===================== Product Identification =====================
MSDS NAME:HYSOL EA 956 PART B
NIIN:00-463-7042
Kit Part:Y
MSDS Number: CCGFN
=== Responsible Party ===
Company:DEXTER HYSOL AEROSPACE INC DIV OF DEXTER CORP THE
Address:2850 WILLOW PASS RD
Box:312
City:PITTSBURGH
State:CA
ZIP:94565-3299
Country:US
Info Phone Num:510-458-8000/202-483-7616
Emergency Phone Num:510-458-8000/202-483-7616
CAGE:33564
=== Contractor Identification ===
Company:DEXTER CORPORATION ADHESIVE & COATING SYSTEMS
Address:2850 WILLOW PASS ROAD
Box:312
City:BAY POINT
State:CA
ZIP:94565-3299
Country:US
Phone:202-483-7616
CAGE:33564
============= Composition/Information on Ingredients =============
Name:POLYAMIDE RESIN
Fraction by Wt: 40-70%
Name:DIETHYLENETRIAMINE, ETHYLENEDIAMINE, N-(2-AMINOETHYL);
BIS(2-AMINOETHYL)AMINE *96-3*
CAS:111-40-0
RTECS #:IE1225000
Fraction by Wt: 10-30%
Other REC Limits:4 MG/CUM
ACGIH TLV:1 PPM (SKIN)
Name:TRIETHYLENETETRAMINE, EPOXY HARDNER
CAS:112-24-3
RTECS #:YE6650000
Fraction by Wt: 5-10%
Name:VOLATILE ORGANIC CONTENT: <10 G/L
RTECS #:9999999VO
===================== Hazards Identification =====================
LD50 LC50 Mixture:ORAL LD50(RAT): >4000 MG/KG (SEE SUPP)
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN/EYES: CORROSIVE, CHEMICAL BURNS,
IRRITATION. INHALATION: NOSE & THROAT IRRITATION.
REPEATED/PROLONGED SKIN CONTACT MAY RESULT IN BURNS & POSSIBLE
ALLERGIC SENSITIZATION.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:IRRITATION, CHEST DISCOMFORT, BURNS.
Medical Cond Aggravated by Exposure:SKIN SENSITIZATION.
======================= First Aid Measures =======================
Eyes: FLUSH W/WATER FOR 15 MINS. SKIN: WASH THOROUGHLY W/SOAP
& WATER. INHALATION: REMOVE TO FRESH AIR. INGESTION: DRINK PLENTY
OF WATER. OBTAIN MEDICAL ATTENTION IN ALL CASES.
===================== Fire Fighting Measures =====================
Extinguishing Media:DRY CHEMICAL, HALON, WATER SPRAY, FOAM/FOG.
Fire Fighting Procedures:WEAR SCBA & FULL PROTECTIVE CLOTHING.
CARTRIDGE RESPIRATORS DON'T PROVIDE ADEQUATE PROTECTION FOR
FIGHTERS/EXOTHERM MITIGATION.
Unusual Fire/Explosion Hazard:MAY LIBERATE LARGE QUANTITIES OF DENSE
FOUL-SMELLING SMOKE WHICH MAY CONTAIN UNIDENTIFIED TOXIC GASES.
================== Accidental Release Measures ==================
Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES & SAFETY
GLASSES. ABSORB W/ABSORBENT MATERIAL SUCH AS VERMICULITE/SAND.
SCRAPE UP/SHOVEL INTO DOT APPROVED WASTE CONTAINER.
====================== Handling and Storage ======================
Handling and Storage Precautions:STORE AT ROOM TEMP FOR UP TO 12
MONTHS. KEEP CONTAINER TIGHTLY CLOSED WHEN NOT IN USE. FOLLOW
CURING SCHEDULE & MIXING RATIOS.
Other Precautions:EMPTY CONTAINERS RETAIN PRODUCT RESIDUE, HANDLE EMPTY
CONTAINERS AS IF THEY WERE FULL. DON'T CUT, GRIND, WELD/DRILL
ON/NEAR CONTAINERS.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:IF LOCAL EXHAUST VENTILATION IS INADEQUATE, A
RESPIRATOR EQUIPPED W/ORGANIC VAPOR CARTRIDGES MAY BE APPROPRIATE.
Ventilation:LOCAL EXHAUST VENTILATION.
Protective Gloves:BUTYL RUBBER, POLYVINYL CHLORIDE
Eye Protection:SAFETY GLASSES W/SIDE SHIELDS
Other Protective Equipment:CHEMICAL GOGGLES, NITRILE RUBBER GLOVES,
LONG SLEEVED SHIRT & TROUSERS, EYEWASH, SAFETY SHOWER.
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING.
Supplemental Safety and Health
CONDITIONS TO AVOID CONT'D: DON'T HEAT MIXED ADHESIVE >125F UNLESS
CURING SURFACES TO BE BONDED. FAILURE MAY RESULT IN EXCESSIVE HEAT
BUILD-UP CAUSING AN EXOTHERM. EXOTHERM HAS THE POTENTIAL FOR RELEA
SE OF TOXIC GASES. ORAL LD50 INFORMATION IS FOR POLYAMIDE RESIN.
================== Physical/Chemical Properties ==================
HCC:C2
Boiling Pt:B.P. Text:405F
Vapor Density:>1
Spec Gravity:0.96
Viscosity:*
Solubility in Water:COMPLETE
Appearance and Odor:AMBER LIQUID W/AMMONIACAL ODOR.
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS/MINERAL ACIDS.
Stability Condition to Avoid:AVOID MIXING RESIN & CURING AGENT IN
BATCHES >1 LB UNLESS YOU PLAN TO USE IMMEDIATELY. (SEE SUPP)
Hazardous Decomposition Products:CO, NITROGEN OXIDES, ALDEHYDES,
UNDETERMINED ORGANICS.
==================== Disposal Considerations ====================
Waste Disposal Methods:INCINERATION IN AN EPA-APPROVED WASTE
INCINERATOR IS PREFERRED. CHEMICAL ADDITIONS, PROCESSING/OTHERWISE
ALTERING MATERIAL MAY MAKE MANAGEMENT INFORMATION HEREIN
INCOMPLETE, INACCURATE/INAPPROPRIATE. DISPOSE OF IAW/FEDERAL,
STATE & LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|