Distributed By: MSDS 088
Invensys Foxboro Foxboro Rev Date: October 2006
Foxboro, MA 02035 U.S.A. Part Number X0118CC
1-866-746-6477 Page 1 of 2
LUBRIPLATE
MATERIAL SAFETY DATA SHEET
Section 1
PRODUCT NAME OR NUMBER FORMULA
LUBRIPLATE Aero Lithium Soap, Mineral Oil and Additives
GENERIC/CHEMICAL NAME: USDA AUTHORIZATION:
Petroleum Lubricating Grease H-2
Manufacturer's Name Emergency Telephone Number
Fiske Brothers Refining Co. 1-800-255-3924 - CHEM-TEL (24 hour)
Address Telephone Number for Information
1500 Oakdale Ave., Toledo, Ohio 43605 - 129 Lockwood St., Newark, NJ 07105 419-691-2491 - Toledo Office
Section 2 - Hazardous Ingredients/Identity Information
Hazardous Components OSHA PEL ACGIH TLV Other Limits Recommended % (optional)
Non-hazardous
Health - 1, Flammability - 1, Reactivity - 0
Hazardous Material Identification System (HMIS):
Not a Controlled Product under (WHMIS) - Canada Special Protection: See Section 9
Section 3 - Health Hazard Data
5 mg/m3 for oil mist in air. OSHA Regulation 29 CFR 1910.1000
Threshold Limit Value
Effects of Overexposure Prolonged or repeated skin contact may cause skin irritation. Product contacting the eyes may cause eye irritation.
Human health risks vary from person to person. As a precaution, exposure to liquids, vapors, mists and fumes should be minimized. This
product has a low order of acute oral toxicity, but minute amounts aspirated into the lungs during ingestion may cause mild to severe
pulmonary injury.
NTP? No IARC Monographs? No OSHA Regulated? No
Carcinogenicity:
Section 4 - Emergency and First Aid Procedures
EYE CONTACT: Flush with clear water for 15 minutes or until irritation subsides. If irritation persists, consult a physician.
SKIN CONTACT: Remove any contaminated clothing and wash with soap and warm water. If injected by high pressure under skin,
regardless of the appearance or its size, contact a physician IMMEDIATELY. Delay may cause loss of affected part of the body.
INHALATION: Vapor pressure is very low and inhalation at room temperature is not a problem. If overcome by vapor from hot product,
immediately remove from exposure and call a physician.
INGESTION: If ingested, call a physician immediately. Do not induce vomiting.
Section 5 - Fire and Explosion Hazard Data
COC - 375oF LEL 0.9% UEL 7.0%
Flash Point (Method Used) Flammable Limits
Foam, Dry Chemical, Carbon Dioxide or Water Spray (Fog)
Extinguishing Media
Cool exposed containers with water. Use air-supplied breathing equipment for
Special Fire Fighting Procedures
enclosed or confined spaces.
Do not store or mix with strong oxidants. Empty containers retain residue.
Unusual Fire and Explosion Hazards
Do not cut, drill, grind, or weld, as they may explode.
MSDS 088
Part Number X0118CC
Page 2 of 2
PRODUCT NAME OR NUMBER - LUBRIPLATE Aero
Section 6 - Physical/Chemical Characteristics
>550oF 0.884
Boiling Point Specific Gravity (H 2O = 1)
<0.01 Semi-solid
Vapor Pressure (mm Hg.) Melting Point
>5 <0.01
Vapor Density (AIR = 1) Evaporation Rate
(Butyl Acetate = 1)
Negligible
Solubility in Water
Smooth, off-white grease with mineral oil odor.
Appearance and Odor
Section 7 - Reactivity Data
Unstable N/A
Stability Conditions to Avoid
Stable X
Avoid contact with strong oxidants like liquid chlorine, concentrated oxygen.
Incompatibility (Materials to Avoid)
Hazardous Decomposition or Byproducts May form SO 2. If incomplete combustion, Carbon Monoxide.
May Occur Conditions to Avoid N/A
Hazardous Polymerization
Will Not Occur X
Section 8 - Spill or Leak Procedures
Steps to be taken in case material is released or spilled
Scrape up grease, wash remainder with suitable petroleum solvent or add absorbent. Keep petroleum products out of sewers and
watercourses. Advise authorities if product has entered or may enter sewers and watercourses.
Waste disposal method
Assure conformity with applicable disposal regulations. Dispose of absorbed material at an approved waste disposal facility or site.
SARA/TITLE III, Section 313 Status - Zinc Compounds < 5%
Section 9 - Special Protection Information
Normally not needed
Respiratory Protection (Specify type)
Used to capture fumes and vapors Special N/A
Ventilation Local Exhaust
Other N/A
Mechanical (General)
Protective Gloves Use oil-resistant gloves, if needed. Eye Protection If chance of eye contact, wear goggles.
Use oil-resistant apron, if needed.
Other Protective Equipment
Section 10 - Special Precautions
Precautions to be taken in handling and storing
Keep containers closed when not in use. Do not handle or store near heat, sparks, flame, or strong oxidants.
Other Precautions
Remove oil-soaked clothing and launder before reuse. Cleanse skin thoroughly after contact.
The above information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of Fiske
Brothers Refining Company. The data on these sheets relates only to the specific material designated herein. Fiske Brothers
Refining Company assumes no legal responsibility for use or reliance upon this data.
Date Prepared: January, 2006 Prepared by: James R. Kontak
|