID, HARD SUR 27176-87-0
9016-45-9
RED GAGE OIL 64742-47-8
64742-52-5
64742-46-7
ACTIVATED CHEMILUMINESCENT PROD (REV OXALATE COMP) ALL COLOR 75-65-0
131-11-3
7722-84-1
9002-88-4
JET DRY, AUTOMATIC WAREWASHING RINSE AID
JET DRY, AUTOMATIC WAREWASHING RINSE AID
JET DRY, AUTOMATIC WAREWASHING RINSE AID
LPS 1 GREASELESS LUBRICANT
MOLYLUBE ANTI-SEIZE MIXTURE
AMS 5376, IRON-BASE ALLOY CASTINGS 7440-48-4
7440-50-8
1309-37-1
7440-02-0
7440-47-3
007429-90-5
7439-98-7
7439-96-5
AMS5366, IRON-BASE ALLOY CASTINGS 1309-37-1
7440-02-0
7439-96-5
7439-98-7
7440-50-8
7440-48-4
7440-47-3
007429-90-5
AMS5355, IRON-BASE ALLOY CASTINGS 1309-37-1
7440-02-0
7439-98-7
7440-48-4
7440-50-8
7439-96-5
7440-47-3
007429-90-5
AMS5350, IRON-BASE ALLOY CASTINGS 7440-02-0
1309-37-1
7439-96-5
7439-98-7
7440-50-8
7440-48-4
7440-47-3
007429-90-5
17-4 PH, IRON-BASE ALLOY CASTINGS 7439-98-7
7440-02-0
1309-37-1
7439-96-5
7440-50-8
007429-90-5
7440-47-3
7440-48-4
SAE 310, IRON-BASE ALLOY CASTINGS 007429-90-5
7440-48-4
7440-47-3
7440-50-8
7439-96-5
7440-02-0
1309-37-1
7439-98-7
SAE 347, IRON-BASE ALLOY CASTINGS 007429-90-5
7440-47-3
7440-48-4
7440-50-8
7439-98-7
7439-96-5
1309-37-1
7440-02-0
SAE 410, IRON-BASE ALLOY CASTINGS 7440-02-0
7439-98-7
7440-47-3
007429-90-5
7439-96-5
1309-37-1
7440-48-4
7440-50-8
N 155, IRON-BASE ALLOY CASTINGS 007429-90-5
7440-47-3
7440-48-4
1309-37-1
7439-96-5
7440-50-8
7439-98-7
7440-02-0
AOS HEAT SINK COMPOUND, 52022
UNITRAN DEXRON III/MERCON AUTOMATIC TRANSMISSION FLUID 64742-54-7
GLASS CLEANER, REGULAR, TYPE 1, CLASS 1 1336-21-6

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com