Revised: 12/18/06
MATERIAL SAFETY DATA SHEET
POLY CURE
1. COMPANY IDENTIFICATION
Manufacturer: SpecChem
444-B Richmond Ave.
Kansas City, KS 66101
Phone (866) 791-8700
24 Hour Emergency Contact: CHEMTREC (800) 424-9300
2. COMPOSITION INFORMATION
Component CAS # % by weight
Stoddard Solvent Mixture 8052-41-3 75%
3. HAZARDS IDENTIFICATION
Component Exposure Limit
Stoddard Solvent TWA: 100 ppm, ACGIH (TLV)
TWA: 500 ppm, OSHA (PEL)
NFPA CLASSIFICATION (0=Least, 1=Slight, 2=Moderate, 3=High, 4=Extreme)
Health 1, Fire 2, Reactivity 0
HMIS CODES (0=Least, 1=Slight, 2=Moderate, 3=High, 4=Extreme)
Health 1, Flammability 2, Reactivity 0
HAZARD DESCRIPTION: May be harmful if swallowed or inhaled.
May cause irritation to skin, eyes, and respiratory tract.
POTENTIAL HEALTH EFFECTS
INHALATION: No information found, but compound should be handled as a potential health hazard. May cause
irritation to the respiratory tract. Symptoms may include coughing, sore throat, labored breathing, and chest pain.
Go to fresh air if irritation persists.
INGESTION: May cause irritation to the gastrointestinal tract. Symptoms may include nausea, vomiting, and
diarrhea.
SKIN CONTACT: Prolonged of repeated contact may cause irritation, defatting, or dermatitis.
EYE CONTACT: May cause irritation, redness, blurred vision, and pain.
CHRONIC EXPOSURE: No information found.
AGGRAVATION OF PRE-EXISTING CONDITIONS: No information found.
4. FIRST AID PROCEDURES
EYE CONTACT: Immediately flush eyes with plenty of water for 15 minutes, lifting lower or upper eyelids
occasionally. Obtain medical attention immediately.
SKIN CONTACT: Immediately flush skin with plenty of water for at least 15 minutes. Remove contaminated
clothing and shoes. Obtain medical attention. Wash clothing before reuse. Thoroughly clean shoes before reuse.
INHALATION: Remove to fresh air. Give artificial respiration if not breathing. Give oxygen if breathing is
difficult. Obtain medical attention.
INGESTION: Give large amounts of water to drink. Never give anything by mouth to an unconscious person.
Obtain medical attention.
5. FIRE FIGHTING MEASURES
Flash Point: 105掳 F (TCC)
Auto-ignition Temperature: No data available.
Upper Explosion Limit: 6.0
Lower Explosion Limit: 0.5
Page 1 of 3
Revised: 12/18/06
MATERIAL SAFETY DATA SHEET
POLY CURE
EXTINGUISHING MEDIA: Alcohol foam, dry chemical, carbon dioxide.
EXTINGUISHING MEDIA TO AVOID: Avoid use of water
SPECIAL FIREFIGHTING PROCEDURES: In the event of a fire, wear full protective clothing and NIOSH
approved self-contained breathing apparatus with full facepiece operated in the pressure demand or other positive
pressure mode. 鈥淓MPTY鈥? CONTAINER WARNING: 鈥淓mpty鈥? containers retain residue (liquid and/or vapor) and
can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat,
flame, sparks, or other sources of ignition; they may explode and cause injury or death.. 鈥淓mpty鈥? drums
should be completely drained, properly bunged and promptly returned to a drum reconditioner. All other containers
should be disposed of in an environmentally safe manner and in accordance with governmental regulations. For
work on tanks refer to OSHA, ANSI Z 49.1, and other governmental and industrial references pertaining to cleaning,
repairing, welding, or other contemplated operations.
6. ACCIDENTAL RELEASE MEASURES
LARGE SPILLS: Precaution should be taken in the event of a spill. Floor surfaces will become slippery. Evacuate
the hazard area of unprotected personnel. Dike and contain with suitable absorbent. Shut off source of leak only if
it is safe to do so. Do not allow to enter sewers or open waterways. Advise authorities if product has entered
sewers, waterways, or extensive land areas. SMALL SPILLS: Take up with absorbent materials such as sand or
sawdust and place in non-leaking containers. Dispose of in accordance with all federal, state, and local regulations.
7. HANDLING AND STORAGE
HANDLING: For industrial use only. Avoid skin and eye contact. Minimize breathing vapor or mist. Respiratory
protection is required when ventilation is inadequate. Cleanse skin thoroughly after contact, before breaks and
meals, and at the end of a work period. Product is readily removed from skin by waterless hand cleaners following
by washing thoroughly with soap and water. STORAGE: Store in a cool, dry location and in accordance with good
industrial practices. Keep containers closed when not in use.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
VENTILATION: Use local exhaust to capture vapor or mists if necessary. Local exhaust is preferred over general
exhaust because it can control the emissions of the contaminant at its source, preventing dispersions into the general
work area. Provide ventilation sufficient to prevent exceeding OSHA PELs.
RESPIRATORY PROTECTION: For emergencies or instances where the exposure levels are not known, use a full-
facepiece positive-pressure, air-supplied respirator.
SKIN PROTECTION: Wear impervious protective clothing, including gloves, boots, lab coat, apron, or coveralls,
as appropriate to prevent skin contact.
EYE PROTECTION: Use chemical safety goggles and/or a full face shield where splashing is possible. Maintain
eye wash fountain and quick-drench facilities in work area.
9. PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Clear amber liquid SPECIFIC GRAVITY: 0.79
ODOR: Mineral Spirits Odor pH: N/A
BOILING POINT: 310oF
VAPOR PRESSURE: 0.22 mm Hg @ 20掳C VAPOR DENSITY: 4.7 (Air = 1)
SOLUBILITY IN WATER: Negligible
10. STABILITY AND REACTIVITY
STABILITY: Stable.
CONDITIONS TO AVOID: Incompatibles.
MATERIALS TO AVOID: Strong oxidizing agents, strong acids, strong bases.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon dioxide and carbon monoxide may form when heated to
decomposition.
HAZARDOUS POLYMERIZATION: Will not occur.
Page 2 of 3
Revised: 12/18/06
MATERIAL SAFETY DATA SHEET
POLY CURE
11. TOXICOLOGICAL INFORMATION
No LD50/LC50 information is available relating to normal routes of occupational exposure.
EYE EFFECTS: May cause irritation, redness, and pain.
SKIN EFFECTS: May cause irritation with redness and pain.
ORAL EFFECTS: May cause irritation to the gastrointestinal tract. Symptoms may include nausea, vomiting, and
diarrhea.
INHALATION EFFECTS: May cause irritation to the respiratory tract. Symptoms may include coughing, sore
throat, labored breathing, and chest pain.
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL FATE: No information available.
ECOTOXICITY: No information available.
FURTHER INFORMATION: None.
13. DISPOSAL CONSIDERATIONS
When disposed of properly, this product does not meet RCRA classification or listing for hazardous waste. Dispose
in accordance with all applicable federal, state, provincial, and local environmental regulations. Empty containers
should be recycled or disposed of through an approved waste management facility.
Disposal methods identified are for the product as sold. For proper disposal of used material, an assessment must be
completed to determine the proper and permissible waste management options permissible under applicable rules,
regulations and/or laws governing your location.
14. TRANSPORT INFORMATION
DOT SHIPPING LABEL: Combustible Liquid, N.O.S., Combustible Liquid, NA1993, PGIII
HAZARD CLASS: 3
Flammable placards required only when packaged in containers holding 119 gallons or more or when
shipping 1,000 lbs or more by air or water.
15. REGULATORY INFORMATION
FEDERAL/NATIONAL
This product is not hazardous as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SUPERFUND AMENDMENTS AND REAUTHORIAZATION ACT OF 1986 (SARA) TITLE III (Emergency
Planning and Community Right to Know Act) SECTION 313
This product contains the following substances subject to the reporting requirements of Section 313 of Title III of
the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372:
NONE
TOXIC SUBSTANCES CONTROL ACT (TSCA)
All components of this product are on the TSCA Inventory or are exempt from the TSCA Inventory requirements.
16. OTHER INFORMATION
The information and recommendations contained herein were obtained from sources we believe to be accurate and
reliable as of the date revised. However, manufacturer does not warrant or guarantee their accuracy or reliability,
and shall not be liable for any loss or damage arising out of the use thereof. The information and recommendations
are offered for the user's consideration and examination and it is the user's responsibility to satisfy itself that they are
suitable and complete for its particular use.
Page 3 of 3
|